Identification
See Also: Identify, ID, Machine Learning
-
Product
Data Analytics
-
KLA’s data analytics systems centralize and analyze the data produced by inspection, metrology and process systems. Using advanced data analysis, modeling and visualization capabilities, our comprehensive suite of data analytics products support applications such as run-time process control, defect excursion identification, wafer and reticle dispositioning, scanner and process corrections, and defect classification. By providing chip and wafer manufacturers with relevant root cause information, our data management and analysis systems accelerate yield learning rates and reduce production risk.
-
Product
High Speed Communication Board
MS 1712
-
- 12 Channel RS422 Standard Communication interface- 4 Channel Configurable Manchester Bi-Phase Signal communications- 4MBPS configurable baud rate- VIRTEX4 FPGA based design- Hardware Frame formation- Hardware Data validation with START & END frame identification and Checksum calculation for RS422 communication- 1MB DPRAM for PCI interface- Separate set of FIFO's for Transmit and Receive channel- 16 Channels data recording through CF (Compact Flash Storage - Capacity up to 8Gbyte) up to 30min @ 2Mb/sec- Online download through USB interface- Driver interface for Windows2000/XP/VISTA and LINUX OS- 6U size cPCI Board- Hot Swap facility is provided for the live Insertion and removing of the board- 12 RS422 channels in front panel interface using two 25-pin D-Type connector
-
Product
FTIR Compact & Portable Systems
-
To meet the challenge of FTIR analysis in the field, Agilent has developed the world's smallest FTIR instruments. Our compact FTIR systems deliver the sensitivity and efficiency of a lab-based system, yet are fully portable. These portable FTIR systems feature integrated power supplies and our Flexscan and Exoscan technology for efficient scanning performance. Lightweight handheld FTIR optics and sampling modules enable advanced FTIR capabilities in field applications such as conservation and mineral identification.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Female, 2m
40-971B-200D-2m-MF
-
This male rear exit to D-type 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
Product
Mobile Gas Leak Detection System
ABB Ability
-
ABB Ability mobile gas leak detection system uses ABB’s patented Off-Axis Integrated Cavity Output Spectroscopy (OA-ICOS) technique which has a sensitivity and precision more than 3000 times greater than legacy methods. This enables identification of leaks several hundred feet away from the source. Current traditional leak detection technology is slow, laborious and costly. Operators walk on foot near the pipeline with hand-held sensors making paper-based reports.This is slow and can lead to dangerous leaks being missed or not identified in a timely manner. ABB’s Ability mobile gas leak detection system delivers a low cost per leak solution with low false positives. Reporting includes mapping of the leaks available via a mobile app and measurements as Cloud-based service. The system consists of ABB’s Methane/Ethane Analyzer, a GPS, a sonic anemometer and proprietary leak detection software that presents real-time geospatial maps of multiple gas concentrations in real time. The software’s sophisticated leak detection algorithm combines the system’s measurements of gas concentrations (CH4, C2H6), local coordinates (GPS) and local wind velocity (sonic anemometer) to estimate the location of the leak. Readings are stored in the device and can be transmitted in real-time to the cloud for centralized monitoring.
-
Product
Ultra High Performance Multi-Sensor Camera System
FLIR M500
-
The gyro-stabilized FLIR M500 cooled thermal camera is our most technologically-advanced M-Series pan and tilt camera ever. Designed around a cryogenically-cooled 640 x 512 pixel Mid Wave Infrared (MWIR) thermal sensor, the FLIR M500 excels at both short and ultra-long range target detection and identification. It features a 14X continuous optical thermal zoom, a color HD camera with 30x zoom, an LED spot-beam, video tracking and radar integration.
-
Product
LC/MS/MS Method Package For Water Quality Analysis
-
Shimadzu provides method files, including pre-registered MRM parameters with optimized quantitative and reference ions, LC separation parameters, and retention times and peak identification parameters for each compound, as well as report templates for outputting quantitation results, as a package. If retention times are adjusted when the system is introduced, based on the HPLC configuration delivered, the analysis process can be started as soon as the specified columns, mobile phases, and standard samples are supplied.
