Filter Results By:
Products
Applications
Manufacturers
CAT 6
Category 6 cable.
- Pickering Interfaces Inc.
product
PXI 8 Slot BRIC 90x16 2-pole (6 sub-cards)
40-561A-122-90X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Network Toner & Probe Kit
MT-7028
The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
product
Infrared Motion Sensor
ENVIROMUX-IMD
Registers movement in the area covered. Condition display via LED. Provides immunity from common-mode signals such as the effect of strong hot or cold air currents, variation in ambient temperature, background radiation and acoustic noise. 24 dual-element detection zones for long, mid and short range protections. Surface or corner mounting. Pulse count or single shot triggering. Good RFI protection. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Includes mounting bracket for installing the sensor to a ceiling or wall. Regulatory approvals: CE, RoHS.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co. KG
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
Banana Adapters
Pasternack Enterprises Banana adapters category has 6 part numbers, the majority are RoHS and REACH compliant. impedance Banana adapters are part of a complete adapter product line from Pasternack.
-
product
Network Cable Continuity Tester
T014-001
The all-in-one T014-001 Network Cable Continuity Tester is an essential tool for cable installers or anyone working in telecom or LAN environments. It allows you to test wiring continuity for Cat5, Cat6, Cat6a, telephone, USB and coax cable assemblies at the press of a button.
-
product
Outdoor Temperature Sensor
ENVIROMUX-STS-O
Applications from -40 to 185°F (-40 to 85°C). Accurate to within ±0.9°F (±0.5°C). Weatherproof enclosure. High resistance to external influences on the cable due to digital output signal. Re-calibration is not necessary after initial set-up. Quick release waterproof RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,942,123 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
HDMI HDBase-T Extender with IR & RS232/Ethernet via One CAT5/6
ST-C6HDE-HDBT
The XTENDEX® HDMI HDBase-T Extender transmits uncompressed digital HDMI signal, IR, RS232, and Ethernet up to 328 feet over a single CAT5e/6/7 cable using HDBase-T technology. Each video extender consists of a local unit that connects to an HDMI source and a remote unit that connects to an HDMI display.
-
product
M2T Transmitter
The M2T half-rack transmitter houses two stereo transmitters to provide two stereo audio channels, and for up to four mono audio channels in a single rack space. The audio inputs can be individually configured to be analog or Dante compatible. The analog input connectors are full-size XLR/TRS combo types for balanced line-level analog signals while the input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. A Dante™ Ultimo™ interface via dual RJ45 connectors accepts Dante networked audio inputs and can daisy chain the digital stream to additional units via CAT6 cables. An additional RJ45 jack provides an Ethernet connection for programming and control via Wireless Designer™ software and a USB jack on the front panel allows for firmware updates. The transmitter features a full color, backlit LCD for high visibility in any environment, while the chassis is all-metal and can be racked singly or in pairs using included rack mount hardware.
-
product
Bench Digital Multimeter, Calibrated, Data, 1 kV, 10 A, 3.8 Digit
72-1015 CAL D
The 72-1015 CAL D from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
product
PCI Express Gen 1 Test Backplane
SKU-015-01
The PCI Express Test Backplane was designed to support production testing/debugging of PCIe-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into one x4 and three x1 PCI Express slots via 7 ft CAT6 cable.
-
product
4-20mA Sensor Converter
ENVIROMUX-S420MA-24V
External RJ45 device monitors up to two 4-20 mA analog sensors. Supports ISA Type 2, ISA Type 3, and ISA Type 4 sensors. Provides 24VDC, 25mA for each sensor. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 500 ft. (152 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: RoHS.
-
product
Professional Cable Tester
1EA560
Multifuncional tester with LCD display enables to show wire maps and combination of pairs and their lenghts. It also measure the lenght until the broken line / cable. It is suitable for CAT5, CAT5E, and CAT6 cables. With special interface is also suitable for testing of coaxial and telephone cables. It has special unit for testing of cable ends in the other room.
-
product
PCI/PCI Express Expansion Backplane
SKU-075-0X
PCI/PCI Express Expansion backplane was designed as a universal solution for Desktop or Laptop host computer expansion.It allows adding up to 4 PCI and up to 2 PCI Express boards to the host computer. Expansion backplane can be placed inside any general-purpose computer chassis and connects to the host computer via 5ft (or 10ft) CAT6 cable.
-
product
VTAC, Patchcord, ITA, 36", VTAC, CAT6, To RJ45
7-141893694-036
VTAC, Patchcord, ITA, 36", VTAC, CAT6, to RJ45
-
product
Legacy Liquid Detection Rope Sensor
ENVIROMUX-LDSx-y
For warning of flooding. Detects liquid depth >0.1" (2.5 mm). Minimum puddle: 0.6" (15 mm) diameter. 100% waterproof electronics. Detects any liquid or moisture, except deionized water. RJ45 connector. Voltage Supply: 12VDC. Current Consumption: 20mA. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Available water sensor cable (x) lengths: 1/10/50/100/200/400/600/800/1000 feet. Plenum rating: CL2P (UL). Available 2-wire cable (y) lengths: 5/10/20/50/100 feet. Powered by ENVIROMUX-SEMS-16U and SERIMUX-S-x. Regulatory approvals: CE, RoHS. Requires the ENVIROMUX-SEMS-16U and SERIMUX-S-x to operate. Use self-adhesive clips (ENVIROMUX-CLP10-LD) to prevent sensor rope cable from shifing after installation. ENVIROMUX-CLP10-LD includes 10 clips.
-
product
Network Tools & Testers
Tripp Lite's Multi-Functional Network Cable Tester allows you to test wiring continuity for Cat5, Cat6, Phone and Coax cable assemblies. Identifies mis-wires, short circuits and open circuits. Features two piece transmitter and receiver, two BNC-F coax converters and coax terminator. Includes handy storage pouch when not in use. Power supplied by 9V Battery (not included).
