Analog Input
measurable voltage value.received from a sensor.
-
Product
64-Channel 250kSa/s USB Modular Multifunction Data Acquisition
U2355A
Data Acquisition Module
The U2355A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2351A to simulate simultaneous analog input acquisition.
-
Product
Multi-Function DAQ
-
Full spectrum of DAQ cards provides analog input and output, digital input and output, and counter/timer circuitry.
-
Product
SH68M-68M-EPM, Male 68 pin SCSI to 68 pin VHDCI, 0.3m
192288-0R3
Multifunction Cable
68-Pin Male VHDCI to 68-Pin Male VHDCI, Twisted Pair, Shielded Multifunction Cable - The SH68M-68M-EPM Cable, sometimes referred to as SHC68-C68-EPM, connects DAQ devices. The cable includes separate digital and analog sections, individually shielded twisted pairs for analog inputs, individually shielded analog outputs, and twisted pairs for critical digital I/O. The SH68M-68M-EPM Cable is offered in different lengths.
-
Product
Analog I/O module with 32/16 multiplexed analog input channels
IO102
-
Fast 16-bit analog module with 32/16 multiplexed analog input channels and 4 analog output channels. This I/O module offers lower input sampling and conversion times than the IO101 and therefore leads to smaller overall driver latency time. It is similarly priced as the IO101 but comes with 4 analog outputs instead of 8.
-
Product
Dataloggers
CR300-Series
-
CR300 dataloggers are small, low-cost, high-value dataloggers with many of the features of other Campbell Scientific dataloggers. In addition, the CR300 dataloggers offer faster communications, low power requirements, built-in USB, and excellent analog input accuracy and resolution.
-
Product
PCI-6111, 2 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777530-01
Multifunction I/O
2 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6111 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6111 is ideal for a variety of applications, such as … stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6111 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
PXIe-7862, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
786672-01
Multifunction Reconfigurable I/O
PXIe, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7862 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 16 analog input channels connected directly to a Kintex-7 325T FPGA, you have ample space to design applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7862 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7862 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
PC/104 SBC with Vortex86DX3 1GHz CPU and Data Acquisition
HELIX
-
The HELIX family of PC/104 SBCs combines mid-range CPU performance, standard PC I/O, and on-board data acquisition circuitry in a compact size and at a competitive price. Available PC I/O includes 3 or 6 USB 2.0 (model dependent), 4 serial ports (2 RS-232/422/485 and 2 RS-232), 1 10/100Mbps Ethernet, 1 Gigabit Ethernet, and a SATA port. The optional data acquisition circuit includes 16 16-bit analog inputs, 4 16-bit analog outputs and 27 digital I/O lines configurable as counter/timers and pulse width modulators.
-
Product
Sensor Processing
-
If you need analog input boards for video compression, SDR, SIGINT, radar, sonar, imaging or T&M - we can help.
-
Product
NI-9252, ±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module
786783-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module - The NI-9252 is an 8-channel analog input module for CompactDAQ and CompactRIO systems. Each channel provides a ±10 V measurement range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9252 features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
Direct BNC
0001045
-
Interface board plugs directly into National Instruments 68 pin multifunction and simultaneous sampling DAQ cards (PCI and PXI). First four analog inputs, two analog outputs, and trigger channels are available on BNC connectors (SMA/SMB optional).
-
Product
16-bit, 200KHz, 16 Isolated Differential Analog Input Board, 8 Isolated 24V Digital I/O
APCI-3002
-
Analog input board, 16-bit resolution, 16 differential inputs with 200 kHz sampling rate.
-
Product
Closed-Loop Motor Controller
MS320
-
Master and Ratio-Follower modes and programmable input functions. Options include analog speed feedback input, analog setpoint inputs and relay outputs. Works with incremental shaft encoders and pulsefrequency output shaft speed sensors. Optional explosion proof enclosure or NEMA 4X enclosure kit.
-
Product
Analog Input Modules
-
The modules provide direct connection to a wide variety of sensors and annunciators. They perform all signal conditioning and linearization and contain no pots or DIP switches. All user-selectable settings, such as ranges are stored in nonvolatile EEPROM, which maintains these values even after power is removed.
