Filter Results By:
Products
Applications
Manufacturers
Low Pass Filters
Refine signal, allowing the transmission of signal below a specific corner frequency, while attenuating the frequencies above.
See Also: Filters, Filter / Amplifiers, EMI Filters, Programmable Filters
-
product
Low-Pass Filters
Is a filter that passes signals with a frequency lower than a selected cutoff frequency and attenuates signals with frequencies higher than the cutoff frequency. The exact frequency response of the filter depends on the filter design.
-
product
Low-Pass Filters
Low-Pass Filters from Analog Devices are specifically designed to reject higher frequency noise and unwanted signals while allowing desired signals to pass through. Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) devices preconfigured for low-pass filtering. These integrated low pass filters feature a wide range of cutoff frequencies and response characteristics.
-
product
Precision Analog Anti-Alias Low-Pass Filter Board
GSAF-10
The GSAF-10 Gold Series are analog low-pass filter boards that offer the performance required to maintain the maximum accuracy of high-precision 16- and 18-bit A/D converters.
-
product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Lowpass Filters
Frequency range of this lowpass filter is DC to 100 MHz and the passband is 100 MHz. PE8719 lowpass filter is one of over 40,000 RF, microwave and millimeter wave components supplied by Pasternack. Our 5 section low pass filter can be bought and shipped worldwide the same-day as with our other in-stock RF parts.
-
product
Frequency Counters
-Frequency Range : 0.2Hz to 5.5GHz Built-in CMOS Gate Array Fast, High-Resolution, 10 Digits Green LED Display Microprocessor Controlled Reciprocal Technique for Low Frequency Resolution Self Diagnosis Routine Total, RPM Function, Period Low Pass Filter(100KHz, -3dB) Rs-232c Interface(Option)
-
product
1.3GHz Frequency Counter
Model 1122 / 1122X
- Wide Frequency Range 0.2Hz to 1.3GHz- 2 Separate Channels, for LOW & HIGH Frequencies- High Sensitivity- 8 Digit Green LED Display- Microcontroller based Advance Technology- Optional RS232 Interface- Reciprocal Counting Technique for High Resolution at Low Frequency- Period Measurement- Low Pass Filter for Noisy Low Frequency (<100KHz)- 4 Selectable Gates (10ms, 100ms, 1sec, 10sec)
-
product
Programmable, 2-Channel Low-Pass Filter Module
AAF-2Fe
Programmable, 2-Channel Low-Pass Filter Module. The AAF-2Fe may be used with the AAF-3PCI, AAF-3, AAF-2, or AAF-1 filter boards.
-
product
Precision Low-Loss Multiplexers
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.Power handling is rated at 100W CW (average) and typical insertion loss is better than 0.5dB between the low-pass (Fo) and common ports.DP- and TP-series multiplexers are ideal accessories for passive, active and hybrid-active multi-harmonic load pull systems.
-
product
High Speed Data Acquisition Board
MS 1800
*Bus Interface:- 64 Bit PCI Bus with PMC Interface*Virtex-4 FPGA based design*32 channel digital I/O signal*RS232 & RS485 Interface*32MB Flash*2MB Static RAM for data storage*Analog Inputs:- 2 Channel*Input Resolution:- 14 Bits*Sampling rate up to 80MSPS*Filter:- Low Pass Filter for all channels*Two Analog Outputs*14 bit Resolution*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
product
1 MHz Bandwidth Voltage Preamplifier with Bandpass Filter
EC6081 mk2 - preamplifier
The EC6081 mk2 (VP2000) is a 1MHz bandwidth voltage preamplifier with bandpass filter that is designed for uses in conjunction with piezoelectric hydrophones. VP2000 offers excellent low-noise performance over the entire frequency range; and adjustable gain selection. A range of 12 high-pass and 12 low-pass filters are available, these allow ideal band pass filter settings.
-
product
ACDC
EC Series
The EC Series of line operated power supplies features near constant efficiency over theentire rated input voltage range. These electrically identical families employ a highly efficient, closed loop ripple regulation circuit, which contains a low pass filter. Each stage, transformer, filter and regulator is engineered for maximum efficiency.
-
product
Amplifier/Filter Module
SCS-818
The SCS-818 and SCS-819 amplifier/filter module provides eight 4-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-818) and 0.5Hz to 70kHz(SCS-819). Each of the SCS-818/SCS-819's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
PXIe-4300, 16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module
781337-01
16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module—The PXIe‑4300 provides integrated data acquisition and signal conditioning for high-voltage measurements. It provides increased accuracy, simultaneous sampling, and synchronization features for scalable measurement systems. The PXIe‑4300 includes 300 Vrms channel‑to‑channel CAT II isolation and 3,300 Vrms channel‑to‑earth 5 second withstand isolation to protect users and equipment from hazardous voltages. This module offers programmable lowpass filtering, DC input coupling, and two PFI lines for digital input triggering. The included NI‑DAQmx driver simplifies hardware and configuration and measurement.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
"Standard" RF Low Pass Filters
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
product
Low Pass and Bandpass SMA Coaxial Filters
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Lowpass Filters
K&L Microwave provides lowpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
product
Ethernet A/D Interface
2518/2519TDIN
8 or 16 differential thermocouples, RTD's, strain gauges, thermistors, resistance, 4-20 ma, or voltage inputsIncludes screw terminals for field wiring10-Base-T Ethernet server with embedded TCP/IP stackIncludes interface DLLSingle supply operationEach channel is software programmable for sensor type, gain, low-pass filtering, scan rateOptional NEMA Enclosure
-
product
Handheld Digital Multimeter, 4 digit, Water and Dust Resistant
U1271A
Feature sets that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.7% for ACV accuracy)Intelligent features to improve productivity and safety (selectable Low Pass Filter LPF and quick signal type identification Qik-V)Better grip Both visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 200) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
product
Smart Analog to Digital
618/619
Supports thermocouples, RTD's, strain gauges, voltage in, 4-20mA, thermistors, and resistorsUp to 16 differential input channels plus sensor excitationEach channel is software programmable for sensor type, gain, low-pass filtering, scan rateAuto-calibration eliminates trimpotsLow power consumption
-
product
Single Channel USB Programmable Band-Pass Filter
USBPBP-S1
The USBPBP-S1 stand alone USB controllable module provides a single channel of high and low-pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPBP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPBP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPBP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
product
High-speed USB DAQ System
Model DI-4208
USB Data Acquisition (DAQ) System. Eight armored analog differential inputs*. Programmable range per channel: ±2, 5, 10, 20, 50 100 V full scale. Up to 120 V rms without damage. 50 dB common mode rejection. Supports ChannelStretch™ multi-unit synchronization*. Adaptable low-pass filter per channel. Corner frequency set as a function of sampling rate. 16-bit analog-to-digital resolution. 160 kHz analog sample throughput rate. Seven digital ports*. Programmable per port as input or switch. Support for rate measurements to 50 kHz. Support for 16-bit counter.
-
product
Active Filter
J2190A
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Filtered Analog Input Expansion Board
MSXB 048
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
product
Dual Channel 180 MS/s Digitizer PXI / PXIe Card
GX2482
The GX2482 series are a high performance, dual differential channel, 16-bit digitizer offering high dynamic range and excellent SFDR. The module’s differential inputs, coupled with its low distortion makes it an ideal instrument for analyzing high performance or low level analog signals. Each channel offers 3 selectable low pass filters, a 16 bit, 180 MS/s ADC, and 64 M words of memory for each channel.