-
product
FTP Patch Cable, 5″ C6, 4/Clam
#610025C
Platinum Tools’ premium 5″ Cat6 FTP Patch Cables are made with testing networks in mind. Plug in and out all day long and know you will have consistent and precise connectivity every time. Designed for repititive, long cycle life! 849160007951
-
product
Low Cost Splitter Systems
RATCAT Family
The CAT Snake Stage Box allows four lines of balanced analog audio to be run down a shielded CAT5/6/7 cable. Each of its four channels can carry balanced analog, AES/EBU, DMX, and Clear-Com signals hundreds of feet away. The CAT Snake is a fully passive unit which can be input directly into analog or digital consoles. Each channel is isolated which means channel 1 can send a DMX Signal while channel 2 is sending balanced analog all down the same shielded CAT5 cable. Multiple CAT Snake stage boxes can be daisy chained to allow the same four analog channels to be dropped in multiple locations. Each CAT Snake stage box has an Ethercon input and Ethercon parallel output that allows the CAT Snake to be used as a hard-wire split.
-
product
Network Cable
Maximum speed 50 micron GOLD-PLATED contacts ensures the maximum speed is achieved through low resistance and signal degradation.Heavy Duty durability Lasts up to 10 times longer than other cables due to advanced protection against atmospheric corrosion and low friction.Network support CAT 5e cable will support Ethernet, Fast Ethernet, and Gigabit Ethernet. CAT 5e Cable is completely backwards compatible, and can be used in any application in which you would normally use CAT 5 cable.
-
product
5VDC Sensor Converter, 5VDC, 15mA
ENVIROMUX-S5VDC-5V
External RJ45 device monitors up to two linear DC sensors, 0VDC ~ 5VDC. Output for each sensor: 5VDC, 15mA. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,956,288 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
PCB Adapter, ITA, SIM, VTAC, 16 Pos, 6 Slot, to (1) Cat6
510171105
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat 6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules. Please note this part is too wide for use in multiple adjacent slots.
-
product
PCI Express Expansion Backplane
SKU-076-0X
PCI Express Expansion backplane was designed as a universal solution for Desktop or Laptop host computer expansion. It allows adding up to four additional PCI Express boards to the host computer. Expansion backplane can be placed inside any general-purpose computer chassis, and connects to the host computer via 5ft (or 10ft) CAT6 cable.
-
product
230V AC Socket Tester With RCD Test (For UK)
1944
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 230VAC circuits.*Neon indicators.*RCD Test.*30mA leakage current measurement.*Detect faulty wiring status in 3 wire receptacle.*Various combinations of 3 neon idnicators tell if wiring is OK or 6 possible faulty conditions.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 1.5W*Frequency: 50Hz
-
product
Carbon Monoxide Detector, CO
ENVIROMUX-CMD
Continuous air monitoring. Pre-set alarm points alert at: 70 ppm after 60 to 240 minutes; 150 ppm after 10 to 50 minutes; and 400 ppm after 4 to 15 minutes. Flush or surface mount. Test functionality of electrochemical CO sensing cell. Connect to RJ45 or digital input sensor ports. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1000 ft (305m). LED indicators for operation status and system test. Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL.
-
product
DC Voltage Detector
ENVIROMUX-S60VDC
Monitors up to two DC voltages: -60VDC ~ 0VDC or 0VDC ~ 60VDC. Connector: Screw Terminal, 5-position. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Includes Mounting Hardware. Operating temperature: 32 to 158°F (0 to 70°C). Regulatory approvals: CE, RoHS.
-
product
Outdoor Infrared Motion Sensor
ENVIROMUX-IMD-O
Outdoor weatherproof - high reliability against water and insects. Double conductive shielding to eliminate false alarms from light sources. Registers movement in the area covered: 40 ft (12 m) x 50 ft (15 m) - 120° wide. LED lights during detection. Selectable detection paterns: Multi-Level (40 zones) or Pet Alley (18 zones). Unwanted detection areas can be eliminated using the included area masking strips. Selectable Sensitivity: High, Mid and Low. Adjustable to the brightness of surrounding environment with the Day/Night Mode switch. Tamper switch opens when cover is removed. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: -4 to 122°F (-20 to 50°C). IP54 compliant. Powered by ENVIROMUX-2D/5D/16D.
-
product
LiFi HotSpot Evaluation Kit
The Li-Fi HotSpot Evaluation Kit allows the establishment of an optical wireless bidirectional point-to-point full-duplex data connection over medium distances in the meter range. Data rates of up to 1 GB/s are supported at a distance of up to 5 meters. The kit consists of two Li-Fi HotSpots, two CAT-6 cables (RJ45), two external power supplies and a user manual. Users can thus get to know the technical advantages of Li-Fi technology with little effort and test and evaluate them in their own network or environmental conditions.
-
product
Smoke Detection Sensor - CE Approved
ENVIROMUX-SDS-CE
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.08-0.14 dB/m. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
32-bit PCI Test Backplane
SKU-014-01
The 32-bit PCI Test Backplane was designed to support production testing/debugging of PCI-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into four 32-bit PCI slots via 7 ft CAT6 cable. The PCI backplane is a versatile platform that allows you to test up to 4 PCI boards at the same time, facilitates easy access to logic signals, provides hot-swap compatibility, and per-slot overcurrent protection.
-
product
230V AC Socket Tester(For UK)
1942
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 230VAC circuits.*Neon indicators.*Detect faulty wiring status in 3 wire receptacle.*Various combinations of 3 neon indicators tell if wiring is OK or 6 possible faulty conditions.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 1W*Frequency: 50Hz
