Response
-
product
RGB Digital Fiber Optic Amplifier
CZ Series
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
product
Infrared Gas Detector
GD10 Series
Teledyne Gas & Flame Detection
The GD10 Series has been designed with features that provide an effective response to the detection of gas hazards in a wide range of industrial environments from boiler plant rooms to offshore petrochemical installations.These infrared gas detectors differ from all other models, because they utilize silicon based solid-state infrared sources. The complete optomechanical design and construction is so stable that an ultra fast speed of response can be achieved while providing unparalleled service life and detector stability, thus saving on maintenance and service costs.We offer the longest combined detector and IR source warranty on the market.
-
product
Logger version optical fast DO sensor
RINKO I / I D
Rinko I is an autonomously deployable data logger with a fast response optical DO sensor. The instrument and the software with various operating mode offer flexible observations in the field. The small-sized and the self-contained unit with batteries and a data logger can be easily integrated on platforms (e.g. CTDs). Rinko ID has a depth sensor, allowing for DO vertical distribution measurements.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm
50-294-014
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 4.09k Ohm - SPST
40-294-123
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Molded Interconnect Subtrate
A substrate interposes between an IC chip and a motherboard to enable the IC chip to communicate with the motherboard effectively. Typically, the IC chip is attached onto the substrate and assembled into an IC package before connecting to the motherboard. It is an essential part of the IC package and is responsible for a successful packaging process. Also, it plays an important role in making the IC chip to become a real product and a real solution for end customers. In the past years, semiconductor technologies were highly driven by PC applications which follow Moore’s law in technology migration. In recent years, the emergence of mobile applications increasingly, become the main driver in the semiconductor industry. These mobile applications requires a new kind of substrate that have ability for making IC packages with smaller form factor, thin profile, better thermal, mechanical and electrical performance.
-
product
Optical Detector
LG-9200
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki)The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping.With a compact and light weight body, performances are upgraded compared to the previous model LG-916.(LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
-
product
Gross Gamma Screening System
The Gross Gamma Screening system is intended for the rapid screening of urine samples for the presence of elevated radioactivity in a post-radiological event scenario. This system allows up to eight urine samples to be counted simultaneously in discretely shielded 3” x 3” NaI Well radiation detectors to quickly identify elevated radioactivity from personnel in the exposed population. This screening process provides critical information to Emergency Response Agencies and is accomplished with minimal operator training.
-
product
S2 Ultra High Sensitivity Sensors
ULP-S2 UHS
Universal LightProbe S2 Ultra-High Sensitivity Sensors are designed for the test of very dim LEDs, as low as 0.01 mcd minimum, and including very low light-level LED-illuminated action-indicator switches, controls and status indicators for night/dark viewing in automobile interiors. Recommend the use of wide-aperture stainless- steel encased Fiber- optic Probes with contacting tips.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response times: <190mSFiber-Optic Probes: Wide-Aperture Fiber-Optic Probe recommendedDesigned for the test of very dim LEDs, as low as 0.01 mcd minimum
-
product
Multi Protocol Analyzer
LE-8200A
The LE-8200A is the top-level model of battery-powered communications protocol analyzer. The LE-8200A has an enlarged display in response to an increasing demand without degrading the excellent portability of the LE Series. It is ideal for development tests of communications systems and industrial equipment, as well as for after-sale services and communication trouble analysis.
-
product
Impedance Analyzer
1260A
The model 1260A Impedance/Gain-Phase Analyzer is - without doubt - the most powerful, accurate and flexible Frequency Response Analyzer available today. In daily use by leading researchers wherever measurement integrity and experimental reliability are of paramount importance, the 1260A’s solid reputation is frequently endorsed in published research papers in fields.
-
product
Full-Size Loudspeakers
UPQ
Meyer Sound’s award-winning UPQ loudspeakers have been core components in both portable and installed systems for more than a decade. Characterized by a high power-to-size ratio; smooth, uniform coverage; and consistent polar response; these two-way, self-powered loudspeakers are available in three coverage patterns to fit any application, from FOH mains in small-to-midscale systems to fills in large systems.
-
product
Miniaturized AC Servomotor
Citizen Chiba Precision Co., Ltd.
*Use of Nd magnets allows excellent responsiveness and high output in a compact size.The rotor is evenly balanced to suppress mechanical vibrations.Uses slotless coils which prevent cogging and allow smooth revolutions, even at low speeds. *Miniaturization and inclusion of a high pulse encoder means highly precise positioning is possible.
