Protection Relay Test
-
Product
PXI Dual Microwave SPDT Relay 26.5GHz 50 SMA
40-780A-532
-
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
PXI/PXIe Power Relay Module, 32xSPDT, 5 Amp, 50-Pin SGMC Connectors
42-158-001
-
The 40/42-158-001 is a PXI/PXIe high density power relay module with 32xSPDT switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 67 GHz, 50 Ω, SMA-1.85, Failsafe
42-780B-572
-
The 40-780B-572 (PXI) and 42-780B-572 (PXIe) are dual failsafe SPDT 67 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI Dual Microwave SPDT Relay 18GHz 50 SMA
40-780A-522
-
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
PCI Reed Relay Card, 32xSPDT
50-110B-021
-
The 50-110B-021 is a 32xSPDT PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
Test System for High Volume Production Testing of Integrated Circuits
ETS-364
-
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
PXI 12 x DPST Power Relay Module, 5A
40-151-002
-
40-150/151 modules have 8xDPST or 12xDPST power relays, suitable for switching inductive/capacitive loads up to 5A at 250VAC. 40-155/156 modules have 8xSPDT or 16xSPDT power relays and 40-157 is configured as 8xDPDT.
-
Product
PCI Express 5.0 Test Platform
-
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 40 GHz, 50 Ω, SMA-2.9, Failsafe
42-780B-542
-
The 40-780B-542 (PXI) and 42-780B-542 (PXIe) are dual failsafe SPDT 40 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe Relay Driver Module, 64-Channel, 5V Relay Supply
40-411A-001
-
The 40-411A-001 (PXI) and 42-411A-001 (PXIe) are 64-channel relay drivers and are part of a range of modules with 16, 32, 48 or 64 channels of low side current drive. To use the module, simply connect a positive voltage source to one side of the relay coil and the other side to an output channel. Each output is capable of sinking up to 1 A of continuous current.
-
Product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 37-Pin D-type Connector
40-158-104
-
The 40/42-158-104 is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A. User connection is via a 37-pin D-type male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin D-type Connector
42-158-103
-
The 40/42-158-103 is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A. User connection is via a 50-pin D-type male connector.
-
Product
PXI 12 x DPST Reed Relay 2.5 Amp
40-136-012
-
The 40-136-012 12xDPST reed relay module is part of our range of medium power, general purpose relay modules which are capable of switching voltages up to 200V and current up to 2.5A.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 50Ω, SMB
40-870A-003
-
The 40-870A-003 (PXI) and 42-870A-003 (PXIe) are 50Ω RF switches with 3 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI-2520, 80-Channel, 2 A, SPST PXI Relay Module
778572-20
-
80-Channel, 2 A, SPST PXI Relay Module—The PXI‑2520 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2520 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
Product
Memory Test System
T5230
-
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131C
-
The Keysight 85131C is an 81 cm (32 in) long1 semi-rigid cable with a 3.5 mm female2-to-PSC-3.5 mm female connector. Cable frequency range is DC to 26.5 GHz with a return loss of 17 dB or better. Insertion loss is 0.43 * sqrt(f) + 0.3, where f is frequency in gigahertz, for the test port connector and 2.5 dB at maximum frequency for the device connector. Phase stability of the semi-rigid / flexible cables is specified with a 90-degree bend using a 4 to 3-inch radius. Stability1 of the 85131C is less than 0.06 dB, and phase is 0.16 * f + 0.5, where f is frequency in gigahertz.
-
Product
Conformance Test System
TS8980
-
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
Product
SWB-2815, 4x86, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-15
-
4x86, 0.3 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
-
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
-
-
Product
Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N
85130C
-
The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.
-
Product
PXI-2559, 2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module
778572-59
-
2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module - The PXI‑2559 is a general-purpose switch module featuring two independently terminated single‑pole double‑throw (SPDT) relays. You can use it to add flexibility to your video switch network or to maintain uniform signal paths across multiple channels when building high-channel-count multiplexers. The PXI‑2559 termination resistors minimize reflections on open channels and protect your source or device under test from damage. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 18GHz, 50Ω, SMA, Remote Mount
40-780B-521-E
-
The 40-780B-521-E (PXI) and 42-780B-521-E (PXIe) are single SPDT 18GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
PXI Microwave Relay, Dual SPDT, 2.5GHz, 75Ω, 1.6/5.6
40-780B-752
-
The 40-780B-752 (PXI) and 42-780B-752 (PXIe) are dual SPDT 2.5GHz 75Ω unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions.
-
Product
NI-9485, 8-Channel, SSR Relay, 60 VDC/30 Vrms, 750 mA C Series Relay Output Module
779600-02
-
The NI-9485 allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to a solid state relay (SSR) for switching voltages up to 60 VDC/30 Vrms with switching current up to 750 mA per channel or up to 1.2 A on four channels. Each channel also features channel-to-channel isolation.
-
Product
6TL19 Off-Line Base Test Platform
H71001900
-
The 6TL19 is a bare half-rack with castors for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 11U (580mm depth).
-
Product
PCI 16xSPST 2Amp Relay Card
50-132-001
-
The 50-132-001 16xSPST relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 40 GHz, 50 Ω, SMA-2.9, External Termination, Failsafe
42-781A-522
-
The 40-781A-522 (PXI) and 42-781A-522 (PXIe) are dual failsafe SPDT 40 GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
