Power Test Systems
-
Product
Versatile quality control testing system
QuickSun® 550Ei
-
QuickSun 550Ei is a versatile testing system for qualifying of PV modules with dimensions up to 105 x 205 cm2. Basic set up includes a top class solar simulator which measures modules in sunny side up position enabling e.g. soiling simulations. Several additional measurement methods can be integrated to the same system including high resolution EL imaging with analysis software from one of the most recognized EL system suppliers. Also hot spot revealing IR images can be recorded by applying either forward or reverse bias current, and true nA scale leakage current measurements can be performed with sensitive enough instruments.
-
Product
Combined Environmental Reliability Test System
VTC SERIES
-
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
Product
Battery Test System
WBCS3000Le32
-
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : -1V to 5Vmax. current range : ±1A
-
Product
Test Automation Platform Deployment System
KS8000A
-
TAP is a modern Microsoft .NET-based application that can be used stand-alone or in combination with higher level test executive software environments. The Keysight KS8000A Test Automation Platform (TAP) Deployment System provides a lower cost, scaled down alternative to the full KS8400A TAP Developers System without the graphical user interface, results viewer and timing analyzer. Deploy your existing test software and TAP plugins into manufacturing environments using the KS8000A command line interface or your own interfaces.
-
Product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
Power Supply
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
Product
Automated Robot Test System
ATS-8000A
-
High Power Pulse Instruments GmbH
The ATS-8000A test system is a fully automated 2-pin probing solution for HBM, TLP, HMM and CC-TLP on package- and wafer-level.Future extension for CDM is optional.
-
Product
Brake Test Systems
Giant 8000 Series
-
Customer perception of vehicle quality is closely related to the NVH behaviour of the vehicle. With the HORIBA ATS Brake testing system, NVH relevant design features are analyzed and various metrics stored in the database of the automation system. For friction borne vehicle NVH problems coming from the brake and its components the GIANT 8000 Series is the ideal tool to resolve it. The GIANT 8000 Series is superior NVH test system providing you with the best testing conditions for all types of vehicles. Test brake fixtures could be tested with a complete wheel suspension system. In a semi acoustic chamber NVH tests could be realized and drum brakes and disc brakes including the vehicle axle could be tested.
-
Product
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps)
7-251914000-072
Power Patchcord
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps).
-
Product
200W Autoranging Power Supply, 60V, 10A
E36232A
Power Supply
E36232A provides more useable power with autoranging architecture in a bench friendly design with full programmability; LAN, USB and optional GPIB interface.
-
Product
SR/QE Testing System
PVE300
-
Industrial Vision Technology Pte Ltd.
Solar Cell Multi-function SR/QE Testing System is specially designed for Photovoltaic Industry to characterize the Optical Performance of Raw material, process wafer, finished solar cell, as well as small Module.
-
Product
Battery Test System
WBCS3000Ls32
-
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : ±5Vmax. current range : ±10mA
-
Product
Test System Elowerk
eloZ1
-
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the latest generation. It reliably finds connection errors and assembly errors in electronic assemblies. The test electronics can be integrated both in table systems and in inline systems.
-
Product
Haptic Testing System
-
The Air Ventilator Haptic Test System performs automatic functional tests on air ventilation components to measure the force necessary for the execution of movements in the different components of the part. The movements are performed by a 6-axis robot that forces the components of the part to follow the desired routes while storing data on the force expended. This particular machine tests movable fins and knurled wheels by performing four test motions on each fin and two on each wheel.
-
Product
Circuit Breaker Endurance Test System
-
Endurance testing involves operating – closing and opening – the circuit breaker repeatedly for a set number of cycles. This test is necessary to stabilize the circuit breaker mechanism and to identify “Early Infant Mortality” failures in the switchgear assembly.
-
Product
Power Performance Test
-
The performance index of power product is decide the product quality, so it is very important to accurately test performance index in every stage to make sure that the product performance is conform to design index. Energy efficiency index includes power factor, input power, input voltage and etc.
-
Product
Systems Integration & Test
-
Watring Technologies, Inc. is an experienced, diversified high technology company proficient in total system integration services including test & evaluation, custom tooling design, and automated hardware validation and verification. We give customers access to a sole- source, multi-disciplinary staff of specialists offering turn-key solutions.
-
Product
Automated Engine Testing System
-
Automated engine test system is intended for comprehensive testing of electrical motors with shaft rotation frequency up to 70 000 rpm. Such engines include:*high-voltage motors;*traction engines;*internal combustion engines;*AC motors;*DC motors;*synchronous engines;*asynchronous engines;*asynchronous engines with short-circuit rotor.
-
Product
High Power Burn-In Test
-
Easily test the reliability of your high power laser devices with the Y2000H burn-in and life-test system. It will quickly identify defective laser devices so you can prevent them reaching your customers. Y2000H's full automation and expandable capacity helps you work through your tests more productively. And its user-friendly software makes testing your devices easier than ever.
-
Product
5000 Watt System Power Supply, 40V, 128A
6684A
Power Supply
Keysight high performance DC power supplies offer speed and accuracy for test optimization. The single output, 5000W, GPIB 6680A-6684A provide low output ripple and noise; selectable compensation for inductive loads; analog control of output voltage and current; and fan-speed control to minimize acoustic noise.
-
Product
Transformer Test System
-
Transformer testing instrument, can be used as a stand-alone device and has the highest efficiency. Can be used in power transformers, network communication transformers, etc.
-
Product
Electric Vehicle Module Test System
FTV
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LBattery Module TestingStart/Stop TestingTraction Battery TestingSupercapacitor / Ultracapacitor TestingDrive Cycle Testing
-
Product
100W Dual Output Power Supply Two 8V, 5A or 20V, 2.5A
E3648A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 90W, multiple output E3648A is a clean, reliable power supply for general purpose applications, and combine convenient benchtop capabilities with flexible system features in a compact, multi-output package.
-
Product
Mixed Signal Test Systems
MTS1020i
-
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
Optics Test Systems
Lens Test
-
Optik Elektronik Gerätetechnik GmbH
LensTest enables the measurement of air gaps, lens thickness, lens radii and lens surface centration errors in mounted lenses as well as the active alignment of lens surfaces during optics assembly for centering without rotating the assembly.
-
Product
Standalone Test System
1000 Series ATE
-
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
Product
NI Real-Time Test Cell Reference System
780590-35
test
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
Product
Regenerative Power System, 500 V, 40 A, 10 kW, 200/208 VAC
RP7952A
DC Power Supply
The RP7952A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
Product
EMI and EMC Test System
-
EMI receiver system. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KB is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem.
-
Product
Analog IC test system
-
A paradigm shift has been occurred in Japan’s major brand WL25 series tester. Ultimate simple system is available by effective analog pin architecture.This cost performance system is covered analog IC extensively, which are high accuracy, speed and multi-site test function.
-
Product
IC Testing System
-
Is a system for giving electrical signals to a semiconductor device to compare output signals against expected values for the purpose of testing if the device works as specified in its design specifications.
