Automation
-
Product
Digital Automated Fiber & Ferrule Interferometer For Single Fiber Connectors
DAFFI SF
-
The latest interferometer from Data-Pixel is a cost effective solution for high volumes production, without compromising on accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI SF to be robust, fast and accurate in order to meet all manufacturing or laboratory environments. With the Blink software platform, DAFFI is able to measure the end face geometry on single fiber connectors in a very short time. The Daffi interferometer accessories (flange and adapters) are fully compatible with the Daisi range, allowing the user to limit the costs of the 3D geometry measurement units.
-
Product
Data Acquisition
-
Data Acquisition used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems.
-
Product
PCI-6225, 80 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device
779295-01
Multifunction I/O
80 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device - The PCI‑6225 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
On-line ICP / ICP-MS Sample Preparation System
SDX ʜᴘʟᴅ
-
The SDXHPLD system combines the proven ASX‑560 autosampler with a novel vortex mixing dilution accessory. The system dilutes in the same way you do by hand: volume-to-volume dilution, using a highly accurate syringe pump. But it also goes an additional step to vortex mix the resulting dilution prior to sample introduction to ICP and ICP-MS.The SDX employs vortex mixing to promote homogenization of a sample to ensure accurate and precise analysis following dilution. The variety of sample matrices submitted for trace element analysis necessitates the need for mixing. This long overdue capability improves data quality by fully homogenizing a dilution mixture rather than performing in-line combination.The SDXHPLD is a straight-forward, fully-integrated solution for automated dilution of aqueous and acid base sample prep for ICP or ICP-MS.
-
Product
Linear And Gantry Robots
-
Linear robots, whether gantry robots or other Cartesian designs, can deliver precise, smooth motion and excellent load-bearing capabilities required by advanced automation systems. With configurations ranging from single- to multi-axis, linear robots offer a design flexibility that can address a wide range of automation tasks — from long-travel transfer robots to small precision motion stages. In many cases, linear robots can even replace multiple six-axis articulated arm robots, reducing the total cost, footprint and deployment time for automation systems.
-
Product
Consultancy Services
-
CellCare Technologies are experts in all types of standby battery servicing, specialising in automated monitoring, data acquisition systems, on-site battery management and maintenance, together with fault diagnosis and performance prediction. Our services also include product application and consultancy, plus training seminars on standby battery maintenance. Health & Safety courses to ensure compliance with COSHH regulations are also available.
-
Product
Software For Measuring Process Automation
NMS AutomationSoft
-
A software tool made by NMS, intended especially for users of measuring systems. It allows simple and fast creation of measuring programs – complete work procedures, from the choice of measured part and navigation through the entire measurement to automatic data evaluation and the creation of reports. The program allows the use of dialogues and images that simplify orientation in the measurement process for operation
-
Product
Web Application Testing
-
We provide manual, semi-automated and automated functional testing services to ensure that both front-end and back-end components of the application work properly and as initially designed.
-
Product
Automated Testing
TestComplete
-
Got an aggressive testing schedule? No problem. With this automated testing tool, designed for advanced and novice testers alike, you can create, manage and run tests for any desktop, Web or rich client software. Revel in the easy-to-use interface and script-free testing combined with a powerful set of customization features.
-
Product
HART Protocol Stack
softHART
-
SoftHART is the industry-standard smart HART (Highway Addressable Remote Transducer Protocol) communications stack for industrial automation. HART is a bidirectional protocol and communicates over existing 4-20 mA analog current loops, extending communication capabilities without the inconvenience of installing additional wiring.
-
Product
LAN⇔RS-422/RS-485 Conversion
SI-65
-
SI-65 is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
Product
WaferPro Express On-Wafer Measurement Program Software
-
WaferPro Express software performs automated wafer-level measurements of semiconductor devices such as transistors and circuit components. It provides turnkey drivers and test routines for a variety of instruments and wafer probers. Its new user interface makes it easy to setup and run complex wafer-level test plans, while powerful customization capabilities are enabled by the new Python programming environment.
-
Product
Spinstand Automation For Media Testing With XY-Positioning
V2002
-
Guzik V2002 XY-positioning spinstand uses the X and Y coarse positioning stages actuated by linear motors and the micro-positioning stage actuated by the piezo element aligned with X coordinate axis to place the tested head on the specified track. WITE32 software converts the requested track number and skew angle into X and Y coordinates.
-
Product
Testing solutions
-
From Manual Testing, to test automation Ideabytes Inc is a one stop shop for all testing needs. Among the specialities Model Based Testing that changes the approach to testing reducing cost and catching faults early. With our methodologies, automated test cases are ready just as the developers are releasing their code. Contact us for a free consultation!
