Filter Results By:
Products
Applications
Manufacturers
Stepper Motors
A device that translates electrical pulses into precise mechanical movement. The output shaft may deliver rotary or linear motion. (www.seanet.com)
-
product
Stepper Motors
Stepper motors provide precise motion without the need for position feedback or commutation. Our stepper motors are available in unipolar or bipolar configuration and 1º to 90º step angles.
-
product
Stepper Motors
We carry a wide variety of stepper motors including washdown stepper motors for use in wet or dusty environments, 2-phase bipolar motors, integrated stepper motors, and more.
-
product
Closed-Loop Linear Actuators w/ Stepper Motors, Encoders, and Controllers
A-BAR-E Series
Zaber's A-BAR-E Series products are computer controlled, motorized, ball screw driven linear actuators (electric cylinders) with integrated feedback encoders. They are stand-alone units requiring only a standard 48 V power supply. A built-in encoder allows closed-loop operation and slip/stall recovery features. A manual knob at the end of the unit permits manual control - press and hold to switch between velocity mode and distance mode, turn to move the actuator, and press to stop.
-
product
Hybrid Stepper Motors
Hybrid stepper motors from IMS are available in rotary sizes NEMA 11 (28 mm) through 34 (85 mm), and linear actuator sizes NEMA 17 (42 mm) and 23 (57 mm). These extremely robust, long-life motors carry out precise step-by-step movements that are controlled by a stepper motor drive, such as MForce, to comprise a stepper motor drive system.
-
product
Mezzanine System
5093
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
product
Motor Driver ICs
The ST product portfolio offers a wide range of motor control ICs, well-suited for the most demanding automotive environments, covering the requirements of brushed DC motors, stepper motors and brushless DC motors, over an extensive range of voltage and current ratings. Efficiency and accuracy of our motor drivers are guaranteed by a unique combination of low-loss PowerMOS output stages and advanced control circuitry. Robustness and reliability are provided by the integration of a comprehensive set of protection and diagnostic features.
-
product
Motors
Pittman and Haydon Kerk motor lines span a wide range of sizes in brushed, brushless and stepper motor technologies. We provide rapid turn-around for prototypes and production orders. Custom designs and special engineering requirements such as special shaft diameters, lengths and mounting flanges are welcome.
-
product
Stepper Motor ,High-Precision Linear Stages,Application for Industry
KSAXXX-13-X
Model: KSAXXX-13-X Stepper Motor ,High-Precision Linear Stages,Application for Industry
-
product
Optical Delay
ODL
The Peregrine Optical Delay Line (ODL) provides an exceptional combination of precision, speed, and optical stability at a low price. It is ideally suited for pump-probe experiments and autocorrelation measurements (both interferometric and intensity methods). Advanced voice coil technology allows the ODL to be positioned anywhere in its travel range to within 150 nm. That’s 1 fs for a double-pass configuration. The response time is as short as 1 ms. Our 1-cm-travel ODL is interferometrically stable (measured using a 650 nm laser). No backlash, no hysteresis and no drive trains to wear out as with stepper motors. It’s convenient–the ODL can be positioned using digital commands, an analog voltage or a combination of the two. Two 16-bit on-board analog-to-digital converters simplify data collection. Digital inputs and outputs allow master or slave clocking. An executable Windows application is provided to get you up and running in minutes. In addition, DLLs and LabVIEW Vis for integration into your software are also included.
-
product
Custom Automation Equipment And Assembly Machinery
Automated test equipment, precision positioning robots, stepper motor, and servo motor mechanisms in support of testing and repetitive manufacturing from TetraTek Products, Inc.
-
product
Econo Motion Controllers
DMC-41x3
The DMC-41x3 motion controller is one of Galil's latest generation, stand-alone motion controller. Compared with the DMC-21x3 controller, the DMC-41x3 offers the following enhancements: 100BASE-T Ethernet, aux RS232 port, USB port, uncommitted analog inputs, up to 15 MHz encoder frequencies, more program memory, and faster sample frequencies. The DMC-41x3 also accommodates the same stepper and servo motor drives used in the DMC-40x0 series and allows two 4-axis 750 W drives to be installed in the 8-axis controller package. The DMC-41x3 is available as a box-level or card-level motion controller. The unit operates stand-alone or interfaces to a PC with Ethernet 10/100BASE-T, or USB. It includes optically isolated I/O in addition to analog inputs and outputs. The DMC-41x3 controller and drive unit accepts power from a single 20-80 VDC source.
-
product
Closed-Loop Motorized Linear Actuators with Built-in Encoders
LAR-E Series
Zaber's LAR-E Series products are computer controlled, precision lead screw driven, motorized linear actuators (electric cylinders) with integrated feedback encoders. A built-in encoder allows closed-loop operation and slip/stall recovery features. Each electric cylinder is wired for use with Zaber's A-Series stepper motor controllers, or they can be used with any 2-phase stepper motor controller through the panel mount DB15 connector. When connected to our A-Series controllers, the actuators are designed to be "plug and play" just like all of Zaber's other products.
-
product
Stepper Motor Controller for CompactPCI
CPCI322
The CPCI322 is a 3U CompactPCI card. The CPCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
product
Triaxial Testing Machines
Triaxial testing machine for position-controlled triaxial tests with test cells 10-3150 ... Stand model in two-column design with electronic force transducer, flanged to the testing machine crosshead and adjustable electronic position transducer 50 mm. The machine is driven by a stepper motor with central spindle and pressure plate below.
