Interface Test Adapters
Interface Test Adapter; Interface Connector Adapter: Interface Device Also known as: ITA
See Also: Test Adapters, Interface Adapters, ITA
-
product
VTAC, Patchcord, ITA, 36", VTAC, HDMI, Double Ended
7-141891141-036
VTAC, Patchcord, ITA, 36", VTAC, HDMI, Double Ended
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 22-24 AWG
610138109
Primary mating contact 610138216. (May mate with other ITA contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2-ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.24
-
product
Tool, Kit, 75 Ohm Coax, ITA, Cable Install
910102107
Consists of 2 tools for installing cabling into the contact. Crimp Tool and Locator for center contact and Hex Crimp Tool for outer shield (p/n# 910104139).
-
product
Receiver, 9025, 25 Module, Slide Mount, Telescopic Handle - Left Side
310104498
The 9025 is a 25 module receiver designed to fit into a standard 19" rack. This model is equipped with a telescopic handle on the left side. This handle is designed to rest flush against the side of the receiver as a standard handle, or can be extended out to the left up to 3" to accommodate a larger ITA enclosure or other obstruction that may prevent normal handle operation/ engagement.As with the standard 9025, a microswitch is included. Mounting flanges and an instrument bracket are also included for slide mounting. A slide kit is required, but not included. See 9025 procedure sheet/ user manual for instructions on choosing the correct slide kit length for your test rack. *Please note: Consult procedure sheet/user manual for information regarding slight slide mechanism bracket protrusion downward into next U height on test rack on both sides of receiver.
-
product
Keying Pin Kit, ISeries, Receiver And ITA
310113461
The iSeries keying pin kit includes a set of two hex keys. One hex key will allow 6 different options and two can provide 36 different keying options. The keying kit provides a way to isolate your connectors to prevent operational mismatch.
-
product
Receiver, ICon, Reverse Module Configuration For ICon ITA Modules, With Protective Cover
310123103
Receiver, iCon, Reverse Module Configuration for iCon ITA Modules, with Protective Cover
-
product
Micro Coax/Micro Power, Module Insert, ITA, i2 MX, 15 Position
510144009
Micro Coax/Micro Power, Module Insert, ITA, i2 MX, 15 Position.
-
product
ITA, I1, With Protective Cover
410128101
The i1 ITA's small width and inboard handle increase the side to side stackability. The U-shaped cable clamp allows modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 1.07 in. The removable cover allows easy access to wiring for maintenance and probing. Protective Cover included.
-
product
Micro Coax, Contact, Receiver, RG178
610140102
Primary mating contact 610141102. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG178Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle, (5 Amp), 26 AWG Twisted Pair White/Black (1.5 Amp)
7-123426000-036
Signal, Patchcord, ITA, 36", QuadraPaddle, (5 Amp), 26 AWG Twisted Pair White/Black (1.5 Amp).
-
product
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps)
7-241914000-036
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps).
-
product
Tool, Crimp, 75 Ohm Coax, Receiver and ITA, Hex Crimp
910104139
Used to crimp the ferrule on 75 Ohm contacts. Also included in tool kit p/n # 910102107.
-
product
ITA, 9025, 25 Module, Single Tier
410104111
Supports a maximum load of 787 lbs to achieve .030" total deflection.
-
product
VTAC, Patchcord, ITA, 72", VTAC, DVI-D, to DVI-D Male
7-141861141-072
VTAC, Patchcord, ITA, 72", VTAC, DVI-D, to DVI-D Male.
-
product
Signal/Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/ twin female contacts & round posts
510160113
This module comes fully loaded with twin female contacts & round posts (p/n's 610138200 & 610138117).iCon modules mount from the rear of the iCon/i1 receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
product
Pneumatic Contact, ITA, Hose Barb, for 1/8" [3.2 mm] ID Tubing
610131106
Primary mating contact 610131107.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
-
product
Signal, Module Insert, ITA, i2 MX, TriPaddle ,33 Position
510144006
Signal, Module Insert, ITA, i2 MX, TriPaddle ,33 Position.
-
product
Spacer, ITA, G10, .5" Expander for enclosure
276198
Spacer, ITA, G10, .5" Expander for enclosure.0.50" [12.7mm] spacer for G10 ITA- allows wide enclosures to be mounted to G10 ITA frame (p/n 410104123)Adding this spacer between the ITA and Enclosure will allow expansion of the enclosure to greater dimensions than the ITA.
-
product
ITA, I2 Micro ICon, 120/12 Position Hybrid
410130104
The i2 Micro iCon ITA is capable of holding up to 120 QuadraPaddle contacts and up to 12 Micro Power or Micro Coax contacts. Its sleek, 0.8” footprint increases the horizontal stackability. The 30 degree U-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 0.77 in. The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.
-
product
Mini Fiber Optic, Contact, Receiver, Multimode
610113172
* This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113173. (May mate with other ITA contacts, as well.)
-
product
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA
910121178
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA.
-
product
VTAC, Patchcord, ITA or RCV, 36", VTAC, RG178, to Flying Leads
7-145178000-036
VTAC, Patchcord, ITA or RCV, 36", VTAC, RG178, to Flying Leads.All flying leads patchcords must be purchased in quantity multiples of 2. *This patchcord is identical to patchcord p/n 7-146178000-036
-
product
ITA, 9050, 50 Module, Double Tier, for EMI
410104577
ITA, 9050, 50 Module, Double Tier, for EMI
-
product
CAM/TRAC Test Kits
Series 47
The VP Series 47 CAM/TRAC mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 47 provides interface compatibility using the Virginia Panel ITA G12 interface. The ITA frame is offered as an option for those wanting to provide their own ITA Interface.
-
product
Coax, Patchcord, ITA, 36", Micro Coax, RG316 Tan to SMB Plug
7-363116527-036
Coax, Patchcord, ITA, 36", Micro Coax, RG316 Tan to SMB Plug.
-
product
Coax, Patchcord, ITA, 36", Mini Coax, 22 AWG White, Single Ended
7-341922000-036
Coax, Patchcord, ITA, 36", Mini Coax, 22 AWG White, Single Ended.
-
product
ITA, G6x, 9 Module, Removable Backshell, Keying Feature
410104769
The adaptable G6x ITA integrates a wide variety of I/O options in various module configurations that allow engagement of up to 1,920 signal contacts. The G6x ITA has a removable backshell that also reduces electromagnetic interference.
-
product
Tool, Crimp, QuadraPaddle And TriPaddle, Receiver And ITA, Locator Required
910101103
Tool, Crimp, QuadraPaddle and TriPaddle, Receiver and ITA, Locator Required