-
Product
Dual-Sensor Temperature-Measurement Pan/Tilt
TRITON™ A310 PT (Security)
-
Security professionals around the world have been using FLIR thermal cameras for perimeter and critical asset security for years. Facility Operations and Safety personnel have been using FLIR cameras to gather non-contact temperature measurements and condition monitoring data for decades. A310F and A310PT cameras are the first in the world to combine thermal and visible light video security imaging with automated safety monitoring based on the detection of temperature measurement thresholds.
-
Product
PCIe-6351, PCI Express, 16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO Multifunction I/O Device
781048-01
Multifunction I/O
PCI Express, 16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO Multifunction I/O Device - The PCIe‑6351 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6351 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Mixed Signal Battery Test System
Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
Product
XRD
-
Anton Paar’s precise and flexible XRD solutions combine the best possible data quality with unrivalled measurement efficiency. Our reliable systems are designed for intuitive use and offer a high degree of automation so every user can benefit from increased sample throughput and maximum instrument uptime. The XRDynamic 500 powder diffractometer features advanced optics, a next-generation goniometer, and state-of-the art detectors with a wide range of applications covered by the extensive ambient and non-ambient sample stage portfolio so you can always find the optimal XRD system for your needs.
-
Product
19" Subracks
-
Elma implements quickly and easily scalable, robust 19'' subracks, card cages or rackmount chassis for the use in just about any industry or environment: Industrial automation, test & measurement, transportation, energy, defense, communications and medical. The products of Elma Electronic support standards such as IEC, IEEE or AdvancedTCA.
-
Product
Macro Inspection
-
High-throughput automated macro inspectionAny wafer size, in less than one second with ~75 micron resolutionSmall footprint table-top system
-
Product
Precision Energy Meter
WattsOn – Mark II
-
Ideal for Energy Management, Solar, Export Limit, Building Automation and OEM Applications. The WattsOn-Mark II Precision Energy Meter uses cutting-edge metering technology to provide unprecedented accuracy, resolution and metering performance for any electrical installation. WattsOn monitors each phase individually and incorporates the functions of single-phase, split-phase, and three-phase meters.
-
Product
MSN Sniffer 2
-
MSN Sniffer is world's first sniffer to automate MSN chat capturing and impact analysis. After installed on one computer, it captures MSN chat across all computers in the same LAN, analyze and save into database for future analysis.
-
Product
3D Automated Optical Inspection Systems (3D-AOI)
3Di Series
-
Saki’s 3Di Series applies cutting edge technologies to improve production efficiency and enhance production quality across the entire assembly line.
-
Product
Game Testing
-
Testing mobile game means ensuring that it is running properly, it meets its all specific requirements and provides fantastic user experiences to gamers. This may sound difficult – especially when there are bazillion different device configurations where the game must run well. If you consider that significant portion of Google Play and App Store revenues are generated by mobile games, there is absolute need to automate as many mobile game components as possible.
-
Product
Meter Test Board
WECO 2150
-
Model 2150 automated test system is a fully ANSI compliant testboard that uses a single voltage and three independently controlled isolated current sources to test all electromechanical and solid state meters up to 50 Amps. Utilizing a precision laser optics system, the Model 2150 can test meters through the most grime-coated covers with unfailing accuracy. This same laser technology makes it possible to test using the disk’s edge without wasting time with the tricky optics adjustments found with other test systems.
-
Product
Automation
ZETLAB Formula
-
ZETLAB Formula is a program used for mathematical operations with signals, signal filtration, and parameters measurements, producing signals with various shapes. ZETLAB Formula is a virtual measuring tool allowing to perform arithmetical and logical operations and filtration of constant data flows received from ADC and DAC modules and virtual channels in real-time mode. In the post-processing mode, it is possible to perform various operations with the files created by means of “Signals recording” program.
-
Product
Traffic Photo Enforcement
LidarCam 2
-
Automatically collect a video + multiple high-resolution photos every time you capture a traffic violation. Built-in Automated License Plate Recognition (ANPR/ALPR) Technology can automatically check for wanted plates or other violations. Hand-held or mounted to a tripod, in a patrol vehicle or from the side of the road, the Stalker LidarCam 2 is the next generation of photo enforcement.
-
Product
PCIe-6321, PCI Express, 16 AI (16-Bit, 250 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device
781044-01
Multifunction I/O
PCI Express, 16 AI (16-Bit, 250 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device - The PCIe‑6321 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6321 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
HDC Torque Controllers
-
The HDC controllers operates with only the HD-Series automation electric screwdrivers. It is a single tool controller that offers programmable speed, angle, auto reverse and soft start options. The controller provides programmable fastening options for sequence based assembly automation applications. The patented HD-Series hybrid system is the world's first torque control tool using both air and electric power to set and control torque. The HDC precise pneumatic pressure sensor and patented algorithm allow for precision digital torque selection.
-
Product
TIM Tester
-
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
