Microprocessor
an IC processing logic operations to fulfill an end. Also known as: CPU
See Also: Computer, Raspberry Pi, SBC, CPU
-
Product
Microprocessorized Instrument
MP-100
-
Mobile meter designed to measuring the magnetic permeability lower as 3 and allows to control the elements with small overall dimensions and the elements with complex shapes as well as it allows the evaluations of heterogeneity of the elements with big overall dimensions. The meter contain the measurements memory and all obtained date could be display on LCD. The meter contain also RS232 interface which allow the data transmittion to PC.
-
Product
2 Port 100GbE Single Host Network Mezzanine Card
NMC-6002FD
-
Single host NIC solution by using Mellanox ConnectX-5, Overlay networks support: VxLAN & NVGRE. CPU offload: TSO, LRO, GRO, Jumbo frame support (9.6KB) Compatible with FWA-6520, 5020, 6170, 6070 & 5070.
-
Product
Conduction Cooled VPX Interface Board with PCI Express Host Interface
EXC-8000ccVPX
-
The EXC-8000ccVPX is part of the 8000 family of multiprotocol carrier boards. This conduction cooled VPX interface board has a PCI Express host interface and can support up to four independent removable modules and 10 on-board Discrete channels. Each removable module can be any of the 8000 family modules.The EXC-8000ccVPX supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from the board, with much less CPU overhead than when not using DMA.The EXC-8000ccVPX is supplied with C drivers, including source code. Mating connector provided for I/O connection.
-
Product
Vehicle Battery Charger
6435A
-
Peaceful Thriving Enterprise Co Ltd
This charger use microprocessor to monitor the charging process. Therefore it is a smart charger with protection of reverse connection, over-voltage, over-current, short circuit and over-charging. It has wide working temperature and it has IP54 protection. Cigarette lighter connector and alligator clip can be replaced for power source.
-
Product
LAN Router
BB-SR30019110-SWH
-
SmartFlex, Global, 5x Ethernet, Wi-Fi, PoE PD, Plastic, Without Accessories. VPN, Multiple LAN/WAN configuration, DIN rail mounting. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
FireBird CoaXPress Frame Grabber (Dual CXP-6)
AS-FBD-2XCXP6-2PE8
-
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
Product
XMC Gigabit Ethernet Boards
-
High-performance 1/10-Gigabit Ethernet interface solutions for real-time and COTS data streaming applications. XMC modules provide a rugged, embedded computing platform for high-speed data communication in defense, aerospace, and industrial systems. Implementing a TCP offload engine (TOE processor) fully in hardware relieves the CPU from TCP/IP overhead and frees it to perform other tasks.
-
Product
Hybridization Oven
REXMED ROV-200
-
MOD. ROV-200, AC 110/230V, Plug type: , Hybridization oven, HS CODE: 841780, UNCCS CODE: 484352, UMDNS CODE: 14410, Main construction: powder coated steel and SS304, Controller: Microprocessor based PID controller, water proof keypad with timer, ˚C/PV and ˚C/SV display and setting, Timer: 9999/min, 9999/hr, Timer has DELAY_ON and DELAY_OFF function and at the end of operation audio and visual warning, Working range: Ambient +5˚C~85˚C, Stability at 37˚C: ±0.1˚C, Sensor: PT 100Ω, Temperature audio and visual warning for AL-H and AL-L and OFS correction setting, Heater: 1KW, Shaking timer: 999/min, 999/hr, shaking timer can be set in second, minute or hour function and at the end of operation audio and visual warning, Motor: Noiseless powerful brushless induction motor 15W, Rotation: 5~60rpm adjustable, Rotator: for 8pcs(optional), Reciprocal: 5~60rpm adjustable, Platform: L30 X W18cm(optional), Rocker: 5~60rpm adjustable, Platform: L29 X W22.5cm(optional), Chamber: L35 X W25 X H25cm, Capacity: 21.9L, chamber with glass viewing window, Optional: Rotator for 8pcs X 1set, reciprocal platform (L30 X W18cm) X 1set, rocker platform (L29 X W22.5cm) X 1set
-
Product
Laser Type PM Sensor
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s Laser Type Particulate Matter Sensor is comprised of an on-board microprocessor, micro-fan, and laser diode. This PM Sensor has been programmed so that the fan will operate based on the amount of particle dust surrounding the laser diode so that the overall lifespan or usefulness of the Sensor can be extended much longer than its’ average commercially available equivalent.