-
Product
4-CH 16-Bit 10/40 MS/s PCI Digitizers with 512 MB Memory
PCI-9816/9846
Digitizer
The ADLINK PCI-9816/9846 are 10MS/s, 40MS/s sampling 16-bit 4-CH digitizers designed for digitizing high frequency and wide dynamic range signals with an input frequency up to 20 MHz. The analog input range can be programmed via software to ±1 V or ±0.2 V and ±5 V or ±1 V. With a deep onboard acquisition memory up to 512 MB, the PCI-9816/PCI-9846 are not limited by the data transfer rate of the PCI bus to enable the recording of waveforms for extended periods of time.
-
Product
16-Channel 500kSa/s USB Modular Multifunction Data Acquisition
U2354A
Data Acquisition Module
The U2354A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2354A to simulate simultaneous analog input acquisition.
-
Product
16-Channel VME RTD/Resistance Input Module
V410
-
The V410 is a 6U VME module that provides sixteen independent analog inputs that may be used to read RTDs, thermistors, and other similar resistive sensors. It can also read cryogenic diodes. Users may set input range and adjust other settings at VMEbus speed, and depending on the range selected the microprocessor will do the necessary calculations and output voltage, resistance, or temperature. Temperature conversion is available for 100Ω and 1000Ω, series 385 and 392, platinum RTDs.
-
Product
PMC w/ 16x/8x ADC, 8x/4x DAC & 14x Digital I/O
TPMC532
-
The TPMC532 provides 16 or 8 channels of simultaneous sampling true differential bipolar 16-bit analog input, 8 or 4 channels of simultaneous update single-ended unipolar/bipolar 16-bit analog output and 14 channels of tri-state 5V-tolerant TTL digital input/output.
-
Product
16-Bit Multi-Function With A/D, D/A And Digital I/O Channels CPCI Cards
GX3232 Series
cPCI Card
The GX3232 is a multi-channel 16-bit, analog input and output cPCI module, supporting 32 single-ended or 16 differential input channels and four analog output channels. The inputs can be software configured for differential or single-end operation and are sequentially scanned with a maximum aggregate scan rate of 300 kS/s. Three input ranges are software-selectable: ±10 V, ±5 V or ±2.5 V. Optionally, the GX3232 is available with a high voltage input configuration and supports three ranges: ±60 V, ±30 V and ±15 V. The high voltage configuration supports 16 single-ended or 8 differential input channels for high voltage and 16 single-ended or 8 differential inputs for low voltage measurement. Four analog output channels provide software-selectable output ranges of ±2.5 V, ±5 V or ±10 V. The outputs can be updated either synchronously or asynchronously and support waveform generation. Each output can be clocked at rates up to 300 kS/s. A 16-bit digital I/O port is also provided, which supports 16 bidirectional data lines. Note that when used with a TS-700 system only 8 of these digital I/O lines are available at the test system's receiver interface.
-
Product
NI-9238, ±500 mV, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783311-01
Voltage Input Module
±500 mV, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9238 performs differential analog input. The measurement range is compatible with many low-voltage sensors such as current shunts and current transducers in high-current applications. When used with higher-voltage C Series Voltage Input Modules, the NI‑9238 can measure power and energy consumption for applications such as appliance test, industrial machine monitoring, power quality analysis, phasor measurements, and harmonic analysis.
-
Product
PCIe-Mini
PCIe-Mini-AD8200
-
8 Channels 16-bit A/D converter Simultaneously Sampled• Fast throughput rate: 200 KSPS for all 8 channels• 8 Channels SE or 4 PSEUDO Differentials• Single-ended or 4 differential channels• True bipolar analog input ranges: ±10 V, ±5 V, selection applies to all Channels• Analog Input Clamp Protection• 1MΩ Analog Input Impedance• Programmable 2nd Order Anti-alias Analog Filter• Over-sampling capability with digital filter• 8Kx16 SRAM• PCIexpress compliant
-
Product
32-CH Isolated DIO PCI Cards
PCI-7230/33/34
Analog Input Module
ADLINK"s PCI-723X series are 32-CH isolated input and/or output cards which provide a 2,500 V optical isolation protection. The wide input range of the PCI-7230 and PCI-7233 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The PCI-7230 and PCI-7234 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automation applications. The PCI-7234P provides current-source output capability. The PCI-7230 and PCI-7233 also provide two interrupt sources on digital input channels. The PCI-7233 also features a change-of-state (COS) function that generates an interrupt when any digital input changes its state.
