Filter Results By:
Products
Applications
Manufacturers
Genrad Fixtures
An I/O test interface platform, created by Pylon adopted and extended by Genrad (now Teradyne).
See Also: Board Test Fixtures
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Test fixtures
Offers a wide range of standard Test Fixtures that can fit many of your applications and services. From your R & D to your production lines, we have a solution for you.Each products are standard but we can adapt or design your application.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
Fixture Design
TestEdge offers quick, cost effective test fixture design services for low-speed, full-speed, and high-speed devices. Based on our experience in developing high performance test fixtures for a wide variety of devices, test sockets, and tester platforms, we provide a premium quality test and engineering validation environment for everything from high power (40W) to high pin count to high speed ECL to high speed SerDes (3.25Gb) devices.
-
product
Vacuum Fixture Kits
*Perfect Sealing *Precise Operation *Stable Construction *Self Closing - Opening Covers
-
-
-
-
product
Customized Test Fixtures
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
-
product
Magnetizing Fixtures
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
product
Exchangeable Test Fixture
MA 2109/D/H/S-5
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg
-
product
Liquid Test Fixture
16452A
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
-
product
Cable-End Test Fixtures
Test Head Engineering's cable-end fixtures are used in the production of cable harnesses and in the testing of finished products. They are the long-lasting "connector" to the test system - taking the place of connectors that would quickly exceed their cycle life and produce erratic test results. Cable-end fixtures are used in the automotive and heavy equipment industries, but are also applicable wherever low cycle-life connectors are used - including RF cables.
-
product
Functional Test Fixtures
Businesses rely on Circuit Check’s functional test fixture expertise. Functional test typically applies full operational power to a loaded printed circuit board in order to determine if the PCBA performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies.
-
product
Board Test Fixture Probes
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
product
ICT/FCT-Fixtures (Small IF)
GenRad CK-2-228X
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
product
Function Test Fixtures
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
product
Manual Fixture Kit
230355 – CMK-06
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Test Fixture Kits
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
product
Multi-Stage In-Circuit Test Fixtures
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
product
Vacuum Test Fixtures
Series 63
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
