-
Product
CDN - Coupling / Decoupling Networks
-
The Coupling- / Decoupling Networks are used to inject common mode disturbances to Equipment under Test (EuT). Further the CDNs provide sufficient decoupling between Auxiliary Equipment (AE) and disturbance signal. The requirements for CDN and their application are described in the standard IEC 61000-4-6 (Immunity to conducted disturbances, induced by radio-frequency fields). CDNs have a common mode impedance of 150 Ohm and are available for a multitude of cable types and connectors.
-
Product
Custom Solar Simulation
-
Atlas Material Testing Solutions
Solar heat load effects are critical with respect to product functionality, operational performance, thermal management, noise and dimensional stability. Therefore, any new product made from different materials and components should be tested under solar environmental conditions representative of those locations in which it will exist - anywhere ranging from the heat of the Australian Outback to the frigid climate of arctic regions.
-
Product
ESD - Simulator
SESD 216
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
Home Network Analyser
microVB
-
The microVB is a breakthrough in both form-factor and functionality for real-time analysis of customer home network performance. This unobtrusive device provides deep packet inspection and end-to-end visibility in broadcast quality media delivery over any IP based infrastructure including OTT media in unmanaged networks.
-
Product
Monitoring & Simulation
-
ETAP Power System Monitoring & Simulation (PSMS) is at the heart of the ETAP Real-Time power management system. Power System Monitoring & Simulation is the smart choice for both small and large electrical utility systems, generation plants, industrial sites, manufacturing facilities, and off-shore oil platforms.
-
Product
Dynamic Test Board Vehicle Simulator
DTB
-
The Dynamic Test Board vehicle simulator range enhances functional testing by allowing greater test depth before the prototyping stage.
-
Product
Network Analysers
-
DIN 96x96 ultra compact version, only 39 mm depthFully bi-directional four quadrants measurements for all energies and powersMain electrical parameters measured and displayed for a cost-effective consumption analysisVersion for 1 or 5A CT and for direct connection up to 6APossibility to connect by PTUp to 8 MB for data recording (ENH version)Possibility to record all energy counters (ENH version)Up to 24 parameters selectable among real time measurements for MIN/AVG/MAX recording (ENH version)MODBUS RTU/ASCII communication by RS485 port or MODBUS TCP communication by Ethernet portPossibility to manage the instrument in remote mode by WintoolNET software or by Web server interface2 digital outputs, 1 digital input, 1 analog output (optional)
-
Product
FPGA Simulation
Active-HDL
-
Active-HDL™ is a Windows® based, integrated FPGA Design Creation and Simulation solution for team-based environments. Active-HDL’s Integrated Design Environment (IDE) includes a full HDL and graphical design tool suite and RTL/gate-level mixed-language simulator for rapid deployment and verification of FPGA designs.
-
Product
Simulators (Gen II)
J1939
-
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
Product
Vector Network Analyzer
MVNA-8-350
-
MVNA-8-350 is a vector network analyzer (VNA), an instrument which measures the complex, or vector, impedance (a real and an imaginary part of the impedance or an amplitude and a phase of the microwaves) in the millimeter and sub-millimeter frequency domain. It covers the frequency range from 8 GHz up to 1 THz.
-
Product
IOT Circuits and Networks
-
To understand the basic theory of internet of things (IOT) system.Design and implementation of sensor circuit.Ability to research and to develop the sensor circuit.Familiar with the applications of high accuracy sensor circuit.
-
Product
Vector Network Analyzer Leasing Option
-
Companies in the United States can now lease a CMT VNA from Leasing Corporation of America. Leasing is a great choice for organizations that may not want to spend capital budget up front since lease payments are an operating expense. Choose from 2, 3, 4, and 5-year options. Pay as you use the VNA, with a fixed monthly payment and a 90-day deferred payment option. At the conclusion of the leasing period the equipment can be bought out for $1.00 plus a lease termination fee of $99.00.
-
Product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
-
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
Product
4-Quadrant Power Amplifier For Simulation Applicaton
PAV20000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Network Management
Multi Restore
-
MULTI RESTORE – Safe, temporary connection from generator to residential customers
-
Product
TriSOL Large Area Solar Simulators
-
OAI has designed and engineered for large area markets Class AAA, ABA, or ACA Solar simulators with the same performance , quality, and reliability as our other solar simulator models. These large area solar simulators are available in several models.
-
Product
PCB Simulation Solutions for High-Performance Designs
HyperLynx
-
HyperLynx® offers a complete suite of analysis and verification software that meets the needs of PCB engineers at any point in the board design flow. Easy to use and integrate into your flow, HyperLynx equips PCB engineers to efficiently analyze, solve and verify critical requirements to avoid costly re-spins. Achieve greater innovation, faster time-to-market and decreased costs with HyperLynx.
-
Product
Network Surveillance System
-
The network backbone contains a wealth of information that can be monitored and collected to support diagnostic, troubleshooting, and fraud prevention activities. Surveillance of network characteristics is becoming more important than ever before. Few important aspects of network surveillance include, Performance Monitoring, Security, Fraud Prevention, Physical Layer monitoring, Billing Verification, Remote Protocol Analysis, Failure Prediction, Traffic Engineering, Call Quality Monitoring and Troubleshooting.
