Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
783863-01
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Peeling Tester
BN-3
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3;Inspection standard: JB/T4279.6-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.0mm and below;High-end SCM control is used;Set arbitrarily the number of twist;LED would automatically display the number of twists;Twist counter performs accurate and reliable counting;High-strength steel scraper would complete sample scarping at once, easy to operate and use.
-
Product
20-Pin GMCT Cable, Male to Male, 10A, 2m
A020GMR-020GMR-0B200
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
Gateway
CODA-4580
-
Hitron Americas Technologies Inc.
The CODA-4580 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface. The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. The CODA-4580 supports full IPv4 routing features, as well as full support for IPv6 routing and firewall. The CODA-4580 supports both DSLite as well as 6RD for different IPv6 deployment and transition strategies.
-
Product
PCI Bus Synchro - Resolver - LVDT I/O Cards
PCI Synchro
-
Computer Conversions Corporation
Proven "Whole" Std. ConvertersOptimized Thermal ManagementExternal Synchro AMP I/O100% Transformer Isolated I/OPermits 2 wire X/Y Stators(Air)No External Parts or Power RequiredReference Powered(NAVAL) Options10-16 BIT Resolution ProgrammableVirtually Indestructible Outputs1.2 to 4.5VA High Power ModelsMix/Match Input & Output TypesSimultaneous Fine/Coarse Transmit For Multispeed Outputs
-
Product
Multisystem Ignition Analyzer
TA500
-
The TA500''s unique and proprietary technology allows the user to perform quick and reliable diagnostics of non-starts, misfires, fouled up or damaged spark plugs and/or spark plug wires, by comparing digital read-outs of the spark plug voltage and spark burn time between cylinders on engines using Coil on Plug, Coil near Plug, conventional distributor/ignition coil, DIS (Distributor-less) or waste spark and magneto technologies.
-
Product
SQUID Series Arrays
-
The SQUID series arrays are ideal for readout of TES sensors or as amplifier stage for discrete two-stage applications. Integrated bias resistors for TES or two-stage applications reduce wiring complexity. Various arrays with input inductances of 3 to 6 nH, input sensitivities of 17 to 23 µA/Phi0, and a current noise between 5 and 10 pA/sqrt(Hz) @ 4 K are available.
-
Product
PICMG 2.16 Type 12H Rackmount - 12U
12H21FDXC8Y4VQFX
-
High quality 19" rackmount chassis platform consisting of pre-galvanized steel enclosures, PICMIG 2.16 or 2.17 backplane, power supply, redundant push/pull cooling system and AC/DC power components. Assembled, wired and tested prior to shipment.
-
Product
Cable Assembly, Receiver, TriPaddle, 72", 200 Pin Male LFH, M3 jackscrews
540105040505
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 72", refer to drawing for wire list, M3 jackscrews
-
Product
Internal Rotary Encoders
-
Rotary encoders for internal installation within motors feature up to an IP40 rating and permit high operating temperatures. The wide variety of models can be used to adapt a motor to a wide range of applications, thus minimizing installation work and wiring.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 0.5m
A068SFR-C-6A050
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Universal II Level System
-
The Universal II is a two wire level transmitter that eliminates the need for line power in the field and saves costs for additional hardware. It provides reliable level measurements in all kinds of process liquids, slurries, granulars and interfaces.
-
Product
Cable Assembly 44-Pin D-Type Male to Unterminated With Cut Ends, 0.5m
A044HM5-C-0A050
Cable Assembly
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks.
