-
product
Cut Susceptibility Tester
King Design Industrial Co., Ltd.
Equipment conforms to IEC61730 MST12 specification. Pre- or post-round can be selected for control wiring connection. With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time. Equipped with rings at both front and rear end; used to connect a rope and control the driving direction. Use replaceable special cutting chip.
-
product
AC Susceptibility
The AC Susceptometer option uses a small primary excitation coil to apply an AC field to a sample (typically 1mT at frequencies from 0.1 Hz 10000 Hz). A pair of secondary pick-up coils positioned close to the excitation coils are used to detect the sample response.
-
product
Flow Switches
Not susceptible to contamination and can be oriented in any pipe configuration make these flow switches for liquid or air maintenance free and reliable. Mechanical and electronic designs available
-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Cross Sections and Metallography
Rocky Mountain Laboratories, Inc.
Cross sections are prepared by mounting samples in epoxy and then grinding and polishing the mount for imaging in the optical microscope or Scanning Electron Microscopy (SEM). Valuable information from cross sectioning can include: film thicknesses, inclusions, corrosion thickness, dimensional verification, and subsurface defects. Metallographic cross sections are typically etched to reveal the microstructure. Microstructural analysis can provide information about heat treatment history, corrosion susceptibility, as well as undesirable microconstituents.
-
product
Transient Pulse Generator
8282-1
The Model 8282-1 Transient Pulse Generator was designed for screen room use in making conducted spike susceptibility tests. It provides all the waveshapes required by MIL-STD-461B/C and many other military EMI specifications
-
product
Flow Switches
Not susceptible to contamination and can be oriented in any pipe configuration make these flow switches for liquid or air maintenance free and reliable. Mechanical and electronic designs available
-
product
RH Temp External Probe
An external Relative Humidity and Temperature Probe for tight or remote locations. Every RH reading is temperature compensated for accurate readings. For environmental susceptibility, see Data Logger specification. Maximum extension is 30m (100').
-
product
Electromagnetic Immunity Scanner
SmartScan 350
Reproducing similar soft or hard failure to the gun test - Flexible automatic failure detection module - Susceptibility map generation- Automatic report generation- Flexible scan area editor (SAE)- Flexible display (3D, histogram)- Matlab support- Expandability (EMI scan, phase measurement, NFFF transformation)- Custom design probes
-
product
MagTest System
A System to generate magnetic fields and to perform tests regarding the susceptibility against magnetic fields.
-
product
EMC Test System
An electric product might cause the malfunction to other electric appliances by discharging the emission noise from it, or is oppositely caused the malfuction by the emission noise from other electric appliances. The former is checked by the EMI test and the latter is checked by the EMS test. The international standard like the CISPR standard is provided so that such an accident should not happen, and the manufacturer must declare by themselves beforehand that their product meets the standard. The generic name of the EMI test (Electro-Magnetic Interference) of the emission measurement and the EMS test (Electro-Magnetic Susceptibility) of the immunity
-
product
Antenna, Log Periodic
EM-6954 | 70 MHz – 1 GHz
The EM-6954 is designed to meet antenna requirements for both field strength measurement and radiated susceptibility in the 70 MHz to 1 GHz frequency range.
-
product
Emergency Conditions Testing
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Electromagnetic Immunity Scanner
SmartScan BASIC
The BASIC is manually operated system for performing susceptibility scanning at the system level with minimal data storage capability. This system includes:1. Up to 8kV (optional. 4kV base) pulse generator for ESD susceptibility testing- Camera and camera shutter to take DUT picture and failing spots- Control computer2. Up to 8kV Probe Sets:- 1mm Hx/y Field Probe- 5mm Hx/y Field Probe- D=8mm Hz Field Probe- D=8mm Ez Field Probe- Contact API for custom design probes3. Manual input of testing location and failing condition over the DUT to be included in final report.
-
product
Thermocouple
This sensor uses a K-type Chromel/Alumel thermocouple and is intended for use in high-temperature, high-vibration environments. Control units and data loggers support K-type thermocouples. The sensor is short and compact to minimise its susceptibility to vibration.
-
product
Power Supply
The Power Supply Systems are the heart of any experiment. They provide the High voltage and Low voltage required by the detectors and by the related front-end electronics. The quality of the power supply is critical to obtain the best performance from the set-up. The sensibility of modern detectors, in fact, make them susceptible to any even small variation in the power supply, and so features like low Noise, low Ripple and high stability become essential in the design of a performing power supply system. Strong of 40 years of collaboration with the most important research labs worldwide CAEN offers today sophisticated High Voltage Power Supply and Low Voltage Power Supply Systems. The demonstration of this successful long-standing tradition is the “CMS Crystal Award 2009” that CAEN received for the development and production of the power system for the CMS tracker. CAEN offers a wide selection of Power Supplies in different form factors and standards:- For smaller set-ups Standalone or modular (NIM / VME) products or are the ideal fit.- For bigger set-ups, where a high number of High voltages and Low voltages is required, the Mainframe Systems and Boards (up to 48 channels/board, up to 768 channels in a single Mainframe) are the most recommended.
