Analog Digital
-
Product
Analog & Digital Gas Controller
MX 32
-
Teledyne Gas & Flame Detection
We introduce the new MX 32, a controller that takes analog & digital inputs and covers all needs for a wide variety of applications.The MX 32 is a compact, low-profile controller that continuously monitors gas detection and more generally any 4-20 mA, MODBUS RS485 signal from compatible detectors.
-
Product
Analog & Digital Audio Platform
BAT
-
Our fully flexible and application-optimized solution to enable high-fidelity audio and voice-control of IoT devices at low power cost
-
Product
System of High-Speed Synchronous Registration of Analog, Digital, and Video Signals
-
The system uses a high-performance NI CompactRIO controller to simultaneously register 24 analog signals, receive an accurate digital pulse from GPS and synchronize measurements.The video signal is recorded using a high-speed camera connected to an NI PCIe-1433 frame grabber. The information received from the camera and the recording device is transmitted to a server built on the basis of an industrial computer, which writes data to an external 12-disk RAID array. The stream of recorded data in the system can reach 600 MB per second.
-
Product
Analog & Digital I/O Modules
-
USB analog and digital I/O modules are a complete family of data acquisition modules for use in process control systems. The analog input modules can measure process signals such as DC voltage, thermocouples, 4-20mA current loops, discrete contact closures.
-
Product
Analog and Digital Front Ends
ACQUA Front Ends
-
Measurement Front Ends (MFEs) convert the digital test signals of the communication analysis system ACQUA to the analog or digital formats required by terminal equipment, acoustic transducers, networks, network components, or system simulators, thus allowing complete tests in both transmission directions.
-
Product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
RF Signal Generator
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
PXIe-5651, 3.3 GHz RF Signal Generator
PXIe-5651 / 781216-01
RF Signal Generator
PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
ISA Data Acquisition Boards
A-812PG
-
A-812PG is a 12-bit multifunction analog and digital I/O board for PC/AT compatible computers. A-812PG offers 16 single-ended plus two channels of analog output with 12-bit resolution. A-812PG has 16 digital inputs, 16 digital outputs, and one timer/counter channel. A-812PG Provides gains of 1, 2, 4, 8, and 16. It has a maximum sampling rate of 62.5K samples/s. DMA operation is jumper selectable for levels 1 or 3. Interrupts are jumper selectable between 3 and 15.
-
Product
PCIe-6353 , PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device
81049-01
Multifunction I/O
PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device - The PCIe‑6353 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality … leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6353 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Mezzanine System
5188
System
ECM P/N 5188 provides an AD8109 crosspoint switch for analog or digital signals with 250MHz of Bandwidth. For single ended applications 8 inputs can be connected up to 8 outputs in any configuration.
-
Product
12-bit, 100KHz, 16SE/8DIFF Isolated Analog Input Board
APCI-3001-16
-
16 single-ended or 8 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
782251-01
Multifunction I/O
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Full-Featured Video Frame Grabber
Nexeon HD
-
Nexeon HD is a full-featured video frame grabber for high-definition video display and capture. It supports video inputs from standard and HDTV resolutions as well as VGA display. Nexeon HD has a flexible input interface complete with an HDMI compatible receiver and supports both analog and digital DVI/HDMI standards.
-
Product
Frequency Counter, 30MHz to 800MHz, 500MHz to 2.8GHz, 7 Digits
72-7390
-
Rugged instrument is smaller than a deck of cards, yet provides frequency measurement of digital, on/off keying and analog signals from 30MHz to 2.8GHz. It is perfect for displaying the output of two–way radio equipment, analog and digital cell phones, RF remote controls and many other items. Internal vibrator alert also makes this an outstanding device for detecting transmitters in counter–surveillance applications
-
Product
USB-6346, 8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
785814-01
Multifunction I/O
8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB-6346 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6346 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Digital Control VGAs
-
Analog Devices digital controlled variable gain amplifiers provide discrete levels of gain control over a fixed number of control bits for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust the amplitude of a signal in real time, which is critical for a number of applications involving ultrasound, speech analysis, radar, wireless communications, and instrumentation. We also offer a portfolio of voltage controlled VGAs to provide you with continuous gain control over a wide dynamic range.
