Impulse
-
Product
Impulse Hammers
-
Impulse hammers are designed for frequency measurement of mechanical structures, such as mechanical mobility, mechanical damping and impedance.
-
Product
IMPULSE SURGE WINDING TESTER
VE2882A-5U
-
Impulse Tester can detect turn & layer short ,the differences in the number of turns and the material of the core. If high impulse voltage is applied, the poor insulation will appear as a corona or layer discharge.
-
Product
Impulse Voltage Generator
-
Shanghai Sanki Electronic Industries Co., Ltd.
Impulse voltage generator Impulse voltage generator is mainly used for test products such as power equipment to perform lightning impulse voltage full wave, lightning impulse voltage chopping, operating impulse voltage wave and steep wave impulse voltage test, to inspect insulation performance. The technical indicators comply with national standards and IEC standards.
-
Product
Impulse Test Equipment
-
mpulse test equipment for testing of low-voltage rotator windings.The equipment is composed of a surge impulse generator circuit, phase selector unit (selection between U, V and W), and waveform recorder circuit to provide a differential method type of impulse testing instrument.
-
Product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
-
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
Product
Impulse Meter
-
*coil testing for motor and transformer *judge quality by comparing wave difference *LCD display
-
Product
Impulse Generator
CTS-10350
-
The CTS-10350 is an impulse generator with a current wave shape 10/350 μs at the output terminals. Dual outputs enable testing of 2 terminal devices and 3 terminal devices up to class 1. The generator impedance is 1ohm in dual output mode or 0.5ohm when both outputs are connected together.
-
Product
Impulse Voltage Generator
GDCY
-
The impulse voltage generator is mainly used to the field of impulse voltage tests by lightning impulse voltage full wave, lightning impulse voltage chipped wave and operate impulse voltage wave for such test products as electrical instrument.
-
Product
Impulse Sledge Hammer
-
Impact hammers are designed to measure the frequency of mechanical structures, such as mechanical movement, mechanical damping and impedance.
-
Product
AC & DC Combined Test Set With / Without Impulse
-
This testing equipment is used in electrical and power industry.
-
Product
Impulse Response Measurements
Dirac
-
Dirac is a sophisticated tool to calculate a very wide range of acoustical parameters from impulse response measurements of an enclosure. Through many years of development and customer feedback, Dirac has grown to support many different applications. Due to its user friendly interface it is suitable for field measurements, but it also contains many advanced features that make it useful in a laboratory or research setting.
-
Product
Digital Impulse Voltage Measuring System
TR-AS
-
The well-established Impulse Voltage Measuring Systems TR-AS, including the digital recorders from our own development and manufacturing, where further developed consequently and now feature improved sampling rates up to 200 MS/s in real-time with 14 Bit resolution simultaneouly in up to 16 measuring channels.
-
Product
High Voltage Impulse Test Set Up
-
We are renowned as the foremost manufacturer and exporter of High Voltage Impulse Test Set Up. This testing equipment is demanded in electrical, power generation and engineering sector. It is incorporated with fiber optic isolated digitizers to test various types of transformers. We utilize excellent grade raw materials to engineer and develop this High Voltage Impulse Test Set Up in accordance with industry standards. Our clients can get this equipment from us at competitive price.
-
Product
Impulse Current Test Systems
-
Fivestar HV Testing Equipment Co., Ltd.
Impulse current test systems are mainly used for testing transmission and distribution systems against the effects of direct or indirect lightning strokes or against electromagnetic interference effects. Primary application of impulse current test systems is the testing of surge arresters, nowadays mainly of the metal-oxide type (MOA) and surge protection devices (SPD). Now they are also widely used to test vehicles, aircrafts, and military applications.
-
Product
Impulse Withstand Voltage Tester
SUG255
-
The Impulse Withstand Voltage Tester (or High Voltage Surge Generator), it is according to IEC255-5, IEC60060, IEC60065, GB14711, GBT17215.301 and GBT17215.322. It is suitable for doing all kinds of electrical and electronic products (such as energy meter, household appliances, low voltage electrical appliances and small power motor) insulation performance test.
-
Product
FPGA Impulse Response (FIR) Filter Fo Gage Digitizers
eXpert / Finite Impuls Response (FIR)
-
The onboard FIR Filtering eXpert FPGA DSP feature is a powerful method for removing unwanted signal features (like noise) and emphasizing signal features of interest.
