Trace
-
Product
Infiniium V-Series Oscilloscope: 13 GHz, 4 Analog Channels
DSOV134A
Oscilloscope
13 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with low noise floor (1.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
ENA Vector Network Analyzer
E5080B
Vector Network Analyzer
As devices become highly integrated, complete characterization requires a complete RF and microwave measurement solution. The E5080B provides R&D performance up to 53 GHz and advanced test flexibility. Best-in-class dynamic range, trace noise, and temperature stability guarantee reliability and repeatability.
-
Product
LANTRACKER
PH-100/120
-
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
-
Product
CX4000 – FTIR Gas Analyzer
-
Gasmet CX4000 is an industrial multi-component FTIR gas analyzer for continuous emission monitoring applications, integrated into a Continuous Emissions Monitoring system (CEMS II e). It can be used to measure up to 50 components simultaneously, and additional gases can be easily added without any hardware changes. The corrosion-resistant sample cell is heated up to 180 °C, which makes CX4000 an ideal tool for analyzing trace concentrations of pollutants in wet, corrosive gas mixtures.
-
Product
Multi-points Temperature Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
TP series of multiplex temperature meter is a kind of instrument which suits to real time monitor and trace multi-points temperature simultaneously. With the features of Simplified operation, high precision and reusable thermocouple, it is widely applied in electronic ballast, motor tools, lighting fixtures and household appliances. The application software records and save the temperature rising curve in real time for analyze purpose.
-
Product
PCI Adapter for cPCI
PCI2cPCI
-
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
Product
JTAG Emulator
Blackhawk USB560v2
-
The Blackhawk USB560v2 STM emulator has System Trace capability, along with a USB powered interface.
-
Product
High Power Fiber Optic Visual Fault Locator
VFL-700
-
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
Product
SF6 Gas Testing
-
Weshine Electric Manufacturing Co., Ltd
SF6 quantitative leak detector is an ideal tool and method for sf6 gas trace leakage inspection. It has the advantages of fast, convenient, reliable, and low maintenance cost.
-
Product
Mixed Signal Oscilloscope: 13 GHz, 4 Analog Plus 16 Digital Channels
MSOV134A
Oscilloscope
13 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Inductively Coupled Plasma
-
Inductively Coupled Plasma Techniques can be very powerful tools for detecting and analyzing trace and ultra-trace elements. Over the past years, ICP-MS has become the technique of choice in many analytical laboratories for providing the accurate and precise measurements needed for today’s demanding applications and for providing required lower limits of detection.
-
Product
ASN.1
-
Intuitive IDE • Speed • Compact Size • BER, CER, DER, PER, CPER, OER, COER, XER, CXER, E-XER, and JSON Support •True ASN.1 2021, 2015, 2008, 2002, 1997, 1990 Capable • Quality Tracing • Precise Error Messages • Multi-Threading • Automatic Encoding/Decoding • Partial Decoding • Dynamic Runtime Options • Interpretive ASN.1 API
-
Product
Microwave Digestion
-
Superior trace elemental analysis begins with outstanding sample preparation. With over 40 years of experience, Anton Paar strives to make microwave digestion easier and more convenient than ever before – thanks to sophisticated instrument and vessel concepts, state-of-the-art sensor technology, and the highest safety standards. Anton Paar offers the broadest range of instruments for all kinds of applications: microwave digestion systems Multiwave 7000 and Multiwave GO Plus, the microwave reaction platform Multiwave 5000 and conventionally heated Multicube 48.
-
Product
Elemental Analyzers
-
Bruker manufactures instruments for elemental analysis from 100% down to the sub-ppb trace level. Easy-to-use solution packages help customers in process and quality control to meet industry norms and standards including ASTM, DIN, ISO and FDA. Highest analytical accuracy and precision enable academic research from lab to field.
-
Product
Visual Fault Diagnostics and Repair System
ScanExpress Viewer
-
ScanExpress Viewer™ is a printed circuit board (PCB) CAD data & photograph visualization tool for boundary-scan test development, electronic manufacturing test, and product repair environments.When combined with ScanExpress ADO™ (Advanced Diagnostics Option) for detailed results from ScanExpress Runner™, ScanExpress Viewer displays fault coordinates and connected traces superimposed directly on a board photograph or CAD layout diagram for expedient repair.
-
Product
Mixed Signal Oscilloscope: 16 GHz, 4 Analog Plus 16 Digital Channels
MSOV164A
Oscilloscope
16 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
JTAG USB Controller
NetUSB-1149.1/E
Controller
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
Product
TX Ranger
4405200
-
The TX Ranger is a hand-held Time Domain Reflectometer (cable fault locator) with a first range of 2.5 meters combined with a 1.3 Nano second pulse width gives a blind zone of only 5 cm, it makes this the ideal product for fault location on short cable assemblies and harnesses. Small and intermittent faults can be easily identified by using the selectable gain control allowing trace amplification of up to 7 times and when set to scan lock mode the advanced noise reduction software may be selected allowing the user to select between 8,16 and 32-point trace averaging further enhancing the clarity of the trace by reducing electrical and environmental interference.
