Serial Peripheral Interface
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, SMBus
-
Product
1553 EBR to Ethernet Converter
ENET-1553-EBR
Ethernet Interface
ENET-1553-EBR-1D™ is an innovative product that provides “remoting” of 1553 AS5652 EBR operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). ENET-1553-EBR is a small, low-power, rugged device that provides connectivity for up to eight AS5652 RT devices, single BC or composite monitor.
-
Product
LIN Interface Module
C Series LIN
LIN Interface
C Series LIN Interface Modules are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. C Series LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
PCI Mezzanine Card
PNIC1G
Ethernet Interface
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
-
Product
3U CompactPCI 5-Port Serial Ethernet, Optional POE Card
cPCI-A3ETH
Ethernet Interface
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP- 5x RJ-45 ports support up to 2.5G via Intel® i226IT Ethernet controllers- Optional PoE supported- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
8-Ports Gigabit Ethernet RCV Interface (R)
YAV90058
Ethernet Interface
8x RJ45 LAN connectors to VPC RCV 192 pins module.
-
Product
C Series PROFINET Interface Module
Interface Module
The C Series PROFINET Interface Module provides two PROFINET interface ports that enable you to reliably connect programmable logic controllers (PLCs), I/O, sensors, and drives over long distances in industrial environments. PROFINET is an application protocol that uses familiar concepts from PROFIBUS that are implemented on the physical layer of Ethernet. The C Series PROFINET Interface Module includes NI-PROFINET driver software for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces.
-
Product
2U, 4U, and 6U Developmental RF Interface Units
1257A-D
Interface
The Astronics 1257A-D is a sixth-generation RFIU design. It comes with a new easy-to-use LXI Core 2011-compliant device and new enhanced features, including the ability to acquire all of the components you need to assemble your own unit in-house, reducing your design time.
-
Product
Interface
RAR-PXI
Interface
Available in a range of configurations to match your needs, the RAR-PXI provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected two-wire, 32-bit protocols in a PXI compatible CompactPCI form factor.
-
Product
NI-9853, 2-Port, High-Speed C Series CAN Interface Module
779429-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
PXIe-8431/16, 16-Port, RS485/RS422 PXI Serial Interface Module
781473-02
Serial Interface
The PXIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Mini PCI Express
MPCIE-A429
Interface Card
Alta Data Technologies’ MPCIE-A429 Mini PCI Express F1 interface module offers a variety of ARINC-429/575/717 channel configurations with software selectable RX/TX channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 transceiver compatible signal.
-
Product
9-Pin DB-9 Female to 9-Pin DB-9 Female Serial Cable
183283-02
Serial Cable
The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
Product
PCIe-8431, PCI Express, 16-Port, RS485/RS422 Serial Interface Device
780592-02
Serial Interface
The PCIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
3U OpenVPX Sensor Interface Unit
SIU32S
Sensor Interface Unit
The SIU32S is a highly configurable Modular Open Systems Approach (MOSA) rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, processing, communications and Ethernet switching. The SIU32S leverages NAI’s Configurable Open Systems Architecture™ (COSA®) 3U boards and smart function modules to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785324-01
Interface
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PXI-8512, 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-02
CAN Interface
2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
ARINC 429 Interface
RCEI-715A
Interface
The RCEI-715A is an intelligent, high-density, Type II PC Card (PCMCIA) interface that provides up to 12 fully independent ARINC 429/575 channels, along with up to 4 bi-directional avionics-level I/O discretes.
-
Product
Digital/Pattern/PE Card
PEMU32
Interface Card
The PEMU32 represents a new level of MULTIFUNCTION for PXI-based instrumentation. Based on the proven architecture of the PE32, the PEMU32 offers high voltage PMU/DPS and pin electronics in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PEMU32 also supports deep pattern memory by offering 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 10 MHz.
-
Product
3 Function Slot MOSA Nano Aircraft Interface Computer (AIC)
NIU3A-AIC-01
Aircraft Interface Computer
NIU3A-AIC-01 is a Modular Open Systems Approach (MOSA) Aircraft Interface Computer with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
Product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
Ethernet Interface
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, which allows it to synchronize with an external network as well as the rest of a PXI system. The PXIe-8521 also provides LEDs on the front panel so that you can monitor the network link and activity.
-
Product
USB-8501, 2-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786307-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
C Series Serial Interface Module
Interface Module
The C Series Serial Interface Module adds RS232 or RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the field-programmable gate array (FPGA) to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The C Series Serial Interface Module supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. You can choose from both enclosed and non-enclosed modules.
-
Product
Multi-Channel Interface Module
PC104P-MA4
Interface Module
Alta Data Technologies’ PC104P-MA interface module is a multi-channel, multi-protocol 1553 and ARINC PC104-Plus interface card supported by the latest software technologies. The PC104P-MA4 card is based in the industry’s most advanced 32-bit protocol engine, AltaCore, and by a feature rich application programming interface, AltaAPI, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. The hardware and software package provides increased performance and reduces intergration time.
-
Product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
Interface Card
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
Product
Network Interface Card
NIC10GBT
Interface Card
The NIC10GBT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
Peripherals & Interface Cards
-
Interface cards are plug-in modules that provide interfaces for control/communication of/with external components or test items.The modules themselves are controlled via standard interfaces such as USB 2.0/3.0, PCI, PCIe, PXI, PXIe or LAN.
-
Product
Interface
RQVME2-1553
Interface
The RQVME2-1553 provides new levels of performance and flexibility for MIL-STD-1553A and B Notice II on the VMEbus. Available in commercial, industrial and conductively cooled versions with one, two or four dual-redundant channels, the RQVME2-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
Interface
RCEI-830A
Interface
Designed for embedded, laboratory and simulator applications, the RCEI-830A supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, receive message time-tagging and error detection, and IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL).