-
Product
Proactive Downstream Spectrum Analysis
SpectraVizion
-
SpectraVizion is an innovative, software-based diagnostics tool that leverages new advancements in remote spectrum capture, allowing cable operators to address downstream spectrum impairments proactively, before subscribers call in with service complaints. “Troubleshooting downstream spectrum issues has always been a reactive process for cable operators,” said Arthur Skinner, Vice President of Worldwide Sales for ZCorum. “Often they’re not aware they have an issue until a customer calls, and that’s when they then send a technician to the home with a hand-held meter to start a search for the problem.” SpectraVizion takes the guesswork out of problem identification and location by presenting on a simple dashboard a list of devices that are experiencing common downstream issues like Standing Waves, FM Noise, Suck-outs, Roll-off and Tilt. The tool leverages the spectrum data available from cable modems and set-top boxes that support full band capture, and advanced detection algorithms automatically identify devices experiencing downstream impairments. The operator can click on any device in the list to view a capture of the full spectrum from that day, or up to 30 days in the past.
-
Product
Vector Network Analyzers
-
The VIA Bravo is a handheld Vector Impedance Analyzer for measuring the impedance and resonant frequencies of circuits and antennas. The VIA Bravo has the capability of providing accurate measurements and sweep displays of impedance, reactance, resistance, phase angle, return loss and SWR. The VIA Bravo’s testing functionality, combined with its 100 kHz to 200 MHz frequency range, make it a versatile tool for many service applications including areas such as MRI, wireless telemetry, 2-way radio, aviation, and Radio Frequency Identification (RFID).
-
-
Product
Field Portable NIR Spectrometers For Mineral Identification And Analysis In Mining Exploration
-
With Spectral Evolution field portable NIR spectrometers and EZ-ID mineral identification software, geologists can measure and identify minerals within seconds and cover more ground than by using traditional methods. They can identify different mineral phases, create mineral alteration maps and more accurately identify mineral pathfinders for vectoring to ore deposits. Spectral Evolution's field portable, battery-operated oreXpress, oreXplorer and oreXpert ultra-high resolution NIR spectrometers are designed for mineral identification in mining exploration. The oreXpress, oreXplorer and oreXpert provide quick payback with faster, more accurate mineral identification in exploration for gold, silver, diamonds, iron, nickel, copper, uranium, aluminum - in the field, core shack, or in the lab, and provide:
-
Product
Spectroscopy Applications
-
Anadis Instruments Benelux b.v.
Spectroscopy has become a powerful tool leading to a broad range of applications, as can be seen in the map below. From the lesser known FT-IR analysis of lipid structures in skin (of interest when applying medicines to the skin as well as in studying the effects of skin aging) to the widely used measurement of additives and the octane number (RON, MON) in fuels. Using spectroscopic techniques has many advantages. The technique is non-destructive; almost any sample can be studied in virtually any state. The techniques are applicable off-line, in-line, at-line or on-line. Identification als well as quantification is possible. Check the map with applications, it will be regularly updated and expanded.
-
Product
Industrial Cameras/ Image Precision
-
Camera-based inspection, identification and process control.
-
Product
Memory Tester
RAMCHECK LX DDR3
-
Quickly test DDR3 DIMM and SO-DIMM memory. In just seconds, RAMCHECK LX will perform a thorough test of the module and provide complete identification. Also tests expensive LRDIMM modules.
-
Product
PDBase II
-
Even very skilled operators will find hard to make a diagnosis, in situations as the one mentioned above, through a mere visual evaluation of the pattern graph . Techimp new technology bases itself on the principle that efficient separation and identification of PD data can be achieved collecting PD pulses themselves and not only, as digital instrumentation commonly available does, PD pulse peak and phase.
-
Product
Cable Fault Locator
TX2001
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
Ground Fault Monitor
IFT-120
-
Our ground fault monitors enable you to easily and quickly find the source of the fault before a major problem occurs and damages your equipment. This is the IFT-120, designed to assist you in rapid identification of ground faults.
-
Product
Passive Probe, 10:1, 500 MHz, 1.5 M
10073D
-
The Keysight 10073D passive probe is our most rugged 500 MHz probe. With a 10:1 attenuation ratio and high 2.2 M ohm input impedance, it is ideal as a general purpose, high bandwidth passive probe for the Keysight 300 MHz - 1 GHz 6000 series, 7000, 8000 and 9000 Series oscilloscopes. The probe identification feature automatically configures the oscilloscope for the probe attenuation.
-
Product
Digital Input Scanner
IM2030
-
Available with us is a digital input scanner that shows the status of digital / potential free inputs connected to the unit. The units are available with 8/16/32 inputs and the names for each input can be configured for easy identification. MODBUS interface is provided to transmit the current status of the inputs to pc.