-
Product
Trace Oxygen Analyzer
GNL-IN121
-
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
GNL-IN121 is based on microprocessor, and keeps frequency current sensor as measuring point with intelligence, high accuracy and comprehensive function. It applies to the accurate measurement of oxygen concentration in 0~25.00% nitrogen- oxygen mixed gases. - See more at: http://en.ci-ele.com/8aedb8bf-ef48-4f8c-127a-797c939a6181/0e266f3f-134f-bfa1-4437-f6ee37fdb1dc.shtml#sthash.sNvnkmUs.dpuf
-
Product
Emulates Atmel T89C5111
FE-5111
-
* Emulates Atmel T89C5111 * 4K Code Memory * Real-Time Emulation and Trace * Frequency up to 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Locators
EZiSYSTEM xf-Series
-
The EZiSYSTEM xf-Series utility locating and tracing equipment makes locating buried utilities easy and efficient. The xf-Series locators have additional low frequencies enabling you to locate and trace utilities over longer distances and in congested environments. With an EZiCAT locator there is no need to manually adjust the sensitivity. With the unique Automatic Pinpointing feature, users can hold press the trigger and start locating.
-
Product
Digestion Systems
Tecator line
-
FOSS Tecator line Digestion systems are based on a digestion unit and a tube rack, allowing fully automated digestion for convenient, safe and flexible Kjeldahl analysis. Two way PC communication supports traceability and GLP. These versatile digestion systems are capable of handling eight, twenty or forty tubes in volumes of 100 ml, 250 ml or 400 ml dependent on chosen configuration. Parameters: Kjeldahl digestions, Chemical Oxygen Demand & other reflux chemistries, Trace metal analysis by AAS or ICP instruments. Sample types: Raw materials and finished products in Food, Feed, Agriculture and related matrices, Water & Wastewater and a wide range of industrial compounds.
-
Product
Martindale Abrasion and Pilling Tester
-
Sataton Instruments Technology CO., Ltd
By providing a defined load, a translational movement tracing a Lissajous figure and abrasive medium, martindale abrasion tester is professional designed for determining of the abrasion resistance of fabrics including specimen breakdown, mass loss and appearance change. The tester can also use to determine the resistance to pilling and surface change of textile fabrics. With accessories, the tester is to determine abrasion resistance of lining and insock for personal protective footwear. It is widely used to evaluate the properties of clothes fabrics, coating materials, wool fabrics, nonwovens and other special materials for protective equipment.
-
Product
Optical Spectrum Analyzers
-
An Optical Spectrum Analyzer (or OSA) is a precision instrument designed to measure and display the distribution of power of an optical source over a specified wavelength span. An OSA trace displays power in the vertical scale and the wavelength in the horizontal scale.
-
Product
Tone Generator
140BMC/6P
-
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
Product
Test System
4003 TLP+™
-
The Model 4002 TLP+™ test system was the first turn-key commercial TLP developed for the ESD industry and has remained the leader in the ESD square pulse testing field since this method was first introduced in 1989. This tester is the ultimate design and analysis tool for ESD protection circuits. It provides Pulse Curve Traces of circuit characteristics which simulate ESD tests. This allows you to see into a chip’s operation taking out the guesswork which speeds your design and minimizes lost time.
-
Product
Handheld RF Spectrum Analyzer With 1MHz To 1.3 Or 2.7GHz Bandwidth Options
PSA Series 3
-
1MHz to 1300MHz or 2700MHz frequency rangeResolution bandwidths of 300Hz to 10MHz 1:3:10-105dBm typical noise floor at -40dBm reference levelMeasurement in dBm or dBμV, mV or μWZero span mode with AM and FM audio demodulationTrace modes of normal, peak hold and trace averageLive, View (copy) and Reference traces in contrasting coloursTwin markers with readout of absolute & difference valuesSmart marker movement with selectable peak trackingFrequency counter with 10Hz ResolutionFrequency presets and independent state storageAuto-find automatically sets sweep parameters for the highest signal foundUnlimited storage for waveforms, set-ups and screensUser assignable file names, file stamping from real-time clockUSB interfaces for Flash drives and PC connectionComprehensive status and context sensitive help screensMore than 3 hours continuous operation from a chargeSmaller and lighter than other spectrum analyzers (weight only 0.58 kg)
-
Product
Fabric Drape Tester
TF118
-
TESTEX Testing Equipment Systems Ltd.
Fabric Drape Tester, to measure and calculate the coefficient of drape by tracing a shadow of the draped fabric on paper. Fabric Drape Tester complies with BS EN 9073, BS 5058, ERT 90-1, etc.
-
Product
Secondary Ion Mass Spectrometry (SIMS Analysis)
-
Rocky Mountain Laboratories, Inc.
Secondary ion mass spectroscopy is operated either in the dynamic mode (DSIMS) or the static mode (SSIMS). DSIMS is useful for profiling impurity and trace elements through films and interfaces. SSIMS is useful for characterizing polymeric materials and only measures the outermost molecular layer of a specimen.
-
Product
Cable ID & PoE Tester
PK-170 INNOTESTER PRO
-
INNOTESTER PRO combines the functions of a smart cable tester, network tester, port identifier and organizer with the capability to identify up to 100 cables run at a time, and 8 Test + ID remotes allows one person to test 8 cables run up to 600 meters. Tone mode, transmits 2 powerful tones for tracing inactive and active network cables on a Switch or HUB. More effectively tracing at patch panel, termination blocks or hidden within bundles.
