Temperature Controllers
Takes input from a temperature sensor and then sends a signal to control a heating or cooling element.
-
Product
Air Jet Erosion Tester
AJ-1000
-
The Rtec Instruments Air Jet Erosion Tester (AJ-1000) is a state-of-the-art solution for accurate air jet erosion testing of materials and coatings. Designed to perform repeated impact tests, the AJ-1000 directs a high-velocity jet of gas carrying abrasive particles onto the sample surface to precisely measure erosion rates. This advanced tester offers closed-loop temperature control up to 1000°C, enabling erosion studies under extreme environmental conditions. With the ability to vary abrasive particle type, shape, size, temperature, and impact velocity, the AJ-1000 provides a reliable way to rank and compare the erosion resistance of diverse materials and protective coatings.
-
Product
Digital Temperature Switch
TS2
-
Monitor and control temperature for heating and cooling applications with the Series TS2 Digital Temperature Switch. The Series TS2 offers twelve programmable functions to customize the unit to fit application requirements
-
Product
Temperature Control Battery Short Circuit Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL'S Temperature control battery short circuit test chamber is designed to comply with standard. According to the short-circuit test requirement, the short-circuit must be less than 5 mΩ to achieve maximum curren.
-
Product
Fluid Loss
-
Fluid Loss testers were designed to be as easy to use as possible, with clear and intuitive controls. Once the cement slurry or mud is placed into the test cell, a programmable temperature controller increases the temperature at the desired rate.
-
Product
Environmental Chamber/Stability Chamber - One Door Model
HC20
-
This is a Environmental test chamber/ Stability chamber/Laboratory incubator single door model capable of performing in wide temperature range(0°c to 70°c) with precise temperature control over the entire range.
-
Product
CryoPulse
-
Metis Instruments & Equipment NV
Measurements in up to 50 T environments. Cryogenic measurement environment with temperature control from 4K up to room temperature. Modular architecture with easy upgrades to higher energies & higher peak fields. Fast sample exchange possible. Large set of measuring probes for various applications
-
Product
Thermal Shock Test Chamber
-
observe the product characteristics and failure occurrences caused by different materials and their thermal expansion coefficients, thermal shock testing is subjected to the product. In thermal shock testing alternating high and low temperatures are fed in the chamber. WEIBER designs and manufactures customised THERMAL SHOCK CHAMBERS with separately controlled temperature zones (2 zone and 3 zone), liquid to liquid (2 zone) depending on configuration of the chamber chosen.
-
Product
Refractometer
RFM700-M
-
RFM700-M series refractometers are robust, low cost, fully automatic instruments that are ideally suited to the food, sugar and beverage industries but can now be used in many other non food applications where use of temperature control is not required. RFM700-M Series refractometers are robust, low cost, fully automatic instruments that are ideally suited to the food, sugar and beverage industries but can also be used in many other non-food applications where temperature control is not required, for example measuring sugar (Brix) concentrations in the food processing industry.
-
Product
Scalable Multi-Channel Active Thermal Control (ATC)
T-Core Thermal Control System
-
Cohu’s proprietary T-Core thermal system’s controller provides precise, multi-site temperature management of power dissipation ICs, such as graphic chips and CPUs, optimizing test yield.The T-Core thermal control system optimizes test yield at cold, ambient, and hot temperatures and offers better than +/- 1°C accuracy with response speeds of >125°C/sec. The system’s flexibility to control air, liquid, and refrigerant based thermal heads gives semiconductor manufacturers excellent temperature control capability for high volume manufacturing.
-
Product
Temperature Sensors
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s Thermistor Temperature Sensors are used as a temperature detector for temperature control or temperature indication of heating parts for automobiles and industrial equipment. Due to its sealed construction and high vibration resistance, it has high precision in temperature detection. Various types are available in accordance with application.
-
Product
cRIO-9068, 667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, Zynq-7020 FPGA, Extended Temperature, 8-Slot CompactRIO Controller
782663-02
Controller
667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, Zynq-7020 FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9068 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. The cRIO-9068 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, one USB host, and three RS-232 serial. Additionally, the cRIO-9068 supports an extended operating temperature range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
cRIO-9058, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller
787880-01
Controller
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9058 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with LabVIEW. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Temperature Controllers
-
Represents our dual-display solution in the basic temperature controller segment.
-
Product
Heating Incubator
-
Shanghai Selon Scientific Instrument Co. Ltd.
Essential tools in biomedical research that maintain a constant, controlled temperature for cell culture and microbiology studies.
-
Product
Temperature Controlled Air Bath
9300A
-
Measurements International Ltd.
The model 9300A series of Temperature Controlled Chambers is designed as a convenient and inexpensive way to maintain the temperature of air resistors in the calibration laboratory. It is large enough to house several standard air resistors and features two adjustable shelves to permit easy access to the standards. The shelves are easily removable.
-
Product
4 Point Probe Sheet Resistance/Resistivity Measurement with Temperature Controled System
TCR-600
-
*Controlled Thermo-chuck (room temperature～600℃/less than 20 minutes)*600C compatible probe head with 1mm linear*Controlled with vacuum sensor, digital thermo-meter, vacuum gauge and gas flow meter*Temperature measuring accuracy：±（0.5% + 1℃）
-
Product
Automated Thermostat Test System
-
*Transport mechanism moves thermostats to various temperature controlled locations.*Continuously monitored process status*PC controlled transport and measurements*Operator is shielded from 200 - 210 degree F hot water insertion baths*LabVIEW® test/process language
-
Product
Testwave Calibration
-
Testwave® LLC calibrates electronic, physical, & dimensional test equipment. Our Sparks facility includes a state-of-the-art temperature controlled calibration laboratory, which holds the temperature to within +/- 0.5°C. We send you recall notices before your equipment calibration expires, and if we don’t hear from you, we will call, to make sure you stay in compliance with your calibration requirements. Calibrations are performed at your facility, or at our Sparks Nevada laboratory.