-
Product
cDAQ-9174, 4‑Slot, USB CompactDAQ Chassis
781157-01
Chassis
4‑Slot, USB CompactDAQ Chassis - The cDAQ‑9174 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9174 also has four 32‑bit general-purpose counters/timers. With multiple timing engines, you can run seven hardware-timed operations simultaneously, with three independent rates for analog input.
-
Product
DC DC Converter Models
-
These versatile DC-DC Converters are ideally suited for powering a wide variety of analog and digital circuitry, such as op amps, logic and microprocessors. They may be mounted directly on a printed circuit board for OEM applications, or installed in a socket for developmental and small quantity requirements.
-
Product
PCIe-6343, PCI Express, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device
781047-01
Multifunction I/O
PCI Express, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device - The PCIe‑6343 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PSD Signal Processing Tool
SEEPOS
-
For most position measurement applications the SiTek SEEPOS system offers a complete and easy-to-use solution. High speed PSD electronics combined with digital signal processing and high speed USB data transfer gives a powerful measurement system. With its large dynamic range it can handle light powers from nW to mW from DC light sources as well as modulated light sources. All parameters, such as PSD bias voltage, amplifier gain, the use of analog and digital filters etc., are easily controlled from the included software and light spot position is continuously displayed both in XY and X-t, Y-t graphs. Optimized plot algorithms ensure that all data is visually seen on the screen even in full speed measurements. Included tools for data analysis and visualization simplify rapid scan through large data sets in order to find specific parts of interest.
-
Product
Class-D Audio Amplifiers
-
Analog Devices is a leader in Class-D audio amplifiers and audio signal processing, and we deliver audiophile-level performance with our proven analog and digital technology. We offer a wide range of audio amplifiers, including industry-leading microphone preamps, microphone drivers, line drivers, and receivers. Our Class-D amplifiers, in particular, are among the lowest power and lowest distortion in the industry. Our portfolio includes Class-A, Class-B, and Class-D audio amplifier offerings, along with a breadth of power ICs. Analog Devices amplifier products have been used in many high volume consumer products where the highest audio quality is expected. The lowest power consumption also enables this performance in many battery powered applications as well.
-
Product
4AO/4DI IoT Modbus/SNMP/MQTT 2-Ports Ethernet Remote I/O
ADAM-6224
-
4ch analog output/4ch digital inputProtocols:MQTT(TLS),SNMP,Modbus TCP,RESTful,ASCIIGCL to perform basic logic control rulesCloud access: Data update to AzureAuto-bypass function to ensure daisy-chain data transmissionPeer-to-Peer function to map I/O statusBuilt-in web serverWatchdog timer to recover the system
-
Product
LilyPad Temperature Sensor
-
Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical touch based on body heat and ambient conditions with this small sensor.
-
Product
RMS Averaging Vibration Sensor
SQ-SVS
-
The vibration sensor module performs calibrated averaging (root mean squared) vibration measurement with analog voltage and digital serial outputs. Because acceleration signals are extremely fast by nature, they require high speed sampling and computationally intensive processing to measure.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 2 GHz, 4 Analog Plus 16 Digital Channels
MSOS204A
Oscilloscope
2 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.5 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
PXIe-6376, 8 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
781475-01
Multifunction I/O
PXIe, 8 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6376 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6376 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Arria 10 FPGA Card
CP-FPGA-5
-
The Arria 10 FPGA PCIe card features a powerful field programmable gate array chip that supports both analog and digital I/O. Each card’s I/O functionality is fully customizable by the user by means of the FPGA Workbench tools. The cards are available with 480K or 1150K logic elements. There are two High Pin Count FMC Style Positions available for the High-Speed Daughter Cards.
-
Product
Process Analyzers
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Industrial meters for pH, ORP, conductivity and oxygen. In 2- and 4-wire technology, explosion-proof.Bus Communication: HART, FOUNDATION Fieldbus, Profibus DP and PA. Robust industrial housing with high IP protection. Suitable for outdoor use. For analog and digital sensors. Simple intuitive operation. From DIN rail transmitters up to the modular system.
-
Product
USB-6356, 8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782260-01
Multifunction I/O
8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6356 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6356 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Temperature Sensors
-
ST’s temperature sensor portfolio includes both analog and digital temperature sensor ICs. Both types are suitable for a wide range of applications including industrial, consumer, portable, medical, home appliances and computer market segments, thanks to their high accuracy and low-power consumption.
