Up Converters
Increase the frequency of a signal.
-
product
Modulation Distortion Up To 53 GHz
S95070B
S95070B software enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 53 GHz. The wide dynamic range and vector error correction of the PXI VNA results in an extremely low residual EVM from the test setup, giving you a complete picture of your device’s performance without test system interference. S95070B software measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals through spectral correlation between the input and output spectrum, without doing demodulation. Integration with the PXI VNA’s measurement flexibility enables you to do quick modulation distortion measurements along with traditional VNA tests.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5942-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
NI-9775 , ±10 V, Up to 20 MS/s/ch, 14-Bit, 4-Channel C Series Digitizer Module
784539-01
The NI-9775 provides referenced single-ended analog inputs with two timing modes for applications such as fault detection in electrical transmission lines or structural failure events. You can use the NI-9775 to measure finite samples up to 20 MS/s/ch to capture fault detections or to measure continuously at up to 4 MS/s. You also can use the built-in analog reference trigger to assist with high speed phenomena. Additionally, the NI-9775 supports waveform streaming at a lower sample rate.
-
product
High Temperature Up To 230°C (446 °F) Inductive Sensors
Contrinex High Temperature Up To 230°C (446 °F) Inductive Sensors
-
product
16-Bit PCIe Gen-2 Digitizer 4 Channels 100 MS/s Up To 16GS Memory
Oscar-16 Express / CompuScope 4447
The GaGe Oscar TM family of multi-channel digitizers features up to 4 channels in a single-slot PCI Express or PCI card with up to 100 MS/s sampling per channel, and up to 16 GS of on-board acquisition memory.
-
product
Gaming Platform Based On AMD® Ryzen V2000 Processors, Supporting Up To Eight Independent Displays, Including 4K UHD
ADi-SA3X-RZ
ADLINK‘s ADi-SA3X-RZ all-in-one gaming platform features powerful processing and graphics performance for gaming and retail. Equipped with AMD® Ryzen V2000 processors, the ADi-SA3X-RZ provides compelling graphics performance from a PCI Express 3.0x16 discrete graphics card and/or an AMD® Radeon™ Graphics supporting up to eight independent monitors.
-
product
Time to Amplitude Converters and Calibrator
A Time-to-Amplitude Converter (TAC) can achieve exceptional precision by using an analog technique to convert small time intervals to pulse amplitudes. When a timing application demands picosecond precision, a time-to-amplitude converter is a prime candidate. A time-to-amplitude converter is a productive solution for measurements less than 10 μs when time resolutions from 10 ps to 50 ns are required.
-
product
Dynamic Digital I/O (3U), 32 Ch., Per Pin Control, Up To 100 MHz W/256MB Memory & LVDS
GX5292
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 32 ch., per Pin Control, up to 100 MHz w/256MB Memory & LVDS
-
product
High Speed PXIe Digital IO Card - 32 Channels, Extendable up to 256 Channels in One Chassis
Model 33010
Chroma 33010 is a high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO Card consists of a Sequencer Pattern Generator (SQPG) and 32 Channels of fill ATE-like features. The 33010 IO card is expandable up to 356 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
product
Synchro to BCD and Resolver to BCD Converters
TSBC TRBC
Computer Conversions Corporation
The TSB Series are miniature, high performance, continuous tracking, synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
product
CompacFrame Type 39A, up to 5 slots, VITA 48.8 AFT
Type-39A
Elma’s all new CompacFrame platform accelerates the development and test of 3U plug-in-cards (PICs) designed according to VITA 48.8, Air Flow Through Cooling standard. The 3U card cage in the platform is tilted upwards by 5° for easier card access.