-
Product
Other Testers
-
Weshine Electric Manufacturing Co., Ltd
It is one of the important planned performance indexes for oil grade and quality identification. In practical application, theselection of suitable viscosity lubricating oil can ensure the normal and reliable operation of mechanical equipment. Thisinstrument is based on the national standard gb265_ The special testing instrument is designed and manufactured for measuring the kinematic viscosity of liquid petroleum products.
-
Product
LXI 24-Channel 1GHz Video Multiplexer
60-721A-001
-
This High Performance Video MUX is designed for the switching of RF signals in 75Ω systems at frequencies up to 1GHz. It is ideal for 75Ω monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment. The automatic connection of unused channels into 75Ω terminations helps maintain signal integrity and minimizes the possibility of introducing unwanted responses. The common connection is also automatically terminated into 75 Ohm when unused. Front panel LED indicators adjacent to each multiplexer input connector provide an easy visual identification of the active channel.
-
Product
Energized Cable Identification System
LCI™
-
The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.
-
Product
Optical Fiber Identifier
-
Anfkom International Co.,Limited
It is an essential installation and maintenance instrument.By inserting the fiber into its adapter head,it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.The 3306A optical fiber identifier also allows relative core power display and identification of the 270Hz,1kHz and 2kHz frequencies. When they are used to detect the frequency, the continuously audible tone is activated.There are four types of adapter heads available: 0.25,0.9,3.0 and 2.0.The 3306A optical fiber identifier is powered by a 9V alkaline battery.
-
Product
Universal LightProbe Connector Cables
ULP-CC
-
Provides fool-proof sensor wiring with color-coded and labeled wires, corresponding to sensor pin labeling, with separate sheathing of individual sensor wires for easy identification at the ATE interface. These will save time and over-all assembly cost, and are long, durable and tested.
-
Product
PXI-5670, 2.7 GHz PXI Vector Signal Generator
PXI-5670 / 778768-01
-
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
Product
Digital Vision Microscopes
-
Sinowon Innovation Metrology Manufacture Ltd.
Video Microscope is widely used in the inspection of electronic industry production line, printed circuit board, weld detects ( such as wrong printing, edge collapse,etc)during printed circuit component, PC Board, VFD, and the identification of printing grid and painting, etc. It can display the zoom out image on the screen and save, magnify and print.
-
Product
Automatic Double Drop Test Machine
DT-JT
-
The machine wills automatic stop positioning after sample reach up to the sated height position. According to the different size to choice the test distance between tests arms, electric pulse width. The release mechanism of machine are flexible and reliable, to ensure the sample without any external influence during the release of instant and free fall way, and make sure it meet sample’s dropping requirements. It is according to GB4757.5-84), GB/T4857.5-92, GB/T2423.5, IEC68-2-27, JISZ0202-87, ISO2248-19, ISO2248-1985(E, ASTMD5276-1998 and ISTA3A. This series drop test bench for measuring the main simulation packages in the transportation, loading and unloading process under drop impact influence, identification package impact strength and packaging design.
-
Product
Optical Microscopy
-
Rocky Mountain Laboratories, Inc.
Optical microscopy from 1X to 1000X is achieved with a variety of microscopes. Images can be formed in bright field, dark field, and differential interference contrast (DIC or ‘Nomarski’) modes. Optical microscopy anlaysis is often used before any other techniques to document samples. Color and morphology are important clues in materials identification.
-
Product
Multispectral PTZ Thermal Camera
FLIR Elara DX-Series
-
The FLIR Elara™ DX-Series multispectral pan/tilt/zoom (PTZ) security camera provides full situational awareness in the most punishing environments. Combining thermal and visible light imagers, the Elara DX-Series gives operators the ability to monitor large areas in complete darkness, glaring light, and adverse weather. The exceptional detection and identification capabilities of multispectral cameras help integrators provide solutions for challenging imaging problems at critical infrastructure sites and remote facilities.
-
Product
Ring Disk Electrode
-
This ring-disk type electrode developed by NTT Advanced Technology Corporation is a form of printed electrodes. Users can choose them from Carbon, Gold and Platinum applied versions. Available as a working electrode of radial flow cells, achieves complete reduction/oxidation on the center disk at ultra-low flow rate because of its fine coulometric electrolysis efficiency. This also enables to analyze subsequent reaction as well as identification and quantitation of the sample at the same time.