-
product
EMI/EMC Testing
Our Environmental Services Group performs emissions and susceptibility testing to ensure a product meets its intended performance in the ever-increasing and challenging electromagnetic environments.
-
product
VOICE OF THOR
THOR GUARD's Voice of Thor or VOT lightning alarm system is utilized to provide a unique aubible warning pattern when the area THOR GUARD is monitoring has become susceptible to a lightning strike. Simultaneously during the hazard time, LED strobe lights can be utilized to provide a continued visible notification of the impending hazard. THOR GUARD allows for a base horn with the remotes, either electric or solar powered, being controlled using THOR GUARD’s dedicated RF system. When combined with the Guardian Emergency Notification System, a special 1-minute pattern is generated to provide for any unexpected emergency.
-
product
RF Helmholtz Coil
The Beehive Electronics 135A RF Helmholtz coil generates a well-controlled, uniform magnetic field. It can be used to calibrate magnetic field probes, such as the Beehive 100 series, or for testing the susceptibility of other devices to magnetic fields. The Helmholtz coil comes supplied with a fixture that makes it easy to calibrate Beehive 100 series probes.
-
product
Bypass Diode Tester
BDT
Our bypass diode thermal tester is designed to assess the adequacy of the thermal design and long-term reliability of PV modules bypass diodes, which are used to limit the detrimental effects of module hot spot susceptibility.
-
product
Magnetic Susceptibility Meter for Multi-Layer Survey
MULTI KAPPA
Multi Kappa instrument serves for fast field survey allowing both spot measurement and mapping by means of several probes. Together with GF Instruments traditional pocket magnetic susceptibility meters cover wide range of demands for accurate susceptibility measurement on ground surface, outcrops and samples of rock and soil. geological survey, archaeology, agriculture and forestry, raw material prospecting, mineralogy, sedimentology, detection of metallic objects, UXO survey.
-
product
Partial Discharge Tester (Dry Type)
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Electromagnets
The Lake Shore electromagnets (EM-V Series) produce magnetic fields with a variety of indexed air gap and pole cap configurations. The EM-V Series is ideally suited for integration into customer-designed magnetic test platforms for applications including magneto-optical studies, magnetic hysteresis studies, in-line annealing, Hall effect studies, susceptibility measurements, spin magnetic resonance demonstrations, and biological studies.
-
product
Universal Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
There are models with charge output and with IEPE compatible voltage output. The transducers of KS series have a shear type sensing element making them less susceptible to thermal transients and base strain. The accelerometers of KD series have a compression type sensing element combining rugged design, precision and low cost.
-
product
Automotive EMC Testing
Having been assessed by Ford Detroit’s EMC expert, we are Australia’s only Ford (and NATA) accredited automotive EMC test laboratory. Others have tried, but none have succeeded. Ford does not accept reports from EMC labs that are not on the Ford list of accredited labs. The scope ranges from component to complete vehicle level EMC testing for Australian and overseas manufacturers. We also have a fully dedicated CISPR 25 Electronic Sub Assembly (ESA) chamber, another large CISPR 25 anechoic chamber for vehicle testing or susceptibility levels in excess of 500V/m. We possess a vast array of specific automotive EMC test equipment such as BCI’s, tri-plate’s, and striplines for susceptibility and emissions testing to meet the most stringent automotive EMC requirements. Our Australian and overseas customers use our labs because they know that our reports will be accepted and will not be questioned.
-
product
µModule Isolated Transceivers
Analog Devices µModule (micromodule) isolated transceivers provide robust galvanic isolation for digital serial communication interfaces, including SPI, I2C, RS-485/RS-422, RS-232, and USB. Isolation barriers are implemented using Ethernet transformers, coupling capacitors, or embedded inductors. All devices are simple to configure, have very low EMI susceptibility and emissions, and feature high noise immunity to preserve signal integrity.
-
product
Connector Testing
If your product uses a connector or terminal, it can be susceptible to a unique set of failures that warrant specific connector testing conditions to determine the robustness of your design.
-
product
ESD Discharge Simulator
Model 9910 PurePulse/PinScan
Model 9910 PurePulse / PinScan is used to determine the ESD susceptibility level of electronic devices up to ±4kV. PurePulse generates ESD pulses up to 4kV for testing electronic devices for susceptibility to Electrostatic Discharge (ESD) using HBM, MM and HMM models. PinScan provides automatic sequencing of ESD testing of up to 128 pin devices, applying a discharge, thenperforming a curve-trace test to identify a failure.
-
product
Magnetic Susceptibility Meter
SM-20
The SM-20 magnetic susceptibility meter is very useful tool for a number of geological and geophysical applications where the unique sensitivity of 10-6 SI units together with its small, shirt-pocket size and low weight are appreciated.
