PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
product
Adapters & Pin Converters
Need to adapt your emulator's JTAG connection? We have a variety of pin converters to help connect your debug probe to your target board's JTAG connection, such as TI, MIPI, ARM, and Cortex.
-
-
product
1.85mm Adapters
Pasternack 1.85mm adapter category majority are RoHS and REACH compliant. 1.85mm adapter components are part of a comprehensive adapter product line from Pasternack.Our 1.85mm adapters allow you to interface 1.85mm connectors with 1.85mm, 2.4mm, 2.92mm, 3.5mm, N, SMA or SSMA connectors. 1.85mm adapters are constructed in female to female, female to male, male to female or male to male gender designs.Pasternack's ISO 9001:2008 registered facility ships 1.85mm adapter series the same day from the broadest and deepest in stock inventory of microwave and RF parts. Excellent technical support and customer service are on hand to assist you.
-
product
PXI Module Adapter, Pull Thru Adapter, Receiver, 1 Position
510109462
PXI Module Adapter, Pull Thru Adapter, Receiver, 1 Position.
-
product
MTB Calibration Adapter
2450-CAL-30
The MTB Calibration Adapter (Catalog No. 2450-CAL-30)is a socket adapter that’s designed to bring phase A, B, and C current and potentials of a TESCO Multi-Position Test Board to an external RD-30 reference standard for calibration of the Test Board.
-
-
-
product
FMC, XMC & PMC
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
-
product
PMC Carrier for PCI Card Interface
TPCI270
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
product
PCI Express x1 PMC Carrier
TPCE261
The TPCE261 is a standard height PCI Express Revision 2.0 compatible module that provides one slot for a single-width PMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control. The TPCE261 is a versatile solution to upgrade well known PMC I/O solutions to the PCI Express signaling standard.
-
-
product
Adapter Plates
ARINC 791 compliant adapter plates simplify and standardize antenna and radome installations by providing commonality and interchangeability across entire fleets.
-
-
-
product
160-Position QFP-to-PGA Adapter
96-160M65
QFP to PGA Adapter for 160 Position, .0256 [.65] Pitch. Convert surface mount QFP packages to a 15 x 15 PGA footprint. Reduce costs by using less expensive QFP packages to replace PGA footprints in existing designs. Pins are mechanically fastened and soldered to board using Aries patented process, creating a reliable electrical connection and rugged contact.
-
product
PMC Carrier for 3U CompactPCI
TCP270
The TCP270 is a standard 3U CompactPCI carrier that provides front I/O and rear I/O for a single width PMC module. This PMC to 3U CompactPCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in CompactPCI systems.
-
product
PCIe Adapter for XMC
PCIe4LXMCX1
Simple and easy to use. Install PCIe4LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position. XMC´s with up to 8 lanes can be used. The PCIe lanes to/from the XMC are routed per PCIe specifications with matched lengths and impedance control.
-
product
USB CAN Interface Adapter
COMMDongle
Designed for use with VISUALCONNX and other third-party software, COMMDongle products initially support one or more CAN communications buses.
-
product
100-FX Fiber Optic Ethernet PMC
3006
The Ethernet 100-FX Adapter provides a single port Ethernet connection using Fiber Optic media. An AMD 79C973 Ethernet controller provides a integrated link and physical layer for operating at 100 Mb/s. The Fiber Optic connector used on the board can be either the ?SC Duplex? style, or the ?ST RX/TX? style and is identified by the Technobox Part Number.
-
-
product
PCI Adapter for cPCI
PCI2cPCI-32
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
PCI to PMC Adapter/Carrier
PCI2PMC
The PCI2PMC ( PCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI slot. The PCI2PMC has a PMC card slot mounted to a universal 1/2 length PCI card. Suitable for 32 bit or 64 bit data with 33 or 66 MHz bus operation. The PMC user IO connector Pn4 is brought out to two connectors for access (DIN IDC and SCSI II compatible).
-
product
Expansion Adapter Chassis
TB3-TO-CMC-LP
The TB3-TO-CMC-LP is an expansion adapter chassis using the Intel Thunderbolt 3 interface. The adapter allows the use of a front I/O XMC or PMC card outside its normal confines of a single board computer (SBC) or PC hosted carrier card. The TB3-TO-CMC-LP enables the deployment of XMC or PMC modules in systems previously unable to host them -- laptops, small form factor PCs, and other computers lacking add-in slots.
-
product
GPIB Bulkhead Adapter, Female/Female
182766-01
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Female GPIB (IEEE 488) Bulkhead - The GPIB Bulkhead connects GPIB cables to other accessories. NI offers it in Type XC and XD.
-
product
PCIe Carrier For PMC And PrPMC
PCI104
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
product
Test Adapter / Extender
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
product
XMC-to-PCI Express Adapter
7988
The Technobox, Inc. P/N 7988 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 7988 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
product
Vacuum Test Adapter
Vacuum test adapters (VA) are suitable for contacting electronic assemblies with large quantities (mass testing) and a small number of variants. INGUN vacuum test adapters are available as standard as a single system without an exchangeable replacement kit.
-
product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-01
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