-
Product
Medical Box PC Featuring The 12th/13th/14th Gen Intel® Core™ I3/i5/i7/i9 Processors, With Support For MXM GPU Module With Embedded NVIDIA RTX GPU And Thunderbolt™ 4 Port
MLB-3102 with NVIDIA MXM GPU
Industrial Computer
- ADLINK MXM graphics module support (type A/B, up to 120W TDP based on power supply)- 12th/13th/14th Gen Intel® Core™ i3/i5/i7/i9, Celeron® processor- Dual SODIMM for up to 64GB DDR5 non-ECC memory (depending on CPU)- 1x HDMI 2.0, 5x DisplayPort (1 from CPU, 4 from MXM)- 1x M.2 E-key supporting 1630 or 2230 for Wi-Fi/Bluetooth module, 1x M.2 M-key supporting 2242 or 2280 for SATA/PCIe storage module, 1x M.2 M-key supporting 2242 or 2280 for NVMe & frame grabber- Reliable Molex 24V DC-in connector- 2x 2.5GbE Intel® I225-LM Ethernet Controller- 2x PCIe Gen 3 x4 expansion slot for full-height, half-length add-on card, each slot is 25W power budget and additional Molex 4-pin power cable (12V/1.5A and 5V/2A) support
-
Product
Erbium Doped Amplifier
AEDFA-FTTH
-
Amonics FTTH EDFAs inherit the reliable design of Amonics's optical amplifier technology. They exhibit high output power, high gain with very low noise, and are ideal for FTTH network amplification. Integrated CWDM splitters are available to enable routing of 1310nm and 1490nm data streams from OLT to ONU through EDFAs. The turnkey rackmount EDFAs provide microprocessor controlled alarms and status indicators. An integrated Ethernet TCP-IP computer interface enables easy control, diagnostic functions and data acquisition.
-
Product
Earth Resistance Meter
EM 4058
-
earth tester is a digital, microprocessor controlled instrument that allows to measure the earth resistance and ground resistivity (using Wenner´s method), as well as to detect parasitic voltages present in the ground. This instrument is suitable to measure earth systems in power substations, industries, distribution networks, etc., according to IEC 61557-5.
-
Product
cRIO-9058, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller
787880-01
Controller
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9058 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with LabVIEW. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
PXI CAN Interface Module
CAN Interface
PXI CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate, Low-Speed/Fault Tolerant, and/or Single Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from FIBEX and DBC files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Product
Power Bus
MS 1606
-
The PowerBus is used to service printed circuit boards, instruments and systems, which has Micro controller / Microprocessor. The PowerBus has RS232 Communication for PC interface. The PowerBus connects to the UUT through the microprocessor / micro controller socket. The UUTs microprocessor / micro controller is removed from the UUT and it is replaced by the PowerBus. The Power Bus adapts microprocessor specific function as pin layouts, status / control function, interrupt handling, timing and memory and I / O addressability.
-
Product
Osprey / DX Co-Processor
9687
-
Double+ speed Osprey Co-Processor. Occupies one ISA/EISA PC slot. Writable control store, FPGA implementation of PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes FPJ11® compatible hardware floating point. Performance equivalent twice the DCJ-11® and 100%; of FPJ-11. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. This card is used for Osprey/PC applications where all applicable I/O devices are emulated on the PC by Osprey software. Includes standard environment support for MS-DOS® V6.2.2. Windows/NT® environment support available.
-
Product
Light / Lux Meter, Calibrated w/D & U, 50000 lx, 100 lx, 4 %, 185 mm, 78 mm, 38 mm
72-7250 CAL DU
-
The 72-7250 CAL DU from Tenma is a digital light meter with RS232 capability. It has custom one-chip microprocessor LSI circuit which ensures high accuracy. The meter features 13mm (0.5”) super large LCD display with contrast adjustment for best viewing angle, data hold and auto power off. It records maximum, minimum and average readings with RECALL facility. The 72-7250 has RS-232 PC serial interface, user selectable lighting type (tungsten, fluorescent, sodium or mercury, daylight) and zero adjustment by push button. The meter operates from 9V battery.
-
Product
1-port CAN Bus Data Logger
CAN-Logger100
-
The CAN-Logger100 is a high-performance smart CAN bus data logger with one CAN port that can help collect data and process on a CAN bus network easier and quicker. The powerful CPU of the CAN-Logger devices provide the accurately time-stamp for each CAN message and support storage media like SD card or SDHC type flash to save CAN messages, which helps users easily analyze and diagnose the CAN Bus network. Providing great portability, the CAN-Logger100 is powered by USB interface or M12 connectors of CAN bus interface. The CAN-Logger100 device uses the standard USB HID driver of the Windows system.
-
Product
Temperature and humidity outdoor, indoor probe
T3110
-
Programmable temperature and humidity transmitter is equipped with temperature and relative humidity sensors. Measured values are also converted to other humidity interpretation - dew point temperature, absolute humidity, specific humidity, mixing ratio or specific enthalpy. Degrees Celsius and Fahrenheit are user selectable. Transmitter contains a microprocessor based control circuitry in a durable plastic case with connection terminals and sensors in a filter with stainless steel mesh. Humidity transmitters is equipped with two galvanic isolated 4-20mA outputs. Configuration of outputs and output range are user adjustable. Large dual line LCD for simultaneous display of T+RH or other humidity interpretation is an advantage. Display is possible to switch off. Computerized design ensures temperature compensation of the humidity sensor and fail indication. State-of-the-art capacitive polymer sensor ensures excellent calibration long term stability, inertia against water and condensation. Transmitters are designed for use in non-aggressive environment.
