Genrad Fixtures
An I/O test interface platform, created by Pylon adopted and extended by Genrad (now Teradyne).
See Also: Board Test Fixtures
-
Product
Main Air Data Test Fixture for ADC's
TA-245
-
This is the Main Air Data Test Fixture as shown in the AZ-241 repair manuals and will allow by the book testing of the units.
-
Product
ICT Test Fixture
-
It can be produced in our overseas branches which are Thailand ,China and India.High precision test fixture can be produced.Test fixture for other brand testers can be produced.
-
Product
VOC FIXTURE OVER CLAMP ASSEMBLY'S
-
Test-X VOC Series overclamps are used for testing bare or loaded printed circuit boards with open vias and to minimize board flex.The VOC Series overclamp comes with adjustable delrin pressure fingers, anti-rotating hex nuts, hinge and latching assemblies, mounting instructions and hardware.The VOC Series will accomodate fixtures with dress frames or newer style fixtures using full-size top plates.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,30 kg
-
Product
Open Source Hardware Test/Programming Fixture
OpenFixture
-
OpenFixture is a fully parametric programming/test fixturing solution written in openscad. The inputs are generated/captured from the users board layout software and a laser cuttable fixture is generated automagically.
-
Product
Lamp & Fixture Wiring Tester
GT3110GAM LAMPCHEK
-
LampChek indicates the lamp and fixture continuity.
-
Product
In-Circuit Test Fixtures
-
Every type of in-circuit test fixtures (wired, wireless, pneumatic, vacuum) for all major tester brands.
-
Product
Turn-Key Functional / Mechanical Fixture
-
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
Product
HiFIX High Fidelity Tester Access Fixture
-
The HiFIX lineup delivers clean waveform transmission, precision docking, and multi-DUT parallel test, with high reliability.
-
Product
Automatic Fixture Removal
S96007B
-
Automatic fixture removal (AFR), is the easiest way to remove fixture effects from non-coaxial device measurements.
-
Product
Clamshell Type Mechanical Fixtures
Series 10
-
Semco MT Series 10: An affordable solution for testing of printed circuit boards.
-
-
Product
Ethernet Test Fixtures & Software
-
We have developed a series of custom testing tools as part of our dedication to performing the most comprehensive Ethernet testing in the industry. These tools allow for testing at lower layers than most commercially available tools and are available for use in your own testing labs. In addition, we have an extensive amount of T&M partner test tools which members of our Ethernet testing services also have access to.
-
Product
Absolute Length Gauges For Measuring Stations And Multi-gauging Fixtures
ACANTO series
-
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
-
Product
Manual Fixture Kit
230354 – CMK-05
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Universal Test Fixture
Series 48
-
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
Product
Manual Test Press Fixture
750/752 Series
-
RTI's manual test presses are compact, portable, all-inclusive, and easy to use. Single lever operation and 100% vertical compression makes the manual test press an ideal solution for PCB, hybrid module, and high pin count device-level testing when complex test requirements cannot be met with a test socket and breakout board alone.
-
Product
Custom Fixtures
-
Joule mechanical design and manufacture capabilities allows us to create other custom projects to meet your test needs. Joule can design burn-in racks, jigs and stand-alone test station.
-
Product
In-Circuit Fixtures
-
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
Product
Burn-In Test Fixtures
-
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
Product
ICT/FCT-Fixtures, Max UUT 250 × 180 mm (wxd)
CK-1-228X-S (Small IF) / 230514
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Bending Stiffness Test Fixture
-
Q-Card’s bending stiffness fixture features splayed feet and aggressive no-slip rubber pads for stability. It is manufactured of aerospace-grade aluminum alloy with a hard anodized, scratch-resistant, durable finish to provide years of rigorous testing and trouble-free service.
-
Product
ICT/FCT-Fixtures, Max UUT 250 × 180 mm (wxd)
CK-1 Small (Hold-Down Gate) / 230154
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5/HG
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 10,70 kg
-
Product
Tool, Adapter, Holding Fixture Adapter AT-1319-29
910121149
Adapter Tool
Used with Raychem holding fixture to aid in the solder process for Mini-Coax Solder sleeve contacts. Both fixture and adapter are included in Solder Kit Part # 910121144.
-
Product
Custom Fixtures
-
The shock and vibration fixture model BW-SV-3X3X3 is designed to accept up to 24 each of the TO-3 packages on each of the 6 axes and mount to the vibration shaker model BW-100C and Shock Tester model BW-E5000. The fixture is made of white derlin and measures 3”x3”x3”and weighs approximately 13 ounces. The fixture includes a white derlin cube with a 2 ¼” bolt circle and 4 10-32 x 3” cap screws.
-
Product
Custom Vibration Testing Fixtures
-
Paragon Systems is unique in being able to not only perform your vibration test, but also to design, fabricate and qualify your vibration testing fixtures. Usually all we need from a client is their vibration test profile, a CAD model and the GD&T of the DUT.
-
Product
Press - Down Fixture Kits
-
*Supports most press - down testers *High - Quality *Precise & Reliabe
-
Product
Test Fixtures & Jigs
-
A test fixture or test jig is the component containing the bed of nails used for testing the PCB or assembled product. It is powered and controlled by the Yelo Testpoint system which has test cards capable of providing multiple test conditions. This system also controls the probes used in the bed of nails, and relays test information back to the Testpoint system to be analysed.
-