-
Product
Reach-In Altitude Test Chamber
-
Weiber Altitude Test Chamber combine temperature and altitude to test basic components or subassemblies designed for use in a variety of industries. With altitude test chambers, user can control the temperature environment for testing while simulating various altitudes from site level to 10,400 meters (25kPa). Altitude testing may be continued without temperature control up to 600,000 meters (0.1 kPa).High Low Temperature Altitude Test Chamber is used to test temperature and low-pressure altitude conditions simultaneously. Two common applications of High Low Humidity Altitude Test Chamber are testing of avionics or other aerospace equipment to simulate actual conditions, and simulate high-altitude conditions found in mountainous regions or other regions. All models are factory tested, with an ergonomic and maintenance cum user-friendly design. These CE approved test chambers are created with multi-layered insulation with double vapour barrier is of low 'K' factor, high density and of non-hygroscopic in nature. Weiber test chamber are made in accordance with the international standard. Weiber Test Chambers are GMP complaints and are also ISO and NABL certified.
-
Product
Salt Spray Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Salt spray chamber is intended to use method of salt-spray corrosion to evaluate the performance of corrosion resistance of specimens to salt fog under the specified conditions. It is capable of simulating a locally salt mist environment in which the test piece is placed. There are different types of salt fog chambers including microprocessor digital version, touch-screen control version and compound version featuring temperature&humidity control and adjustment. widely applied to components and parts, electronics elements, metal materials etc.
-
Product
Environmental Chambers
KB Series
-
Darwin Chambers KB series Environmental Chambers are a top selling unit. It is quiet, easy to clean, highly reliable and ideal for laboratory use. Our environmental chamber offers hot gas bypass control of refrigeration and resistive heat to facilitate reliable, critical temperature and humidity control. All KB series environmental testing chamber models are designed to have a temperature range of 4-60o Celsius. Temperatures greater than 60o Celsius or lower than 4o Celsius can be achieved with optional upgrades to construction and components. All KB series environmental chambers come standard with Fuji’s PXG4 microprocessor, but we often install Watlow brand microprocessors for customers that need that brand or the capabilities it has. Unlike many proprietary controllers on the market, these controllers are available off the shelf and have been proven in tens of thousands of installations. All necessary functions are included in our Features section below. Many additional options are available both regarding control and recording of data (chart recorders and loggers)
-
Product
Environmental Test Chamber
-
The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip.The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1 and humidity is 0.1%R.HThe temperature sensor is platinum PT100 Ohms/MV resistor
-
Product
Power Switching Devices
-
Watlow Electric Manufacturing Company
Watlow solid state power switching devices complement the rapid switching required by PID temperature controllers and help deliver optimum system performance and service life. They are available in 1-phase and 3-phase/2-leg and 3-leg configurations, feature touch-safe terminations, input indicators, zero-cross, random or phase-angle fire options, ratings from 18 to 1,000 amperes and agency approvals including CE and UL® 508. Various configurations offer short circuit current ratings (SCCR) of 200,000 amperes, extensive system and heater diagnostic capabilities, heater bake out, integrated heat sinks, on-board fuses, RoHS compliance and serial communications.
-
Product
Stimulus Test Cell
HA7200
-
The HA7200 enables these improvements by providing high-speed, high-accuracy temperature and pressure test for automotive sensor R&D and production. Advantest’s proprietary temperature control technology delivers an optimized test solution for high-spec pressure sensors across a broad range of temperatures, in the automotive industry and beyond.
-
Product
Stability and Shelf Life Test Chambers / Rooms
-
Steady state environmental temperature and humidity walk in rooms for pharmaceutical, medical, electronics, personal care, research and development and consumer products applications. Meets all ICH guidelines. Flexible sizes. For stability and shelf life testing, package testing, accelerated aging, drying, burn in, reliability testing, controlled temperature storage, incubation, and cold room applications.
-
Product
Precision A/D Converters
-
Renesas offers both low-noise high-precision analog-to-digital converters (ADCs) for near-DC measurement applications such as weigh scales and temperature controllers, and high-speed precision ADCs and digital-to-analog converters (DACs) for classic industrial process control and instrumentation applications.
-
Product
Climate Control Test Chamber
-
ACMAS's Climate Test Chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. ACMAS Thermal Cyclic Chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperature ramp control. This chamber is also known as Climatic Test Chamber and Climate Controlled Test Chamber.
-
Product
Testing Machine For Rubber Vibration Isolators
-
This instrument can measure and process the data of spring constants, damping coefficients and loss factors of viscoelastic materials from static status to high cycles up to 300 MHz. The thermostatic chamber permits testing in controlled temperature environments.
-
Product
Bench Power Supply, Linear, Programmable, 1 Output, 0 V, 60 V, 0 A, 2 A
72-2715
-
The 72-2715 from Tenma is a single channel programmable bench power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +30mV (voltage), ≤0.5% +5mA
-
Product
Stability Chambers
-
Lunaire Environmental is a leading manufacturer of steady state and shelf life testing chambers and walk-in rooms which provide constant climate testing and meet ICH guidelines. These steady state chambers and rooms are perfect for long-term material testing on packaged products in controlled temperature storage. Lunaire steady state climatic test chambers are also ideal for research facilities and laboratories because they simulate wide range of temperature, and temperature and humidity environments. Click here for an overview brochure on Tenney and Lunaire equipment offerings.
