-
Product
Standard GaN Amplifiers
-
A GaN (Gallium Nitride) amplifier is a power amplifier that uses GaN, a wide-bandgap semiconductor material, to provide high power density, efficiency, and frequency capabilities.
-
Product
Premium Headphone Amplifier
A 2
-
A premium model with a discrete configuration and full analog circuit that was created to drive the T 1 thoroughly.
-
Product
Transimpediance Amplifiers
-
The UDT TRAMP products are transimpedance amplifier (current-to-voltage) instruments that provide a low input impedance to accurately measure the short circuit current of phototransducers such as silicon and germanium photodetectors, vacuum photodiodes and photomultiplier tubes. The range includes the economically priced TRAMP, and for ultra precision and accuracy, the TIA-3000.
-
Product
High Voltage Amplifier
HA-805
-
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
Product
Amplifiers
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
Low Noise Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM low noise amplifier MMICs cover a frequencies from DC to 86 GHz operation for a wide range of applications, including network infrastructure, radar and communication systems. MACOMs portfolio of low noise amplifiers offer a broad array of noise figures, input IP3, and input power in bare die and a variety of package types. Offerings include wideband distributed topologies and self or actively biased configurations tailored to system design needs.
-
Product
Air Amplifiers
-
Nex Flow® Air amplifiers are compact, low cost air flow “movers” that are virtually maintenance free. Applications include the venting of fumes and smoke, conveying of low weight materials, and entraining a high volume of air to cool, blow off, and dry. Air Amplfiiers use the “Coanda effect” to draw in the surrounding atmosphereic air while consuming only aminimal amount of compressed air. These products can amplify airflow up to 17 times (depending on the size) resulting in dramatcally reduced levels of noise. Air Amplifiers (also called Air Movers) draw in atmospheric air from the back of the unit as well as having downstream entrainment further amplifying the flow. They are used for cooling and venting. While the force produced for blow off decreases as the amplifier outlet diameter increases, these Air Movers are ideal for cooling because of the high velocity outlet fow and and are much more effective for cooling compaed to air nozzles.
-
-
Product
Amplifiers & Buffers
-
Renesas amplifiers are among the industry's highest-performance, highest-value amplifier ICs on the market. Our broad operational amplifier (op amp) portfolio provides for a wide range of next-gen precision instrumentation, medical, communication and industrial process control applications where innovation, reliability and dependability is central to the analog designs.
-
Product
Power Amplifiers
-
Power amplifiers are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a high output power with superior power added efficiency (PAE) and high linearity. While standard models focus on general purpose applications, additional models with differing frequency ranges, gains and power levels are listed on the website. Custom designs are also offered to meet any user’s specific needs.
-
Product
Amplifiers And Linear ICs
-
For the simplest to the most complex designs, our extensive portfolio of amplifiers and comparators enables you to develop low-risk solutions with minimal risk of a forced redesign. These devices are also backed by our client-driven obsolescence practice of continuing to supply a product for as long as possible and while demand for the product exists.
-
Product
Power Amplifiers
-
Precision Test makes two power amplifiers for use with our FSG series of hand held signal generators.
-
Product
Low Noise Amplifier
-
R&K’s Low Noise Amplifier (LNA) series products are a type of small signal amplifiers but with excellent noise figure. LNA is designed to significantly minimize additional noise to be introduced inside the product, and capable to amplify the input RF signal to the required level with minimal impact from noise on output RF signal.
-
Product
System Amplifiers
-
The perfect combination of high performance, wide bandwidth and low noise
-
Product
Measuring Amplifiers
VibroMatrix
-
The VibroMatrix measuring system consists of the USB measuring amplifier "InnoBeamer" and various software modules, which can be put together individually. Suitable for your measurement task. All you need is a computer or a notebook. The software enables you to measure in real time and record your data for later offline analysis in the office.
-
Product
SOA & Raman Amplifier
-
They are designed for distributed Raman amplification in a narrow spectral range in C band.
-
Product
Amplifier Module
LNAM-FBX
-
Ultra-low-noise voltage amplifier module (LNAM) with ac coupled FET input allowing measurements between 1 Hz and 20 MHz. High gain precision and low distortion are achieved by using internal negative feedback and >1000 V/µs output stages.
-
Product
Crossed-Field Amplifiers
CFAs
-
Communications & Power Industries
CPI BMD’s crossed-field amplifiers (CFAs) are broadband, phase-stable microwave amplifiers used in coherent radar chains to efficiently generate very high peak output powers from relatively low input voltages which can be either applied to the cathode or an electrode similar to a TWTs cathode or grid pulsing, and in relatively small, lightweight packages. These characteristics make CFAs particularly well-suited for applications in which the transmitter must be either airborne, transportable, mobile or portable.
-
Product
Distribution Amplifier
-
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
Product
Full W-Band Power Amplifier
SBP-7531142515-1010-E1
-
For communication and radar applications, SAGE Millimeter has released a new full W-Band power amplifier. Model SBP-7531142515-1010-E1 is a power amplifier with a typical small signal gain of 25 dB and a nominal output power of +15 dBm across the frequency range of 75 to 110 GHz. The DC power requirement for the amplifier is +15 VDC/190 mA. The mechanical configuration offers an in-line structure with WR-10 waveguides and UG-387/U-M flanges. Other port configurations, such as with 1 mm connectors or a right angle structure with WR-10 waveguides, are also available under different model numbers. Features include: Full Band, High Gain, High Output Power.
-
Product
H2S Trip Amplifier Module
TA202A
-
The TA202A is a single-channel H2S Trip Amplifier Module for use with our H2S Intelligent Sensors. It is designed to monitor H2S in parts per million (ppm) levels and provide status indication and alarm outputs.
-
Product
Amplifier Systems
-
Sutter Instrument provides a complete line of electrophysiology recording hardware and software, ideal for applications ranging from tissue slice patch clamp over dissociated cell recordings to cell line studies.
-
Product
Amplifiers
LA-1K
-
Introducting the new LA-1K RF Sensing Dual HF LDMOS 1000 Watt Amplifier. While the LA-1K will work with a wide variety of tuners and transceivers, Palstar custom-designed the LA-1K to work as the perfect match for our very popular HF-AUTO autotuner. MADE IN THE USA
-
Product
Miniature Measuring Amplifiers
MAL Series
-
5B connection technology is based on the common 5B industrial standard and is intended to be a supplement to the 5B measuring amplifiers
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
Variable Gain Amplifiers
-
50 dB Gain, 14 dBm P1dB, 100 MHz to 18 GHz, Rack Mount, Variable Gain Amplifier, 6.5 dB NF, SMA
-
Product
Power Amplifiers
-
Amplifiers with Extron patented CDRS™ – Class D Ripple Steering technology which supports high signal fidelity and clear audio.
-
Product
Preamplifier, 100 MHz to 18 GHz
87405C
Amplifier
Exceptional gain (25 dB) and flatness (1.5 dB) combined with a probe-power bias connection which eliminates the need for an additional DC power supply, makes these preamplifiers the ideal choice for spectrum analyzer or stand alone applications.
-
-
Product
DSP And Power Amplifier
DMPA12
-
The DMPA12 is a powerful digital audio processor and multi-channel power amplifier combined into a single rack space component designed to work with DM Series processors. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency. The primary applications are sound reinforcement and teleconferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design is ideally suited to mix-minus sound reinforcement systems.
