Circuit
-
Product
Split-Core Current Transformers
CTS Series
-
Continental Control Systems LLC
The CTS series CTs are available with windows from 0.75 inch up to 2.0 inch. They have a removable section, so that they can be installed without interrupting the circuit. 0.333 Vac output at rated current Accuracy ±1% from 10% to 100% of rated current Phase angle <2° degrees at 50% of rated current (valid for 70 A or higher) 8 ft. twisted-pair wire, 600 Vac rated UL recognized for voltages up to 600 Vac, CE mark, RoHS
-
Product
5 Inputs Satellite Multi-Switch
HJMS-500B (Stand alone)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*4 satellite IF & 1 terrestrial TV inputs. *Built-in amplification circuit to compensate cable loss. *13/18V.22KHz switching. *Suitable for residential multiple LNBs reception.*Sheet Metal Housing.
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Trip Indicator Relays
TIR
-
The TIR relays are designed for event recording circuit applications, where high speed event monitoring is required. The TIR relay contacts are used to record breaker functions, relay, communication and control system operations. The TIR contacts are also used to activate alarm and/or annunciator contacts.
-
Product
Small outline PCB with 72 Pin Socket
1091-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Loudspeaker Cable Testers
EMO E450
-
The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.
-
Product
Multi-Stage Functional Test Systems
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
Product
80 Channel Relay Multiplexer
DP-VXI-4017
-
DP-VXI-4017 is an 80 Channel Relay Multiplexer constructed using ‘2 Form A’ (DPST) relays. It is a ‘C’ size 1 slot register based VXI module. This 80 Channel Relay Multiplexer module is highly configurable. As an 80 channel multiplexer, one input can be multiplexed to any of the 80 outputs or vice versa. The 80 channel multiplexer is divided into 8 banks of 10 channels each. This combination allows the board to be used as one group of 80x1 or two groups of 40x1 or four groups of 20x1 or eight groups of 10x1 differential multiplexer. The banks are isolated from each other by tree switches. 8 tree switches are used, one tree switch for each bank. A common tree switch is used to group all the eight banks. For short circuit protection resistors are provided for all the common terminals.
-
Product
EOL Testing of Starter-Generator Units (ISG)
-
Series test rig for starter-generator units (ISG)*High voltage test*Insulation resistance measurement*Temperature sensor control*Short circuit test*EMF test*Performance measurement*Manual loading and contacting
-
Product
BGA Socket And BGA Adapter Systems
-
Mill-Max's BGA Socket/Adapter Systems are used for both socketing BGA devices and interconnecting circuit boards. Systems are available to fit 1mm, .050" and .8mm grid footprints.
-
Product
250 MHz Passive Probe for WaveSurfer3000, 10:1, 10 MOhm
PP019-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP023-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
Digital Tachometer - Non Contact / Contact / Non Contact & Contact
MODEL - KM- 2234BL / KM 2235 B / KM 2241
-
Kusam Electrical Industries Limited
Digital Tachometer uses latest technology for accurate measurements. It has Exclusive one chip of Microcomputer LSI Circuit, It is housed in tough ABS case & has ergonomic design for easy holding in the hand.
-
Product
General Purpose Basic Carrier Demodulator
CD15
-
The CD15 Sine Wave Carrier Demodulator operates with variable reluctance transducers to provide a DC output signal for dynamics as well as steady state measurements. A 5kHz sine wave excitation is applied to the two inductance ratio arms of the transducer and the resulting output is demodulated and amplified using the latest integrated circuit techniques. The DC output is obtained from an active filter circuit and gives a uniform response from steady state to 1000 Hz. The low impedance sine wave excitation allows operation with the transducer located over 1,000 feet from the CD15.
-
Product
LIGHT RANGER MUTT
TT9103
-
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
Product
Premise Toner Drop Cable Continuity Tester
RPT-AAA Series
-
Electronic testing tool designed to check the circuit integrity in new or installed cable up to 5,000 feet (1,500 meters) in length LED indicates DC shorts, splitters & other self-grounding devices in cable while a loud audio tone identifies the line carrying the signal Equipped with a right angle male push-on connector to maneuver in tight areas & a female push-on connector for speed toning Tool includes a pocket clip & (1) AAA 1.5V battery.