-
Product
Edge Impulse
-
The leading development platform for building, optimizing, and deploying machine learning models directly on edge devices.
-
Product
Impulse Tester
MIG2412SPD
-
The MIG2412SPD is a impulse tester for testing SPD (Surge Protection Devices) in accordance with IEC 61643-1 and VDE 0675. Up to maximum 24kV/12kA making it suitable for testing Class I to III or in accordance with VDE Class A,C, D. The MIG2412SPD is a hybrid generator with a voltage wave shape 1,2/50 ìs at "no load" and a current wave form 8/20 ìs at short circuit for testing Class III (D) SPD connected to power line.
-
Product
IMPULSE VOLTAGE GENERATOR
-
International Biological Laboratories
The impulse voltage generated in the electric power transmission and distribution system due to lightning or switching phenomena can be simulated by generation of impulse voltage of particular shape in the laboratory.
-
Product
4-Channel, Sigma-Delta ADC Function Card
ProDAQ 3430
-
The ProDAQ 3430 is a 4-channel, sigma-delta ADC function card. Every channel contains front-end conditioning circuitry followed by a sigma-delta ADC. The bit stream from every ADC is then directed to finite impulse response (FIR) decimation filters. Users can activate up to 10 stages of the FIR filters. The filtered data from the selected stages is then stored in the FIFO. The data from the FIFO easily can be moved on-the-fly to the motherboard or to the host.
-
Product
.13u ESD diode
Impulse TSMC
-
The Impulse TSMC .13u ESD diode was made to provide ESD discharge paths when integrating third party IP in an integrated circuit design for total ESD protection. The Impulse ESD diode has been successfully used with Dolphin Technologies, Artisan/ARM, TriCN/Synopsis I/O libraries, as well as popular IP blocks from RAMBUS, Chip Idea and other quality IP vendors. A 5.5 volt reverse bias anode to cathode operational specification enables the Impulse TSMC .13u ESD diode to be the device of choice for 5 volt tolerant designs.
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
Impulse Magnetic Field Immunity Tester
IMF61000-9
-
IMF61000-9 impulse magnetic field immunity tester is high performance test instrument which special designed for to do impulse magnetic field immunity test and fully meet IEC61000-4-9, EN61000-4-9 and GB/T17626.9 standards, also it come with high intelligent, high stable performance and easy operation characteristics.
-
Product
Ocean and River Instruments
RINKO III
-
Rinko III is an analog version with the fast optical DO sensor and a temperature sensor. With an external 12 DCV power, the instrument seamlessly outputs the analog data (0 to 5V) of the sensors. Rinko III can be easily integrated on various platforms with an Impulse cable. By the fast response, the instrument provides high accurate DO data without restricting profile speeds.
-
Product
Pulse generator
9355-1
-
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
Product
Capacitor Tester
MIG0603CAP
-
The MIG0603CAP consists of two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape 1,2/50 µs and are combined in a 4 unit height 19" rack. The generator circuits are defined in IEC 60384-14 and EN 132400. The serial resistors Rs, the impulse capacitor CT, and the load capacitance Cp will be automatically switched when different capacitance ranges are selected on the MIG0603CAP.
-
Product
Impulse Generators
-
Provides pulse widths (measured at the 20% rise timepoint) in the range of 130 ps to 2 ns, amplitudes as high as 100 Volts, with pulse repetition frequencies to 1 MHz.
-
Product
Power Transducer
-
Beijing GFUVE Electronics Co.,Ltd.
Devices capable of transforming or converting a certain type of input energy into another different from the output, they serve to obtain information from physical and chemical environments to obtain electrical signals or impulses and vice versa.
-
Product
Time Domain Reflectometer
IRG 2000
-
Cable fault location with the BAUR IRG 2000. The IRG 2000 impulse reflection measurement unit or time domain reflectometer is a handy, easy to carry device for single-phase cable fault pre-location. It is used in combination with a surge voltage generator on low-, medium- and high-voltage cables 0 - 65 km in length. It can also be used on live cables carrying voltage up to 400 V.* Easy and quick cable fault location* Light, compact and manageable* Main unit for the tried-and-tested pre-location method* Ideal for integration in measurement systems
-
Product
Inductor Tester
-
An impulse can be applied to the coil of a chip power inductor to perform insulation tests (surge tests) within the windings.
