Force
exerts an influence.
See Also: Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Lead Free Probe
LFRE-1T24-6
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Linear Stages
-
A new set of motorized tables developed by Klocke Nanotechnik allows high strokes at small volumes. The modules are driven by the Nanomotor®. Loads of up to two kg can be moved over centimeters of stroke with down to 2 nm resolution. Manipulation in many degrees of freedom is possible without backlash. The modules NMT xx-L are longer, but thin like a pencil. In most of the NMT-modules position measurement systems can be included without increasing the size. The resolution of the position sensor is better than 10 nm. All NMT modules can easily be fixed onto each other. Very small connectors allow the exchange of a module without removing cables. The NMT-Zxx are modules for vertical movement. They have an internal load compensation to lift up loads. Nanomotor-Grippers and force sensors that can easily be fixed on these modules are available.
-
Product
Vertical Probe Cards
B3
-
The patent-pending B3™ structure requires a minimum number of parts and can handle up to 300 probes. This vertical technology can provide: • Increased Uptime • Extended Probe Lifetime • Reduced Maintenance • Lower Cost of TestThe B3™ is an ideal solution for testing small pads and the low force probes minimize scrub. Planarity also remains stable over time increasing probe card life. Contact your sales representative to learn more about our B3™ probe cards.
-
Product
Burn-in Board Continuity Tester
CT-1
-
Burn-in Board Coninuity Tester. Verifies burn-in board continuity and component tolerances. 768 I/O channels, can be forced to the constant current source or grounded independently. Highly accurate measurement of resistance, voltage, and capacitance using a pair of precision instrumentation amplifiers.
-
Product
250W to 400W - Single Output
CUS400M Series
-
*250W Convection / Conduction Cooled*400W with Forced Air*Medical Certifications (2xMOPP)*Class B Conducted and Radiated EMI*Suitable for Class I and Class II installations*Compact 3 x 5 x 1.55" size*Enclosure & Signal Options
-
Product
Test Finger Nail Probe
CX-75
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Finger Nail Probe is indicated test IEC60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the neccessary force for using the instrument. This probe is make of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.
-
Product
UL496 Screw Lampholders Torque Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
Screw lampholders torque tester is strictly designed according to UL496 etc. It's mainly used to the screw lampholder torsion test of protecting accidental force.
-
Product
Rugged, Long Gauge Length Extensometers
Model 3543
-
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged flexures within the unit. This unique design allows long measuring ranges, yet retains compatibility with electronics for strain gaged transducers. These models offer high accuracy and are light weight but rugged, with low operating force. They are tension only units.The units have hardened tool steel knife edges. Standard quick attach wires provided with the extensometer work on flat specimens up to 12 x 31 mm (0.5 x 1.25 inch) and on rounds up to 25 mm (1 inch) diameter. Optional quick attach kit wire forms are available for use on larger samples. See Model 3542L for long gauge lengths with smaller measuring ranges.The Model 3543 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Compression Load Cells
-
A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.
-
Product
Forced Air Cooled RF Coaxial Loads
86700 Series
-
The 86700 Series Forced Air Cooled RF Coaxial Loads are capable of dissipating up to 75 kW of CW RF power from DC Hz to 240 MHz with a VSWR of 1.15:1 or less. With this low reflection coefficient the loads are very useful for tuning transmitters.
-
-
Product
Analytical Services
-
Atomic Force Microscopy (AFM) allows for sub nanometer resolution imaging of surface topography and is able to quantify surface roughness at the angstrom scale. Our team can give you highly accurate measurements such as surface topography, dopant distribution, magnetic domain features, and a wide variety of other sample properties to give you the information you need to do great work.Park can provide measurements in the following areas:● Topography (surface roughness, grain size, step height, etc.)● Mechanical Properties (stiffness, etc.)● Electrical properties (capacitance, conductivity, etc.)● Thermal properties ● Magnetic properties These properties can be measured in air or liquid, depending on your needs.
-
Product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-1L24-2
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 26-30 AWG
610138112
-
Primary mating contact 610138116. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.
-
Product
Micro Vickers Hardness Tester
900-392
-
The 900-392 Micro Vickers Hardness Tester is engineered to produce a clearer indentation and hence a more precise measurement. By means of a 10 × lens and a 40 × lens the 900-392 vickers hardness tester has a wide measurement field and a broad usage range. Equipped with a digital microscope, it shows the measuring methods, the test force, the indentation length, the hardness value, the dwell time of the test force as well as the number of the measurements, all shown on its LCD screen.
-
Product
Ultra High 3.83 (109.00) - 10.00 (283.00) High Performance Lead Free Probe
LFRE-72I15-10
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,700Overall Length (mm): 43.18
-
Product
Electrodynamic Shakers | Electrodynamic Shaker Systems
-
Wewon Environmental Chambers Co, Ltd.
Your product descElectrodynamic shakers makes use of an electro-mechanical assembly to product vibration through electromagnetic force. These electrodynamic shaker systems can precisely generate either single, or multi-axis vibration using sine, random, sine-on-random, or random-on-random accounts. Usually these ED shakers are utilized to figure out the products ability to either run within it’s intended environment, or to target resonance in the product to determine weakness.Any type of product moved by road, sea or air, is subjected to vibration tests throughout its manufacturing procedure. These tests supply essential details relating to the behavior of the manufactured part before advertising and marketing, in order to prevent them breaking in the future.All the vibration tests, both vertical and also horizontal, may furthermore go through temperature as well as relative humidity tests, integrating the vibration test with making use of a climatic chamber. The electro dynamic shakers from Wewon attach to any kind of electrodynamic vibration system. https://www.wewontech.com/electrodynamic-shakers/
-
Product
Amplifiers And Linear ICs
-
For the simplest to the most complex designs, our extensive portfolio of amplifiers and comparators enables you to develop low-risk solutions with minimal risk of a forced redesign. These devices are also backed by our client-driven obsolescence practice of continuing to supply a product for as long as possible and while demand for the product exists.