-
Product
Power Electronics Solutions
-
Scientech Technologies Pvt. Ltd.
Power electronics has found an important place in modern technology being a core of power and energy control.The subject of Power Electronics is the merger of the field of electrical power system and solid state electronic devices. It is the discipline that involves the study, analysis, and design of circuits that convert electrical energy from one form to another. Almost all the new electrical and electromechanical equipment contain power circuits.
-
Product
Programmable Current Preamplifier
99539
-
The Model 99539 is a modular, multi-channel current preamplifier with parallel, logic level, gain control input. It consists of circuit boards which plug into a 3 1/2" high by 19" wide rack chassis.
-
Product
ATE Development
-
Aero Engineering Support Group
ATE Development Aero Engineering Support specializes in designs and manufacturing of a wide variety of Automatic Test Equipment (ATE) of support for military avionics, commercial avionics, industrial sector, etc. AESG is committed to providing industry leading equipment that are designed to be scalable and expandable ATE capable of providing reliable functional test solutions for any electronic assembly or Circuit Card Assembly. New from Aero Engineering Support is the A2500 system, providing:
-
Product
Door Contact Sensor
ENVIROMUX-M-DCS
-
Monitors access with a magnetic bridge sensor, which responds to any magnetic material (no special inserts necessary). Can also be used for monitoring side wall and covers. Includes mounting hardware. For normally closed circuit connection. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft. Wide actuating gap, approximately 1". Dimensions WxDxH (in): 0.5x0.5x2 (Switch), 0.5x0.5x2 (Magnet). Operating temperature: 32 to 158°F (0 to 70°C). Regulatory approvals: RoHS.
-
Product
PCIe Gen3 4K Compact, High Speed Camera for Testing
CB120MG-CM-X8G3
-
4K, compact, high speed camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
Product
400/5A CHEAP SPLIT CORE CAST RESIN CURRENT TRANSFORMER
LZCK310-10
-
Beijing GFUVE Electronics Co.,Ltd.
LZCK series outdoor waterproof current transformers are applicable for AC power system 35kV and measurement of current of power supply equipment below 10KV also can be used for microcomputer protection. This type of current transformer employs imported silicon steel which with high permeability as magnetic material, has the characteristics of Small magnetic circuit loss and can be split, its semicircular core and secondary windings employ high quality epoxy resin vacuum, casting in plastic-case(ABS or PC) which is flame retardance anti-moisture, stable performance, no maintenance.
-
Product
Injection Transformer
J2100A
-
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 122Ω
40-251-012
Programmable Resistor Module
The 40-251-012 is a programmable resistor module with 8 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXI RTD Simulator Module 12-Channel PT1000
40-262-202
Simulator
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
Universal Development Board For The Plug-in Module PCAN-MicroMod FD
PCAN MicroMod FD Evaluation Board
-
The PCAN-MicroMod FD Evaluation Board is a development board for the PCAN-MicroMod FD and enables the design and development of your own circuits with CAN connection and I/O functionality. It can also be used for training purposes for CAN and CAN FD structures. The user can access the resources of the attached PCAN-MicroMod FD via taps, screw terminals, switches and potentiometers and test configurations or test circuits.
-
-
Product
Circuit Breakers
-
As the premier supplier of power system components, Interpower has what you need to complete your projects, including circuit breakers. Interpower has no minimum order requirements, plus same day shipping is available on in-stock Interpower products.
-
Product
Chip Scale TVS Arrays
-
ProTek's patented* Flip Chip TVS Arrays are designed for small circuit board applications with limited size and space availability. To reduce installation costs, the Flip Chip can be mounted directly onto the printed circuit board; similar to chip resistors and capacitors. These devices are ideal for use in portable electronics such as Cellular Phones, Cellular Phone Accessories, Personal Digital Assistants (PDAs), Laptops and Pagers.
-
Product
Logic analyzers, MSOs
-
This digital logic analyzer has basic functions, easy operation and a new way of measuring data for monitoring and measuring signals in digital information processes. Thus, the device allows the analysis and troubleshooting in digital systems, such as transmission delays to be analyzed and the result of the information processing of the digital circuit and bus technology.