-
product
Programmable/Direct Reading Attenuators
Is a dual function direct reading and programmable rotary vane type attenuator for use in millimeterwave systems across the standard WR-03 frequency range of 220 to 330 GHz. The attenuator is an ideal piece of equipment in waveguide systems where a broad direct reading of attenuation is required. The default mode of operation is manual direct reading. In manual mode, the attenuation is adjustable with the large knob and the digital LCD screen displays the current attenuation value. The LCD screen is powered by an internal rechargable battery, which is charged via the 2.5mm DC jack by a provided DC to AC adapter. The 2.5mm DC jack also provides power to the stepper motor, encoder and internal microprocessor for the programmable mode function. The user can quickly switch to programmable mode by connecting the powered-up attenuator to a computer with the USB Type B port. In programmable mode, the attenuation is finely adjusted with a precision stepper motor by the internal microprocessor via user-entered serial port commands from the computer.
-
product
Hematology Analyzer
ABX Micros 60
Process efficiency in Hematology- Impedance technology, photometry- Microsampling: Only 10 µL- Smart card based memory storage (optional)- No compressor (stepper motor technology)
-
product
Stepper Motor Controller for PCI
PCI321
The PCI321 Intelligent Stepper Motor Controller with amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.
-
product
Centralized Motion Controller
ADLINK‘s pulse train controllers provide comprehensive and application-oriented motion functions for servo and stepper motors through digital signal processing (DSP)-based and Application Specific Integrated Circuit (ASIC)-based two pulse train mode controllers to achieve excellent synchronous motion control and precise positioning suitable for laser engraving, marking and cutting applications in semiconductor, AOI, and conventional manufacturing industries.
-
product
Big Easy Driver
The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next version of the popular Easy Driver board.
-
product
Actuators, Adjusters, & Transducers
We offer a wide range of adjustment screws, micrometers, and kinematic positioners, as well as stepper motor, DC servo, high-precision piezo inertia actuators, and voice coil actuators. Additionally, our piezoelectric offerings include modular, screw, and replaceable-tip piezoelectric actuators, as well as Langevin transducers for ultrasonic welding applications. A wide variety of piezoelectric chips and stacks are also available.
-
product
Stepper Motor Controller for PCI
PCI322
The PCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications
-
product
Stepper Motor,Ultra-Thin Linear Stage
TSAXXX-C
Model:TSAXXX-C Stepper Motor,Ultra-Thin Linear Stage Rotation with super grinding ,slide with v-shapped rail ,elastic couplings have adopted import high-quality products,supply quality assurance .The design of the limited switches and zero switch and standard interface are converient for output of sigal ;Equipped with handwheel in the back of motor ,achieve manual adjustment;Standard hole is convenient for combined-dimensional . The height is 30mm,the largest height is only 44mm.Application for little height of space,little travel,high resolution fields.
-
product
Stepper Motor Controller for VMEbus
VME321
The VME321 Intelligent Stepper Motor Controller with Amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.This VMEbus board has a 6U form and is also available as 3U VMEbus board.
-
product
RL78 Family Of 8/16-bit Ultra-Low Energy MCUs
RL78/D1x (Automotive Only)
Renesas is introducing the RL78/D1x as an optimized solution for the BRICs and low-end instrument cluster markets. The RL78/D1x is the successor of 78K0/Dx2 or UPD78082x microcontrollers and suited for car instrument cluster, built-in car instrument cluster dedicated features such as Sound Generator, Stepper Motor Controller/Driver and LCD Segment Controller/Driver etc.
-
product
Engine Control
StepGenerator4
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
product
Stepper Motor,Linear Stage,Large Load
TSAXXX-B(F)
Model:TSAXXX-B(F) Stepper Motor,Linear Stage,Large Load Standard products has adopted ball screw,precision products has adopted grinding screw ;Slide has adopted linear bearing;Elastic couplings adopts high-quality imported products ,ensure the machine quality .The design of limited swtiches and zero switch,standard interface are convenient for signal’s output. The handwheel in the back of motors,can achieve manual adjustment. Standard hole is convenient for combined-dimensional ;Additionally , can reload servo- motor ,assemble grating,install un-dust cover ;Application for high load and high-stability fileds ,extensively used in industry.
-
product
Stepper Motor Controller for VMEbus
VME322
The VME322 Intelligent Stepper Motor Controller is designed to drive up to eight external Amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. Local processors handles all high-level commands to provide maximum control for both straightforward as very complex applications.
-
product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
product
Electromechanical Testing Machines
Stand model in four-pillar design with electronic force transducer, flanged to the movable testing machine crosshead and electronic position transducer for measuring the crosshead path. The machine is driven by a quartz-precise stepper motor with two ball screws. Complete with integrated displacement measuring device 0.01 mm over the entire travel distance as well as additional displacement transducer with connecting cable and holder
-
product
Exhaust Pressure Controller
EC-5000 Series
The EC-5000 series exhaust pressure controller can maintain a consistent pressure, of the user’s choice, within the chamber. The high-resolution stepper motor and unique butterfly valve ensure a fast, sensitive response to any pressure changes.
