Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
Product
78-Pin D-Type Male Breakout DIN Rail
40-967-078-M
Breakout Board
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
Product
SCSI CABLE TESTER
ST123
-
Continuity tests alone are not sufficient to qualify SCSI cable assemblies. Proper testing of SCSI cables must include a test for correct connection of twisted pairs and shielding. Continuity tests check only that wires are making connections on both ends of a cable.Twisted pairs in the cable must be matched with the correct SCSI signal pairs - otherwise, it is possible to have a SCSI signal (signal and ground pair) placed on wires that are not in the same physical twisted pair (see diagram at right). This will cause crosstalk with resultant SCSI errors.
-
Product
Intelligent and Unidirectional Scrape Tester
ZDG-25
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3Inspection standard: JB/T4279.9-2008Meet GB/T6109-2008 standard requirementsUsed to test the film scrap resistance of enamelled round wires with nominal conductor diameter above0.250mm;Application of SCM control，enter the weight value, operation will be completed automatically: put down the scraping rod, stop while film scratch, calculate and show the scraping force, raise the scraping rod, return to zero, sample rotates 120°and repeat the same operation, calculate and show the scraping force of three times and average scraping force.When film is scratched, film scraper would automatically stop scraping, with exposed conductor of sample＜3mmWith the advantages of high sensitivity, good repeatability, stable and reliable characteristics.
-
Product
Split type AC Current Transformer
CTF-100T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Wire stopper is equipped for the slipping protection.*The special connector is not necessary as the output terminals are provided.*Open circuit protection and nonflammable plastic material.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Ferrules
A078HF5-F-0A050
Cable Assembly
The A078HF5-F-0A050 is a A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit towards pin 1.
-
Product
RJ45 Replacement Port For XG2 Tester
#TXGPORT
-
*Easy field replacement*RJ45 port installs with two screws*No wiring required
-
Product
Strip-Line™ Socket with Bifurcated Contact Wire Wrap Pins
Series 0501
-
Strip-line Sockets with Bifurcated Contact Wire Wrap Pins. Features: For mounting liquid crystal displays and other high pin count or odd centered components. Available in several sizes with bifurcated contacts in wire wrap or solder tail pins. Consult Data Sheet No. 12008 for solder tail pins.
-
Product
Connector, 50-Pin SGMC, Female, 5A, Crimp Pin, Without Backshell
C050FFX-1CP-0A
SGMC Female Connector
This 50-pin SGMC connector is designed to allow users to directly terminate with crimp connections and is suitable for 22 AWG copper wire. Supplied without a backshell. Screwlocks are provided to secure the connector to its associated product.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44TEF
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
20-Pin GMCT Cable, Male to Male, 10A, 0.5m
A020GMR-020GMR-0B050
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 1m HV, Exit Away From Pin 1
40-970-050-1m-FF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Press Down Rods Bed of Nails Testers
RandHDPE HDPE Family
-
HDPE plastic plates for extra easy machine ability and upgradeability. Designed for Research & Development and Pre-Production where product engineering changes are a weekly issue. The primary design focus is easy upgradeability. In R&D and Preproduction, design changes can happen every week. This fixture unlike normal test fixtures was designed to be easily taken apart and updated. Disassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for machining, drilling and wiring updates.
-
Product
4-Pin Power D-Type Cable, Female to Female, 0.5m
40-970-404-0.5m-FF
Cable Assembly
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Ferrules, 1m, Screwlocks
A068SMR-F-6A100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
Wall Searching Metal Detector
HHB C
-
A Wall Searching Metal Detector, also known as a stud finder or wall scanner, is a tool used to locate hidden objects behind walls, such as metal pipes, electrical wires, and wooden studs.
-
Product
Professional Cable Tester
1EA560
-
Multifuncional tester with LCD display enables to show wire maps and combination of pairs and their lenghts. It also measure the lenght until the broken line / cable. It is suitable for CAT5, CAT5E, and CAT6 cables. With special interface is also suitable for testing of coaxial and telephone cables. It has special unit for testing of cable ends in the other room.