-
Product
NI-9223, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781398-01
Voltage Input Module
±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9223 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9223: either four, 2‑position screw terminal connectors or four BNC connectors.
-
Product
VME Data Acquistion System
ADM-31
System
The VME-based ADM31 data acquistion system supports up to 48 differential or up to 96 single-ended analog inputs. The ADM31 control card is an intelligent A/D subsystem master or slave device that controls the analog A/D cards. Up to two A/D cards can be configured with the control card to complete the A/D system.
-
Product
4-CH 24-Bit 128kS/s Dynamic Signal Acquisition USB 2.0 Module
USB-2405
Data Acquisition Module
The USB-2405 is a 24-bit high-performance dynamic signal acquisition USB module equipped with 4 analog input channels providing simultaneous-sampling at up to 128 kS/s per channel. The USB-2405 also features software selectable AC or DC coupling input configuration and built-in high precision 2 mA excitation current to measure integrated electronic piezoelectric (IEPE) sensors such as accelerometers and microphones.
-
Product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
-
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
Product
Annunciator
DMS 3K
-
The AMETEK DMS 3K is a flexible, remote alarm management system. It captures alarms from digital or analog inputs, displays alarms on the built-in web server and provides outputs to remote annunciator displays and other devices using serial and Ethernet communications. Alarms can be time stamped to the millisecond for sequential events recording and email notification can be provided for critical events.
-
Product
Temperature and Process Controllers
-
Watlow Electric Manufacturing Company
Temperature and process controllers include one or more sensor inputs with open-loop break detection and multiple outputs for control and alarms. Various configurations offer auxiliary analog inputs, automatic tuning, TRU-TUNE®+ adaptive control, and ramp and soak profiling. Output options include analog process, switched DC and mechanical, solid state and no-arc hybrid relays. Other features include countdown timer, user-customizable menu, burst fire output control, failed heater/load detection and NEMA 4X (IP65, IP66).
-
Product
RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, LAN, DIO (2-in/2-out), 4 AI Channels (16-bit, 250 KS/s) And 2 PCIe Mini Card Slots
IRU152
-
The IRU152 is powered by the low-power NXP i.MX 6 UltraLite processer. It can withstand an extended operating temperature range of -40°C to +70°C and up to 2G of vibration for operating in harsh environments. Furthermore, it supports NI LabVIEW to allow users to design graphical user interfaces for their measurement applications quickly and efficiently. In order to provide data collection and device control, the IRU152 comes with various I/O connectors, including four analog input (AI) channels, one isolated RS-232/422/485 port, one isolated LAN and one isolated DIO (2-in/2-out). The four analog input channels have differential input configuration and overvoltage protection of 55V DC. The maximum sampling rate of IRU152 is up to 250 kS/s with a 16-bit resolution for low-speed high-resolution sensor monitoring and signal measurements. Apart from the abovementioned features, the IRU152 comes in two PCI Express Mini Card slots and one SIM card slot for Wi-Fi, 3G/4G and LoRa connections. The DIN-rail embedded system is equipped with onboard 512MB DDR3 SDRAM; besides, they have an 8GB eMMC flash memory. The extremely low power industrial IoT gateway has passed the Heavy Industrial certification and FCC part 15 to ensure the excellent quality and highly reliable performance.
-
Product
PC/104 Multifunction Analog I/O Boards
104-AIO16A/E
-
The 104-AIO16A is a high-performance 16-bit resolution PC/104 board which provides speeds up to 500kHz for 16 single-ended or 8 true differential analog input channels. This multifunction board features an excellent price/performance value for precision PC/104-based data acquisition, control, or signal analysis of standalone environmental test stations, compact production test equipment, portable testers, avionics and other applications.
