Product

Low Noise Pre-Amplifiers

-

Praxsym

Praxsym

Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.

Product

Ultra Low Noise Disciplined Frequency 4220a Standard with Rubidium and OCXO Clean-Up Oscillator

-

Precise Time and Frequency, Inc.

Precise Time and Frequency, Inc.

The ptf 4220A is an Ultra Low Noise Disciplined Frequency Standard with rubidium and OCXO clean-up oscillator.The instrument contains a high performance rubidium module, with an extended life design, and very low aging rate, with high quality OCXO o/p for low phase noise.

Product

Millimeter-Wave Noise Source, Q-band, 33 To 50 GHz

Q347B

-

Keysight Technologies

Q347B - Keysight Technologies

The Q347B waveguide noise source (33 to 50 GHz frequency range), allows you to make accurate noise figure measurements on millimeter-wave devices...

Product

Low Noise Amplifier (DC Powered)

-

RF-LAMBDA Inc.

RF-LAMBDA Inc.

RF Lambda’s DC low noise amplifiers (LNA) are broadband and offer low noise figure high IP3. Hermetically sealed options are available upon request.

Product

High Density, Low Noise, Floating Low Voltage Power Supply System

PL500 Series

-

W-IE-NE-R, Plein & Baus GmbH

PL500 Series - W-IE-NE-R, Plein & Baus GmbH

The WIENER PL500 is a high density, low noise, floating low voltage power supply system. The PL500-Series has been designed  to power lowest noise electronics with medium to high currents (10A to 500A current/channel range) over long distances in voltage or current controlled mode. Operating in either un-sensed or sensed mode the dynamic behavior can be set internally or by software for short, medium or long distances.

Product

Low Noise Amplifiers

-

Micran Co. Ltd.

Micran Co. Ltd.

Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).

Product

Noise Monitoring Kit

LxT NMS SoundExpert

-

Larson Davis, Inc.

LxT NMS SoundExpert - Larson Davis, Inc.

In addition to the SoundExpert LxT meter, this kit includes the EPS042 protection case and D-cell battery pack, the EPS2116 microphone protection shroud, and EXC010 10 ft. cable. Using D-cell alkaline batteries, allows the noise monitor to be smaller and lighter; avoid the expense of shipping heavy lead acid batteries and the hassle of recharging. You can transport it easily to your site, deploy it, measure data, retrieve your system, download the data, and issue your report.

Product

Low Noise AC Amplifiers

-

Millivac Instruments

Millivac Instruments

Your product description goes here.

Product

Noise & Vibration Measurement Systems

BK8600

-

BaKo Co., Ltd

BK8600 - BaKo Co., Ltd

Rotation can produce noise and extraneous vibration for any number of reasons and could cause wear, discomfort, or other problems. The BK8600 series of testers are specially designed to test for these.

Product

Ultra-low Noise High Voltage Amplifier

WMA-200

-

Falco Systems

WMA-200 - Falco Systems

The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.

Product

1/2.5" 5.0 MP Low Noise USB Camera (Color)

See3CAM_CU55

-

e-con Systems Inc.

See3CAM_CU55 - e-con Systems Inc.

See3CAM_CU55 is a 5.0MP USB3.1 Gen1 UVC Color Camera with S-mount (also known as M12 board lens) lens holder. It is a two-board solution containing camera sensor board based on 1/2.5" AR0521 image sensor from ON Semiconductor and USB3.1 Gen 1 Interface board. The powerful on-board Image Signal Processor (ISP) brings out the best image quality of this 2.2micron pixel 5MP AR0521 CMOS image sensor making it ideal for next generation of high resolution surveillance, biomedical instruments and biometric authentication applications.

Product

Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz

R347B

-

Keysight Technologies

R347B - Keysight Technologies

The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.

Product

Low Noise Amplifiers

-

Skylink Microwave

Skylink Microwave

LNA is an outstanding and mature product line of Skylink Microwave. We provide high performance low noise amplifiers in the industry, with reliable and rugged quality. Ultra low noise, ultra broadband and compact size are our specialty and enduring pursuit. Our engineers are committed to satisfying higher custom requirements of our customers and insist on designing optimized products to meet market challenges. Skylink Microwave provides you an extensive line of low noise amplifiers and the most economical choices.

Product

Low Noise Accelerometer Cables & Coaxial Sensor Cables

-

Kemo

Kemo

Our cable assembly team in the UK produce the highest quality cable assemblies for use with a wide range of sensing and measurement applications. By making the cable assemblies in our own factory we are able to ensure the quality of every connection and every assembly, each cable is fully tested and its capacitance checked. Due to our experience in signal conditioning we understand the critical elements to quality signal analysis, this includes the correct cable. This is particularly true for accelerometer cables and sensors cables which can introduce significant noise issues if not used correctly.

Product

Low Noise Amplifier

-

ERAVANT

ERAVANT

Low noise amplifiers, or LNAs, are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a low noise performance with broad operating bandwidths and good gain flatness. While standard models focus on general purpose applications, additional models with differing frequency ranges, gains and noise figures are listed on the website. Custom designs are also offered to meet any user’s specific needs.

Product

Noise Board

332D-11 VG

-

Tech-Aid Products

332D-11 VG - Tech-Aid Products

This printed circuit board was designed to original specifications and contains OEM specified parts. This board is required for testing the 332D-11 series gyros. Also contained on board is the Method A type calibration and sample and hold circuits required to perform the calibration of the noise circuits.

Product

Low Noise Dual Band VCO

-

Teledyne RF & Microwave

Teledyne RF & Microwave

This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.

Product

Antenna Noise Canceller

ANC-4

-

Timewave Technology Inc.

ANC-4 - Timewave Technology Inc.

The ANC-4 is an rf device that eliminates or reduces power line noise, BPL noise, computer noise, TV-generated interference, and other types of electrical noise. The ANC-4 unit connects right to the antenna connector of the receiver or transceiver to cancel locally generated noise before it gets into the receiver and affects the receiver AGC circuits.

Product

Phase Noise Testing

-

Precision Test Systems Ltd.

Precision Test Systems Ltd.

The systems are based in the UK although testing for any company world wide will be undertaken.

Product

Phase Noise Measurement Solutions

-

Keysight Technologies

Keysight Technologies

Keysight offers dedicated phase noise measurement solutions to simplify your measurements and maximize your efficiency. Building on 30 years of low phase noise and RF design and measurement experience, our innovative solutions are designed to provide the most accurate phase noise data possible, and are economically tailored to fit your specific performance and application needs - now and well into the future.

Product

Low Phase Noise Amplifier

-

RF-LAMBDA Inc.

RF-LAMBDA Inc.

RF Lambda’s lower phase noise amplifier offerings include special power supply conditioning and utilize technology to reduce the phase noise addition from amplifying the signal. Hermetically sealed options are available upon request.

Product

Phase Noise Tester 5MHz to 40GHz

Model 7340

-

Berkeley Nucleonics Corporation

Model 7340 - Berkeley Nucleonics Corporation

Broad Frequency Range in a single compact instrument from 5MHz to 40GHz. Measurement offsets from .01Hz to 100MHz. Absolute Phase Noise - High Drift mode (ability to measure modulations, high drifting or unstable DUTs, etc.). AM (Absolute Amplitude Noise) measurements. Pulsed Measurement Capabilities. Transient Mode: measure WB Frequency, NB Frequency, NB Phase, NB Power (WB/NB being Wide Band and Narrow Band). Dual channel low-noise integrated power supplies.