Programmable Logic Controller
Programmable Logic Controller
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-156
-
The 40-297A-156 (PXI) and the 42-297A-156 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 85.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm
50-294-014
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Resistor Module Dual 12-Channel (no resistors fitted)
40-281-021
-
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 3Ω to 22.3MΩ
40-251-154
-
The 40-251-154 is a programmable resistor module with 1 channel which can be set between 3Ω and 22.3MΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
JTAG USB Controller
NetUSB-1149.1/E
-
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
Product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 201kΩ
50-297-041
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 122Ω
40-251-012
-
The 40-251-012 is a programmable resistor module with 8 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 26.7kΩ
50-298-132
-
The 50-298-132 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 26.7kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1.5Ω to 1.81kΩ
40-252-022
-
The 40-252-022 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 3.55kΩ
50-297-023
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-143
-
The 40-297A-143 (PXI) and the 42-297A-143 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 773 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 62.1Ω
40-252-111
-
The 40-252-111 is a programmable resistor module with 2 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
AXIe High Performance Embedded Controller: 2.8 GHz Quad-Core, 8 GB
M9537A
-
The M9537A is a second-generation AXIe embedded controller which enables new capabilities such AXIe wide PCIe support, multiple 4K video outputs, and optional high speed disk cache. It is designed for high performance, compact AXIe systems.The embedded controller is a powerful, one-slot module that easily integrates into hybrid test systems using the GP-IB, USB, and LAN front panel interfaces. Built upon a high-performance Intel Core i7 quad-core processor with Hyper-Threading Technology, it is perfect for high-performance applications and multi-tasking environments.
-
Product
cRIO-9038, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller
783850-02
-
1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9038 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9038 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. Additionally, the cRIO-9038 supports an extended temperate range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
PCI-8366, PCI Host, 100 MB/s, Fiber-Optic Cable MXI-Express Device for PXI Remote Control
781400-01
-
The PCI‑8366 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8366 remote controller provides a PCI link over a fiber-optic cable to the PXI‑8368 remote control module when used for PXI system control. Fiber-optic remote control solutions are ideal for long‑distance‑device control and electrical isolation. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 472Ω
50-297-120
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
68-Channel Portable Logic Analyzer
16862A
-
68 channels, 350 MHz state, 12.5 GHz timing zoom, 2.5 GHz timing, 2 Mb depth standard15-inch (38.1 cm) color, touch-screen display for viewing and quickly navigating large numbers of signals and buses Built-in removable SSD drive, USB 3.0 ports and LAN for fast data transfer and storage of large amounts of data1.4 GHz trigger sequencer to ensure high-speed events are captured
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm - SPST
40-294-122
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-110
-
The 40-297A-110 (PXI) and the 42-297A-110 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 31 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 470Ω
40-251-014
-
The 40-251-014 is a programmable resistor module with 8 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 3.5Ω to 773kΩ
40-298-043
-
The 40-298-043 is a high density programmable resistor module with 6 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-116-HI
-
The 40-230-116-HI (PXI) and 42-230-116-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 1.8kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 13.6kΩ
40-251-031
-
The 40-251-031 is a programmable resistor module with 4 channels which can be set between 2Ω and 13.6kΩ with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Resistor Module 2-Channel 2R to 131k
40-293-034
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-114
-
The 40-297A-114 (PXI) and the 42-297A-114 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 470 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Transient Suppression for Corelis JTAG Controllers
TAP Protection Adapter
-
Transient events such as Electrostatic Discharge (ESD), inductive switching, and lightning can damage electrical equipment, leading to costly repairs and test equipment down-time, reducing production capacity and increasing time-to-market.The Corelis TAP Protection Adapter is designed to enhance protection to any Corelis JTAG controller, shielding against harmful events using a combination of electrical defenses.The compact adapter features series resistors and transient voltage suppressor (TVS) diodes to mitigate damage to the JTAG controller. Protect your investment and enjoy peace-of-mind with the TAP Protection Adapter.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm
50-294-031
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
787987-01
-
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
PXI Potentiometer Module 5x8 Bit, 0 Ohm to 255 Ohm
40-296-021-5/8
-
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
PCI High Density Pecision Resistor Card
50-298-024
-
The 50-298-024 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 6.97kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