-
product
Non-Contact Forehead IR Thermometer
Extech IR200
The IR200 is ideal for quickly screening individuals for elevated skin temperature. This infrared thermometer has a non-contact design that eliminates the need for replacement probe covers and other supplies. The IR200 is accurate to 0.3°C (0.5°F) with 0.1°C/°F resolution when measuring skin temperatures between 32.0°C to 42.5°C (89.6°F to 108.5°F). Adjustable alarm alerts user visually and audibly when temperature exceeds programmed limit. Optimum measurement distance of 5 to 15 cm (1.9 to 5.9 in). Move the Body/Surface function switch to the Surface position for non-contact surface temperature measurements from 0°C to 60°C (32°F to 140°F). With a fast response of just 0.5 seconds, users can simply press the trigger and read temperature on the large backlit LCD display. Memory stores up to 32 readings for easy recall. Comes complete with 2 AA (1.5V) batteries and pouch.
-
product
SOP Managemen and Quality Management
arivis BM-Windream
BM-windream is the 21 CFR Part 11 compliant data and document management system for the pharmaceutical industry. It is based on the market leading windream document management system from windream GmbH, Bochum. In addition to our industry-specific modules, we have access to a series of tried and tested windream add-on modules from our partner network, e.g. for e-mail archiving, linking to ERP systems, CRM systems, knowledge management or scanning solutions. BM-windream provides a basis for your data and document management that can be validated at relatively low cost (configurable standard software complying with GAMP5) and is easy to use. Users access your documents using a virtual network drive in Windows Explorer, which means that little training is required. BM-windream provides a standardised user interface over the entire life cycle of a file, from creation to deletion. At all phases in this life cycle, a change history (audit trail) is recorded. BM-windream is suitable for handling all kinds of non-managed documents. BM-Flow integrates directly with BM-windream and provides the document management functions required for SOP management,manufacturing instructions etc. All general employees can then still access the documents using the familiar Windows Explorer, while those responsible for creating documents can also use the workflow interface in BM-Flow.
-
product
True Dual-Channel Analysis on iOS
IOScope
With IOScope, measure loudspeaker impedance, frequency response, and sensitivity. Measure a room impulse response. Tune a large sound reinforcement system, time-align a set of surround sound speakers, or optimize your home stereo. Determine the actual cutoff frequencies of your latest speaker crossover circuit, or teach your students the fundamentals of Fourier analysis of dynamic systems.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm - SPST
50-294-124
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
VFTLP+ Test System
4012
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
product
pH 550 Benchtop pH Meter Kit with Probe, Stand, and pH Buffers
The PH 550 benchtop pH meter features a microprocessor chip which provides automatic temperature compensation, data storage, parameter setup, and Max/Min reading display. The meter offers a pH range from 0 to 14 and a three-point automatic calibration, with the ability to recognize standard buffer solutions (USA or NIST series). The advanced digital processing technology improves meter response time and measuring accuracy. A stable reading display icon appears when the measuring value is stable. The 3-in-1 combination pH electrode measures pH and temperature simultaneously. The compact meter includes a detachable electrode holder and three bottles of pH buffer solution. It has a dustproof and spillproof rating of IP54. Connectors are protected by silicone seal caps.
-
product
Combined Illumincance and Irradiance Probe
LP471P-A
Combined probe for measuring ILLUMINANCE (lux), with standard photopic response, and IRRADIANCE (μW/cm²) in the UVA spectral range (315…400 nm, with peak at 360 nm).
-
product
Test Data
Studies by major universities were conducted in response to a request from the military, scientific and engineering communities for scientific validation of claims that Pulse Technology actually improves battery efficiency and lengthens battery life. PulseTech contracted with Oakland University in Rochester, Michigan and Ohio State University in Columbus, Ohio to conduct separate evaluations of the technology. These extensive evaluations began in the summer of 1998 and concluded in the fall of 2000.
-
product
Very Low Pressure Variable Reluctance Sensor
DP103
The Validyne DP103 is designed for exceedingly low differential pressure measurement applications where high accuracy is required under rough physical conditions. With full scale ranges down to -0.008 psid (-0.56cm H2O), this instrument is being used in the measurement of very low flow rates of gases where symmetrical pressure cavities are required for dynamic response. It is also used in very small leak detection and pressure null detection systems.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm - SPST
50-294-134
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Comparators
General-purpose comparators utilizing CMOS process suitable for low voltage, low power consumption, and fast response.
-
product
Thermometers
T1-T2 Function, Data Hold Function, Temperature Alarm Function, Adjustable Auto Power Off Timer, Fast Response With High Accuracy
-
product
PCI Resistor Card 2-Channel 2 Ohm To 131 Ohm With SPDT
50-293-134
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
product
Solar Array Simulator
G5.SAS
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
product
Modal tests
Modal Testing and Modal Analysis - SIMO, MIMO, and ODSEffective and affordable modal testing and analysis solution for SIMO, MIMO, and ODS testing methods. The modal test is an indispensable tool to determine natural frequencies and mode shapes of any structure. With our solution, you are able to excite the structure with an impact hammer or modal vibration shakers and easily measure the responses. Import or draw your geometry for rich visualization and animation of your structures.
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