-
Product
Compression Test Apparatus
CT-20 C
-
Is designed to perform tests specified in many standards where resistance of insulating materials to elevated operating temperatures is to be determined. It is used to test insulation materials used in Electrical Appliances, Electrical wiring accessories, luminaires, motors, connectors, etc. The test ensures that external parts of insulating material, the deterioration of which might cause the appliance to fail to comply with the relevant standards, are sufficiently resistant to heat
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Ferrules, 2m
40-972-015-2m-FU
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
2.5mm Test Wire Test Probe Pin
CX-3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test wire test probe pin 1.Application: Used to verify the protection of persons against access to hazardous parts. Also used to verify the protection against access with a tool.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 1m HV, Exit Towards Pin 1
A050DM5-T-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
PCB Connectors
CMD Series
-
Smiths Interconnect's versatile, high density CMD connector solution for board to board and wire to board with built in coding and keying as well as ESA qualification
-
Product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
Amplifier
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
Cable Length Meters
CLM-1000
-
*Measures these AWG wire gages: 18, 16, 14, 12, 10, 8, 6,4, 2 , 1/0, 2/0, 3/0, 4/0*Measures these kcmil wire sizes: 250, 350, 400, 500, 600, 750, 1000*Eight user-programmable settings for other gages*Powered by (6) 1.5V AA batteries*Replacement calibration rods (pair) available as CLM-ROD, UPC 02721*Replacement Kelvin clips (pair) available as CLM-CLIPS, UPC 02722*Feet
-
Product
Vertical Hinged Mounting Frame, ICon, 5U, 3 Positions
310113463
Mounting Frame
The 5U Vertical hinged Mounting Frame mounts to standard 19" racks and hinges open to allow access to wiring between the instruments and VPC Receiver. The 3 cutouts are spaced evenly across the panel. iCon cover plate sold separately (310 113 467).
-
Product
Ethernet to Relay Interface Boards
Model 8064 OEM
-
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
Product
Solid-State High Power Amplifier 18 - 26.5 GHz
AMP4065LC-2
-
Exodus Advanced Communications
Designed for EMI/RFI, lab, and general communication applications. Exodus Broadband SSPA product feature GaN, GaAsFET discrete and Chip & Wire Hybrid technologies covering one octave through decades frequency ranges from Operating Frequency Range 18.0-26.5 GHz.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Cut Ends, 1m
A015DM5-C-0A100
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Tone Amplifier And Tone Generator Set
AM5/TG5xs
-
The New Tone & Amp Set are state of the Art Testers offering touch button technology, visual qTrace (quick trace) as well as audio tracer tone technology providing accurate wire location, high output volume and sensitivity, tone tracker functionality, Visual/Audible indication of Digital Traffic, filtered amplification with multiple volume levels and two normal tones and four tonetracker tones with constant and variable interrupt rates, short detection and indication, capacitive output connection, Quick change battery and low battery indication in New custom designed High impact resistance enclosures, fully sealed to IP67.
-
Product
80-1000V AC Non-Contact Voltage Tester
5226
-
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 80V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
Product
High Voltage Switching Matrixes -15KV – 48Ch
H730035
Matrix Switch Module
Fast ATE technology: Modular, scalable and top flexible approach Minimum wiring and easy maintenance; LabVIEW drivers
-
Product
Tiny AVR Programmer
-
The ATtiny45 and 85 are a couple of really cool little MCUs but did you know you can program them in Arduino? That's right, now you can shrink your Arduino projects down to "tiny size" by moving your code straight over to these small but capable ICs. The standard method for programming the ATtiny ICs involves a breadboard, lots of jumper wires and a hardware programmer, but David Mellis over at MIT Media Lab has simplified the process by laying out this handy USB programmer.
-
Product
Weather Resistant Surge Protector for RS485 Control & 12VDC Power Lines
SP-RS485-12V-O
-
Ideal for applications such as video surveillance cameras and access control. Protects sensors running on 22 AWG 2-wire sensor cables or 12VDC power lines against the effects of electrostatic discharge, faulty wiring and lightning. RS485 protection: Stage 1 clamping voltage: ±90V; Stage 2 resistance: 3.3 Ohms; Stage 3 clamping voltage: ±7.5V. 12VDC power lines protection: Stage 1 clamping voltage: ±90V; Stage 2 current rating: 3A; Stage 3: 12V TVS (transient voltage suppression) diode. Screw terminal pairs for RS485 and 12VDC power lines protection. Will also protect two single ended data, analog or control lines. Impact and weather resistant enclosure with locking hinged cover.