-
Product
Electronic Ballast Analyzer
WT3000
-
• It has 8 windows to display each parameter of input and output characteristics • Frequency response for testing input current up to 1MHz, suitable for precise testing of various kind of electronic ballast • WT3000 has expanding analysis for envelope wave. • Symmetry analysis for envelope wave’s crest factor of lamp current • Sampling at ultra-high speed, dynamic analysis single frequency curve, highest sampling frequency is up to 10MHz • Portable with built-in chip micro-processor, particular suitable for development and spot production • RS-232C standard interface can be connected to PC, English version software can run in WinXP or Win7
-
Product
6U VPX Board
VP62009
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62009 is a 6U VPX board based on Intel® Xeon® D-15xx processors, with more than 7-year life cycle. Supporting up to Intel® Xeon® D-1577 (16x 1.3GHz) processor, VP62009 is able to perform vector operation and floating point arithmetic that require high throughput. Besides, VP62009 supports Intel® Turbo Boost, with the processing speed of CPU up to 2.7GHz. The high-performance CPU and the Turbo Boost technology leave no worries for extra cost and complexity of system settings.VP62009 provides 2x 10 Gigabit Ethernet for VPX Data Plane communication, 2 x8 PCIe for VPX Expansion Plane communication, 4 GbE for VPX Control Plane communication. Rich data exchange interfaces on VP62009 make it easy to build box-level or system-level solutions.
-
Product
Underground Cable Fault Locator
KM-CFPL-620 /620B
-
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
Product
Opacity Monitor
DT1000
-
The Datatest Model 1000 is a microprocessor based EPA compliance opacity monitor. The microprocessor creates excellent stability and reliability plus the use of patented glass fiber optic technology in the stack components further enhances the performance. The Model 1000 is offered in a double pass Model 1000 MPD version or a single pass Model 1000 MPS (suitable for harsh applications).
-
Product
Spectro UV-Vis
UVD-2000RS
-
The Spectro 2000 RS is a microprocessor automation instrument with the highest technology. It is the ideal instrument for: Chemistry, biochemistry lab., analytical, medical, environment protection, agricultural, industry, universities and research
-
Product
Trusted Platform Module Compliant With TCG 1.2 / 2.0 Specification And TCG Software Stack 1.2 / 2.0 Via SPI Connector On CPU Card.
PCA-TPMSPI
-
Trusted platform module compliant with TCG 2.0 specification and TCG software stack 2.0 via SPI connector on CPU cardHardware based data protection solution for storage device encryption and decryptionDimensions (L x H) : 20 x 22 mm (0.79" x 0.87")Support Model: PCE-5033/5133
-
Product
CPCI Or PXI PCM & ARINC 717 Board
MS 1703
-
*Bus Interface - PXI / CPCI Bus*Microprocessor and FPGA design based Board*One Channel ARINC 717 Transmitter and Receiver*Generates all PCM telemetry signals like NRZ, Bi-Phase, Differential Bi-phase, DM signals*Used to test all types of PCM based telemetry equipments*Configurable output signals format (parity, word length, Minor, Major frame, Bit position)*User can configure the words and there positions in the frame*The word can be either a square / triangle wave data or constant data*1 MB Shared Memory for Data Storage*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Debug Probes
J-Link and J-Trace
-
SEGGER Microcontroller GmbH & Co. KG
SEGGER J-Links are the most widely used line of debug probes available today. They've been proven for more than 10 years with over 250,000 units sold, including OEM versions and on-board solutions. This popularity stems from the unparalleled performance, extensive feature set, large number of supported CPUs, and compatibility with all popular development environments.
-
Product
LAN Router
BB-SR30009120-SWH
-
SmartFlex, Global, 5x Ethernet, PoE PD, Metal, Without Accessories. VPN, Multiple LAN/WAN configuration, DIN rail mounting. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
Test Set For Instrument Transformer
-
This modern Test Set For Instrument Transformer is used for measuring relative errors of Instrument Voltage and Current Transformers. This is developed for reading out the unbalance of any bridge circuit. It also calculates the burden associated to the test sample. In addition to this, it further converts it to ratio and phase error values for presenting them on a LCD screen. With high-tech microprocessor controller, it ensures to provide quick and correct measurements.
-
Product
Multiple (8) Four Quadrant Power Source
PM0820
-
The PM0820 uses an onboard controller, which relieves the system CPU of performing many functions necessary for the module operation. The result is higher efficiency of the CPU and faster execution of the module commands.
