Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Flexible 32-bit PCI to x1 PCI Express Adapter
SKU-049-0X
The Flexible 32-bit PCI to x1 PCI Express Adapter (Adapter) was designed to expand the 32-bit PCI bus into an x1 PCI Express bus. It allows you to connect the x1 PCI Express expansion board to the motherboard PCI connectorThe Adapter includes an x1 PCI Express adapter board, 32-bit PCI host board and PCI Express Flat cable.
-
product
PCI Adapter for cPCI
PCI2cPCI
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
PCI to PC/104+ Bus Adapter
327/328
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
product
CompactPCI
cPCI4IP
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
product
DG I/O Backplane Extender Board
9286-1015
15" x 15" Backplane Adapter. Not to be used in production environment. Used with any I/O bus adapter during installation of Hawk system. Presents Nova/Eclipse bus signals on dual 50-pin connectors. Two 10 ft. (3 m) ribbon cables included.
-
product
Programmable Power Modules
Series MST
MST power modules are a group of programmable power supplies that are compatible with Kepco¹s single address, multiple instrument serial control bus. The MST provide precision interactive control in the 200 Watt power class. The housings for MST, either RA 55 or CA400, each contain a slot to accommodate an IEEE 488.2 adapter. If not used, an additional MST power module may be plugged into that slot.
-
product
Rugged Ethernet
ES-1553RUNET/Px(S)
The ES-1553RUNET/Px is an intelligent, rugged single channel, MIL-STD-1553 adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in rugged environments.The ES-1553RUNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
product
PCI to PCI Express Adapter
SKU-011-01
The PCI to PCI Express Adapter simply turns your computer’s existing PCI slot into a PCI Express slot. This provides a seamless interface for older PCI systems to accept new PCI Express devices – making it possible to utilize old test equipment (computers, PCI extenders, PCI bus analyzers etc.) during migration from PCI to the PCI Express interface.There is no need to purchase additional software or to install new device drivers; simply plug & play!
-
product
SAS (Serial Attached SCSI)
Serial Attached SCSI (SAS) is a data transfer technology designed to move data to and from storage devices such as disk drives, host bus adapters (HBA), and expanders. SAS is a serialized enhancement and replacement to parallel SCSI. Since SAS ratification in 2004, and it’s move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with it’s industry leading protocol analysis and traffic generation capabilities.
-
product
LXI WTB Adaptor, Thru line
60-982-001
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
Flexible MiniPCI Express Riser
SKU-055-0X
The Flexible MiniPCI Express Riser (Riser) was designed to extend the MiniPCI Express bus. The Riser includes a MiniPCI Express adapter board (downstream), MiniPCI Express host board and a 12” PCI Express flat cable.The MiniPCI Express host board connects to the motherboard MiniPCI Express connector.
-
product
Hawk EI Co-Processor
9322 EI
Hawk Co-Processor (Hawk-E) including I/O bus adapter with control logic for DG-compatible I/O devices, two slots required. Supports both Programmed and Data Channel I/O.
-
product
Tiny Can
Our experience in the CAN bus area is evident in our Tiny CAN product range. Starting with our robust and inexpensive hardware adapters to the cross-platform Tiny-CAN-API to the monitoring tool Tiny-CAN-Monitor - both beginners and professionals will find a variety of solutions for the development of CAN bus systems.
-
product
Kestrel /SX Co-Processor
0149-SX
Same speed Windows/NT Kestrel Co-Processor for equivalent system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the HP1000 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes compatible hardware floating point. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. HP1000 Bus support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel adapter. Operates only under Windows/NT. WNT Support license included.
-
product
I2C Bus Host Adapters
iPort/AFM 2 brings I2C directly to your Windows, Linux, or Mac OSX PC, Single-board Computers, or Embedded Systems. Just load our free software, plug the iPort/AFM 2 into your computer's legacy or add-on RS-232 port, and you will be sending and receiving I2C Bus messages in minutes.
-
product
3U CPCI To PCI 4 Slot Adapter
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
product
FantASI ASI/SD-SDI Input+output For USB-2
DTU-245
DekTec's classic and iconic portable ASI adapter for USB bus, ideally suited for use with a laptop, but convenient with a standard PC or server too. More than ten years on the market and still the essential tool for every DTV engineer!
-
product
Flexible 32-bit PCI to MiniPCI Express Adapter
SKU-057-0X
The Flexible 32-bit PCI to MiniPCI Express Adapter (Adapter) was designed to convert the 32-bit PCI bus into a MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion board to the motherboard PCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), 32-bit PCI host board and PCI Express flat cable.