-
Product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-1I40-2
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
3-DOF Simulation Table
KRD60 series
-
KRD60 Series 3 DOF simulation table simulates various mechanical, electrical, and electronic products installed on ships, seaplanes, and other equipment to perform sway and tilt tests to determine the ability and structural integrity of the product to withstand severe sway and tilt requirements. The tilt test is mainly applicable to large-angle tilt caused by ship damage, manipulation, imbalance in loading and unloading, and wind. The sway test is mainly applicable to long-term swaying of the ship due to external forces such as wind and waves, which must be maintained normally or products that work reliably, and products that have a significant impact on their performance in a rocking environment.
-
Product
Keyboard Button Testers
-
Infinity Machine International Inc.
Keyboard Button Testers by Infinity Machine International Inc. - for applications such as keyboard button compression force tester, keyboard durability test machine, adjustable keystroke life-span tester, mechanical keyboard switch tester, computer keystroke tester, button force testing, key stroke force tester for load stroke curve test, rubber keystroke tester, and more.
-
Product
Crypto Devices
-
Confidential communications are essential to armed forces and government authorities. The Rohde & Schwarz crypto devices provide secure end-to-end encryption for the secure transmission of sensitive information over public communications networks or radio transmissions. Rohde & Schwarz crypto devices are interoperable with HF/VHF/UHF radios, satellite communications and line transmission equipment. They can encrypt and decrypt voice and data communications at the highest security levels. The crypto devices are ideal for stationary and mobile platforms in rugged terrain and in naval and airborne environments.
-
Product
Force Tensiometer
K6
-
Our Force Tensiometer – K6 is a robust and reliable manual instrument for measuring surface tension and interfacial tension using the ring method. As a quality product from our precision mechanical workshop, it produces fast, easy and accurate measurements for surfactant solutions and solvents.
-
Product
Adhesion and Peel Tester
-
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
Product
ICT Probes
Merica Serirs- MP175
-
Minimum Center: 1.91mm (75mil)Current Rating: 3amps, continuousContact Resistance: 40milliohmsMounting Holes Size: 1.35Full Stroke: 6.40mmRated Stroke:4.30mmSpring Force: 203gf (7.2oz)/227gf(8oz)
-
Product
Displacement Transducers
-
Procter & Chester Measurements Ltd
Pressure: Measures gas or liquid pressure. Pressure is an expression of the force required to stop a fluid from expanding. The transducer generates a signal from the pressure imposed upon it.Torque: Measures the torque (or twisting motion) on a static or rotating system. The static torque element has little movement and therefore more economic to manufacture and purchase. Rotary or dynamic torque is more complicated as the signal needs to be transferred using slip rings, wireless telemetry or rotary transformers/inductance technology so that the strain gauged shaft can continuously rotate.Displacement: Measures distance. The displacement transducers that PCM offer are slightly different to standard units. They have a strain gauge/wheatstone bridge. The benefit here is that if the customer has existing electronics that uses strain gauge/load cell technology, they can use them with these sensors.
-
Product
Air-bath Film Heat Shrinkability Tester
DRK166
-
Shandong Drick Instruments Co., Ltd.
DRK166Air-bath film heat shrinkage performance tester, according to ISO14616 air heating principle test method to test the shrinkage performance of heat shrinkable films of different materials, to study the relationship between heat shrinkage force and cold shrinkage force of heat shrinkable films of different materials, and to determine the direction of the test when shrinking.
-
Product
Auto Tensile Tester
ATT-01A
-
Jinan Leading Instruments Co., Ltd.
ATT-01A Auto Tensile Tester is applicable in the test of physical mechanical properties of plastic films, laminated materials, adhesives, adhesive tapes, adhesive bandage (plaster), release paper, protective film, leather, rubber and paper fiber, etc. It can perform the test items of tensile, peeling, deformation, tearing, heat seal, adhesive, open force, etc.
-
Product
Electromechanical Testing Machines
-
Stand model in four-pillar design with electronic force transducer, flanged to the movable testing machine crosshead and electronic position transducer for measuring the crosshead path. The machine is driven by a quartz-precise stepper motor with two ball screws. Complete with integrated displacement measuring device 0.01 mm over the entire travel distance as well as additional displacement transducer with connecting cable and holder
-
Product
Countermeasures Dispenser Testers (CDT)
-
The nation’s Air Force, Army, Navy, Marine Corps, and key government agencies all depend on countermeasure dispensing systems – including the AN/ALE-47 and others – aboard their aircraft for self-protection against missile attacks and other airborne munitions. Especially when operating in contested areas, a properly-functioning countermeasure dispensing system can make all the difference to the success of a mission. That’s ample reason for aviation maintenance and flight prep crews to prefer the unmatched reliability of BAE Systems Rokar Countermeasure Dispenser Testers (CDT) for keeping their countermeasure dispensing systems performing effectively and safely.