-
Product
Software Adaptive Modeling & Simulation of Nanosystems
SAMSON
-
SAMSON is the quickly growing platform for integrated molecular design. SAMSON's goal is to make it faster for everyone to design drugs, materials and nanosystems. For fun, or to build a better tomorrow through science and innovation in medicine, energy, materials, electronics, education, and more. SAMSON is available on all major operating systems.
-
Product
Mobile Network Monitor
-
Qosmotec Software Solutions GmbH
MVNOs and MVNEs as well as network operators themselves take advantage of LTS as a monitoring tool for the live network that detects and alarms about any performance degradations or outages. The LTS Mobile Network Monitor reports any inconsistencies immediately in form of an e-mail alarm or via SNMP traps. KPIs obtained by the system can also be queried at any time via SNMP, so that testers are permanently aware of the availability, reliability, quality, and integrity of the mobile network services from the subscribers’ point of view.
-
Product
MIMIC® Redfish Simulator
-
The MIMIC Redfish Simulator, the industry's first integrated simulation tool supporting Redfish, allows developers to perform real world, integrated device simulations. MIMIC simulates thousands of Redfish-capable devices. MIMIC allows suppliers of Redfish devices and applications to design, develop and test their products in a virtual and scalable network environment, assuring customers that their applications will be able to handle the scales of messages and different types of requests to work properly when deployed across heterogeneous environments.
-
Product
Radar Simulation 3.0
RADSIM
-
RADSIM provides the fidelity and flexibility of a phototexture-based digital radar landmass simulation (DRLMS) system. It uses Leidos-developed core radar simulation technology and can produce a very high-fidelity geo-specific or generic, simulated real-time synthetic aperture radar (SAR), Doppler beam sharpening (DBS), and real beam imagery to less than one-meter resolution.
-
Product
Streamline Vector Network Analyzer, 9 KHz To 9 GHz, 2-port
P9372B
-
Compact, faceless, vector network analyzer (VNA). Affordable full two-port VNA which dramatically reduces your size of test. Up to 9 GHz.
-
Product
1U Rackmount Network Appliance Platform
NA591
-
The NA591 is an advanced 1U rackmount network appliance platform with a maximum of thirty-four LAN ports. This high-performance network appliance system is powered by the Intel® Xeon® E-2200 and 9th/8th gen Intel® Core™ i7/i5/i3 processors with the Intel® C246 chipset. The NA591 comes with four expandable LAN module slots that support 1GbE/10GbE/25GbE/40GbE/Fiber/Copper/LAN Bypass interfaces, greatly enhancing its flexibility and scalability. This scalable 1U network appliance platform delivers security, stability and reliability for VPN, firewall, network bandwidth controller, WAN accelerator and surveillance system applications. This outstanding network security appliance features Intelligent Platform Management Interface (IPMI) to allow administrators to monitor system health and manage systems. Trusted Platform Module (TPM) is supported to bolster hardware-based data protection. Moreover, it features latch-type LAN Bypass functions for fail-over option as well as featuring BIOS console redirection. The NA591 is an ideal platform for network security, cloud computing and data centers applications.
-
Product
Power System Simulator
F6150e
-
This power system simulator performs the simplest through the most complex tests. Meeting all your protective relay testing needs, the F6150e is available in different configurations.
-
Product
Hot Socket Simulator
Hot Socket Simulator
-
The new TESCO Hot Socket Simulator gives you the ability to investigate meter failure issues related to hot socket phenomenon. The Simulator is equipped with one 2S meter socket with four jaws, one of which is the heated jaw. The arcing/heating apparatus can be moved to any of the four jaws (jaw 1 is the standard). Additional arcing/heating elements can be provided as an option for multiple hot jaws on the existing socket.
-
Product
End-to-End Network Monitoring
OSIX
-
Network monitoring with tracing and troubleshooting capabilities to achieve first-class customer experience and to proactively prevent network and service quality degradation. OSIX Monitoring enables Communication Service Providers (CSPs) to detect and resolve network issues or poor performance before end-customers are affected.
-
Product
SpO2 Simulator Pulse Oximeter Tester
OX-2 OxSim Flex®
-
The STANDARD OxSim Flex SpO2 Simulator (Pulse Oximeter Tester) provides flexible control of all your simulations. With Masimo rainbow SET® compatibility and an OLED color display, the unit automatically detects the manufacturer of pulse oximeter.
-
Product
Device Networking
-
Offers complete control of how and when the application can discover, connect, disconnect, and get status from the USB device across the network.By integrating the SDK, you can create your own user interface and make it work seamlessly with your application.The SDK supports searching device servers on the network.Supports getting information and status from the USB device server.
-
Product
CPCIe (PXIe) Module
ACS-FC-3U-2
-
The ACS-FC-3U-2 is AIM’s high performance CPCIe (PXIe) module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The ACS-FC-3U-2 is a powerful State-of-the-Art 4-lane CPCIe 2.0 compliant CPCIe board.