-
product
Osprey ISA Q-Bus Adapter board
9476-Q-B
Qbus Controller board for Osprey ISA/EISA bus compatible. Occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
product
GPIB to Quad Serial Interface
Model 4896
* Provides four RS-232/RS-422/RS-485 Serial Channels.* High speed, 115.2 K baud channels include 60 K byte buffers.* > 600 K byte/sec. GPIB data transfer rate.* SCPI commands set serial configuration and GPIB address.* LCD display shows Bus activity, buffer status, serial interface signals and channel settings.* 1 U high rack mount kit mounts one or two 4896s * Includes US 115 VAC Power Adapter, Manual and Support CD.
-
product
Flexible x1 PCI Express to MiniPCI Adapter
SKU-067-0X
Flexible x1 PCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert PCI Express bus into standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard PCI Express connector.Adapter includes a MiniPCI Adapter board (downstream), x1 PCI Express host board and flat PCI Express cable.
-
product
Compact PCI
cPCI2IP
The cPCI [Compact PCI] compatible cPCI2IP design adds 2 Industrypack compatible slots to your cPCI host. The cPCI2IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI2IP is a 3U 4HP cPCI design with 2 IP slots.
-
product
LXI WTB Adaptor, Terminated
60-982-002
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
Flexible 32-bit PCI Riser
SKU-050-0X
The Flexible 32-bit PCI Riser (Riser) was designed to expand the 32-bit PCI bus into 2 32-bit PCI buses. The Riser includes a PCI adapter (downstream), 32-bit PCI host board and PCI Express Flat cable.The PCI adapter has 2 32-bit PCI slots for plugging in two 32-bit PCI add-in boards. The PCI host board connects to the motherboard PCI connector. The PCI Express Flat cable (12 inches) is used for connecting the host board with the PCI backplane, and it provides a flexible connection between the 32-bit PCI add-in boards and the motherboard.
-
product
Standalone Bench Test System for FCT, ICT, ISP and Boundary Scan
LEON Bench
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable Test Adapter) frame allows various fixture houses all over the world to build custom fixtures for the LEONBench. Up to 15U additional rack space allows adding a bunch of high-performance measurement devices from various manufactures. An integrated power distribution unit takes care about power on and off sequencing.As part of the LEON Family, LEONBench is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
product
Flexible x1 PCI Express to MiniPCI Express Adapter
SKU-056-02
The Flexible x1 PCI Express to MiniPCI Express Adapter (Adapter) was designed to convert the x1 PCI Express bus into the MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion add-in board to the motherboard PCI Express connector.The Adapter includes a MiniPCI Express adapter board (downstream), x1 PCI Express host board and PCI Express flat cable.
-
product
Intelligent, Single- or Dual-Channel MIL-STD-1760 Adapter
EXC-1553UNET/Px-1760
The EXC-1553UNET/Px-1760 is an intelligent, single- or dual-channel, MIL-STD-1760 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1760 bus, both in the lab and in the field.The EXC-1553UNET/Px-1760 shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.In addition the EXC-1553UNET/Px(S)-1760 provides 8 I/O Discrete signals and an IRIG B input.
-
product
PCI to PMC Adapter/Carrier
PCI2PMC
The PCI2PMC ( PCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI slot. The PCI2PMC has a PMC card slot mounted to a universal 1/2 length PCI card. Suitable for 32 bit or 64 bit data with 33 or 66 MHz bus operation. The PMC user IO connector Pn4 is brought out to two connectors for access (DIN IDC and SCSI II compatible).
-
product
Networked Absolute Inclinometer
T7
The T7 is available in several interface and protocol options. The physical interface can be RS232, RS485 or US Digital's CAN (Controller Area Network). The protocol can be either US Digital's serial protocol or Modbus RTU. The RS232 version supports a single T7 with up to 100 ft of cable. For users that need longer cable lengths or multiple T7s on a single bus, the RS485 or US Digital CAN (Controller Area Network) version can be used. The USD-CAN protocol allows a network of up to sixty-four T7s to be connected to a single host. Power for each T7 is supplied over the CAN network cable. The host accesses the USD-CAN T7s through US Digital's low cost CANA-232/CANA-485 adapter module. This module allows the host to access each T7 on the network using simple, easy serial port commands, just like the RS232 version. The RS485 version supports up to 32 T7s on the bus.
-
product
PCI-104 Adapter for PMC
PC104p2PMC
PC104p2PMC ( PCI-104 to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI-104 slot. Suitable for PCI operation with 32 bit data and 33 or 66 MHz bus operation.
