-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
160 Pin Female DIN to QuadraPaddle Flying Lead Cable, 48", 024070
VFL103124-048
Flying Lead Cable
Vendor Flying Lead (VFL) Cable, 160 Pin Female DIN to QuadraPaddle Leads, 24AWG Twisted Pair, 80 T/P's(1:2) 160 connection points, M2.5 x .45 fastener, CONN: 024070 WIRE: VPC, for PXI-2737, PXIe-2738 families, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 20" length.
-
Product
Additional Products: 500 Pin SEARAY Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Ferrules, 2m HV, Exit Towards Pin 1
A050DF5-F-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Additional Products: 44 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, to 68 Pin SCSI Female
510140251
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, to 68 Pin SCSI Female
-
Product
1 Meter Long SCSI Cable with 100 Pin Connector
U2903A
Digital Cable
The Keysight U2903A is an accessory compatible and recommended to be used with the U2600A Series USB used with the U2600A USB Modular Digital I/O modules. The pin-outs of the U2903A is dependent on the USB Modular Digital I/O module that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2903A is to be used with.
-
Product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Tinned Ends, 1m
A025CFR-T-5A100
Cable Assembly
This 1m long female 25-Pin Micro-D to unterminated (with tinned ends) cable assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product.
-
Product
Solid Pins
-
Advanced Probing Systems, Inc.
APS produces electro-chemically machined pins in diameters between .020"-.040" in a variety of materials for use in various applications. These “large diameter pins” are used in various medical applications, industrial applications, board testing, LED & LCD test and as components in small tools. APS’s design services can help you select the optimal material from tungsten, beryllium-copper, Paliney 7® or various stainless steel alloys or work with the material of your choice. Pins can be produced with either a sharp or radius (rounded) tip. Tapers can be highly polished, slightly polished, matte or neutral in finish.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 2m HV, Exit Away From Pin 1
40-970-050-2m-MF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 24 AWG Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
04 With Pins For PCB | 3 Wafers | 12 Positions
04-3xx4-20/70-xx
-
Very robust, multi wafer selector with 30° detent angle, switching torque up to 20 Ncm and a rotational life up to 25'000 cycles
-
Product
100 Pin 1.27mm Pitch Micro-D Connector & Cable Accessories
-
The 100 Pin 1.27mm Pitch Micro-D connector is used on many products to provide a high density 1A connector solution that is suitable for use to 150Vdc If you would like to develop your own cabling solutions, we offer mating connectors and connector hoods that allow you to create either your own cable based solutions, or a PCB header solution. Connector Blocks directly terminate the module connector and convert the connection to arrays of screw terminal blocks, or you can select to use a remote DIN rail mounted breakout to terminate the cables at the end of a cable assembly. You can also try our Cable Design Tool to graphically design a customized cable assembly.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 2m HV, Exit Towards Pin 1
A050DM5-F-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
37-Pin D-Type Male Solder Pin HV
92-960-037-MHV
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
200 Pin D Cables - 200 Pin to Alternative Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 200-pin D connector.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 2m HV, Exit Towards Pin 1
A050DF5-C-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, Receiver, 20", QuadraPaddle, 160 Pin Female DIN
540069010129
Cable Assembly
Cable Assembly, Receiver, 20", QuadraPaddle, 160 Pin Female DIN.
-
Product
Additional Products: 104 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
160 Pin Female LFH to QuadraPaddle Flying Lead Cable, 36", 780009-02
VFL159124-036
Flying Lead Cable
Vendor Flying Lead (VFL) Cable, 160 Pin Female LFH to QuadraPaddle Leads, 28AWG Twisted Pair, 160 T/P's, SHARED GROUNDS 80 T/Ps, 168 connection points, CONN: 780009-02, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 36" length.
-
Product
Cable Assembly, Receiver, 36", TriPaddle/Mini Power, 4 Banana Plugs, 7 Pin DIN
540198010211
Cable Assembly
Cable Assembly, Receiver, 36", TriPaddle/Mini Power, 4 Banana Plugs, 7 Pin DIN.
-
Product
Cable Assembly, Receiver, 20", TriPaddle, to 25 Pin Female D-Sub
540014010101
Cable Assembly
Cable Assembly, Receiver, 20", TriPaddle, to 25 Pin Female D-Sub
-
Product
Load Pins
-
When overload protection and/or load indication is to be installed in a conveyor, crane or other device, the PIAB SLC is the ideal solution. The PIAB SLC Load Pin easily replaces the existing shaft at an equalizing pulley or in other parts of the construction. The PIAB SLC Load Pin should be installed as close as possible to the force/load for best accuracy. Both the PIAB SLC Load Pin and the PIAB LCA Amplifier are designed to withstand extreme environmental conditions for a long operation time.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 68 Pin Male VHDCI
540120010240
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 36", 68 Pin Male VHDCI
-
Product
Pin Insertion Tool For Scorpion Connectors With Crimp Pins
C020AFR-2CP-2A-I
Insert Tool
Extractor tool for crimp pins fitted into a Scorpion connector housing.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 200 Pin Male LFH, M3 jackscrews
540105040105
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 200-Pin Male LFH, M3 jackscrews
-
Product
500 Pin SEARAY Connectors For Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a 500-pin SEARAY (250-port) connector.
-
Product
2.5mm Test Wire Test Probe Pin
CX-3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test wire test probe pin 1.Application: Used to verify the protection of persons against access to hazardous parts. Also used to verify the protection against access with a tool.
-
Product
25 Pin D-Type Connector Blocks For Pickering Products
-
The connector blocks below are suitable to use with Pickering cards and modules that utilize a 25-pin D-type connector.
-
Product
Cable Assembly, Receiver, 20", TriPaddle, 50 Pin FML D-Sub
540111020103
Cable Assembly
Cable Assembly, Receiver, 20", TriPaddle, 50 Pin FML D-Sub.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 1m HV, Exit Away From Pin 1
40-970-050-1m-MF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