-
Product
192 X 4 / Dual 96 X 4, cPCI High Density Matrix Module
DP-cPCI-4149
-
Matrix switches are the most versatile type of switching system. Any input can be connected to any output, singly or in combination. A matrix switch simplifies the signal routing in an overall system, through reduced internal connection path.DP-cPCI-4149 offers ultra high density matrix in a single slot 6U sized cPCI module with flexibility to configure in the following ways:192 x 4 (Single- wire).Dual 96 x 4 (Single -wire).96 x 4 (Two-wire)DP-cPCI-4149 uses magnetically screened reed relays.
-
Product
Impulse Cable Tracer
Wayfind'r
-
The WAYFIND'R Impulse Cable Tracer was originally designed for electric utility use to accurately identify the route of buried secondary cables. Because the WAYFIND'R imposes an audio frequency signal on the cable, the signal is not induced into adjacent cables or pipes, eliminating false signals. The WAYFIND'R may also be used fro tracing indoor wiring and buried shielded primary cables.
-
Product
Superconductors & Metal Composites
-
Welcome to BEST, a leading manufacturer and developer of high-performance superconductor wire products and research instrumentation.
-
Product
50 GHz Micro Coax Contacts
-
VPC's 50 GHz micro coax contacts demonstrate outstanding RF performance from DC to 50 GHz. They offer the best density for higher frequency requirements, and can be used in micro coax modules for 90 Series systems and iSeries solutions. They are available in patchcords using Flex 405 high frequency wire. For questions regarding VPC 50 GHz solutions contact a Field Application Engineer.
-
Product
SparkFun Thermocouple Breakout
MAX31855K
-
The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the other (a 'hot' end and a 'cold' one). Once this is achieved, a voltage potential is formed and current flows. The SparkFun Thermocouple Breakout takes a standard Type-K thermocouple in one end, digitizes the temperature measured and sends that data out the other end via a SPI interface, thereby interpreting the data and translating it for you to read!
-
Product
22-Pin REDEL High Voltage Cable Assembly, Male to Unterminated, Cut Ends, 0.25A, 1m
A022KMR-C-HA100
Cable Assembly
This is a 1m long male to unterminated 22-Pin REDEL high voltage cable assembly with cut ends constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips are provided to secure the connector to associated product.
-
Product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
Relay Matrix Module
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m
A037DM5-T-0A050
Cable Assembly
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Modular System for Automated Quality Control
TEST-9110-VXI
-
The TEST-9110-VXI "Flight" system is a Russian modular system for automated quality control of harnesses and wiring. The system is built on the basis of the international VXI standard, and all its components are manufactured entirely in the Russian Federation by the Informtest holding. The advantages and simplicity of TEST-9110-VXI have already been appreciated by more than 50 leading Russian enterprises in various fields of production. Starting from 2007 and up to the present moment, “Polyot” is the most popular system of this class in Russia, which completely replaces similar import systems in its parameters.
-
Product
Environmental Test Probe, Temperature
72-8366
-
Simple thermocouple junction at the end of a 1m wire provides effective low cost ambient temperature measurement. It is suitable for measuring air temperature and may be placed in direct contact with hard surfaces. Type K thermocouple temperature probes are commonly used with all types of industrial temperature controls and measurement equipment, and are compatible with Tenma handheld thermometers and digital multimeters that include temperature function. All are terminated with standard Type K plugs.
-
Product
Safety Light Curtains
-
*Type 4 (IEC 61496) safety light curtains at Type 2 pricing*Reliable protection of hazardous areas*Short and long range selectable via wiring*No dead space when mounted in in L shape*Industry standard M12 connection for simple wiring
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Ferrules, 1m, 45º
A1604F5-F-0A100
Cable Assembly
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