-
product
AC/DC Converters
Start-Power manufactures single and three-phase unidirectional analogue AC-DC Converters and single and two-directional three-phase digital AC-DC Converters. One- and three-phase unidirectional analogue AC/DC Converters can be used as motor controls or as power supplies in sizes from 40A up to 500A. Three-phase uni- and bidirectional digital AC/DC converters are suitable for speed and torque control of motors.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 8 Channels (Single Channel) or 4 Channels (Differential)
M2P.5913-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
High Voltage Dry Reed Relays For up to 15 kV
SERIES 62 & 63
ungsten switches with power rating of 50 Watts maximum? Three switch types:5kV stand-off, 3.5kV switching10kV stand-off, 7.5kV switching15kV stand-off, 12.5kV switching? Series 62 has push-on connectors on top face for EHT and solder pins and nylon studs on the underside for PCB mounting
-
product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
-
product
Sample Rate Converters
Analog Devices’ portfolio of sample rate converters features industry-leading performance in both audio performance and conversion ratios. These converters can be used in high end consumer applications, as well as in price conscious consumer applications.
-
product
Partial Discharge Test Set Up
This testing set is of great use in industries for various testing applications. We strictly follow all the guidelines while manufacturing this Partial Discharge Test Set Up.
-
product
PICMG 1.3 Half-size CPU Card With Intel® Celeron® Processor J1900 (up To 2.42 GHz), SATA2, CFast™, VGA/LVDS And Dual LANs
SHB215
*Intel® Celeron® Processor J1900 up to 2.42 GHz*1 DDR3L-1333/1600 SO-DIMM, up to 8GB*VGA and LVDS with dual-view supported*1 CFast™ socket onboard
-
product
Signal Converters For Computer-aided Measurement
EIB 700 and IK 220 series
*Ideal as evaluation unit for high encoder signal resolutions and rapid measurement*EIB 700: connection of multiple evaluation units with Ethernet transmission and, for example, wireless LAN transmission paths*EIB 700: connection of up to four HEIDENHAIN encoders*IK 220: PCI counter card*IK 220: connection of up to two HEIDENHAIN encoders
-
product
Lan Digitizer / Oszilloscope With 8 Bit, 1x2GS/s Or 2x1GS/s Up To 8 GS Memory
Cobra-X
The GaGe FCiX Cobra/CobraMax LAN digitizer features 2 channels of 8-bit resolution with a maximum sampling rate up to 2 or 4 GS/s for one channel and up to 1 or 2 GS/s for two channels and true Effective Number of Bits (ENOB) up to 7.6-bits with 10 MHz input.
-
product
SIMRC - RS232 to I2C Converter PCB
1080-001
Pickering Interfaces Series 1000 SIM Reed Relay Cards offer a choice of switching configurations using low cost industry standard SIM connectors. They are ideal for placing switching systems in fixtures close to the unit under test.
-
product
ESD Latch Up Tester
1100-ESD
Tokyo Electronics Trading Co., Ltd.
The Model 1100-ESD can easily and accurately perform ESD tests (HBM, MM) on ICs up to 64 pins. Also, all common pin combinations required by the standard can be realized.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5941-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PXIe-1085, 18-Slot (16 Hybrid Slots, 1 PXIe Timing Slot), Up to 24 GB/s PXI Chassis
781813-01
PXIe, 18-Slot (16 Hybrid Slots, 1 PXIe Timing Slot), Up to 24 GB/s PXI Chassis—The PXIe‑1085 features a high-bandwidth, all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
product
USB-to-Serial Cable Converter
This cable is the solution for users who want to communicate with GE Multilin IEDs via PCs that have USB communication ports. Using this cable is quick and easy. Simply install the cable driver on your PC, plug in the cable and you are ready to communicate.
-
product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 4 Channels
DN2.653-04
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, up to 80 MS/s on 8 Channels
DN2.656-08
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
product
- RS-232 to RS-422 Interface Converter
Model 263
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 4.0 W250 | VP 210157
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans, and with high vehicle throughput and increased loads.
-
product
RF Amplifiers up to 1000 MHz
Narrow and Broad band high power RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAs in Class A and Class A/B topologies for Pulse, AM, FM, continuous wave and digital modulation applications that include EW, Radar, Jamming, EMI and EMC radiated immunity, and wireless communications testing.
