1553 Interfaces
Mil-Std-1553 interfaces.
-
Product
SD / USB Interface
-
Advantech SQFlash industrial storage modules provide SD interface products such as SD, Micro SD. USB DOMs and eMMC products are also available with optional wide temperature support to fit industrial applications.
-
Product
POWER INTERFACE BOX
-
The POWER Box is in charge to provide power supply lines towards the UUT simulating the power distribution unit. The box has been designed to host, in any mixed configuration, two kind of plug in modules:
-
Product
GPIB to Relay Interface Boards
Model 4864 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
Product
cPCI Intelligent Interface Card
IIB-1553-CPC
-
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.
-
Product
Ethernet To Parallel Digital Interfaces
-
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Analog and Digital Interface
425
-
Three quadrature encoder channels with 16-bit countersFour 12-bit D/A outputsEight 12-bit differential A/D inputs, 50 kHz rateWatchdog timerForty-eight bi-directional digital signals for solid state relay boardsPC/ISA compatible
-
Product
Interface Cards, Cables, and Modules
-
Keysight Technologies Interface Cards, Cables, and Modules
-
Product
Analog Interface Boards
Model 4861B OEM
-
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
Product
Network Interface Card
PMC-GBIT-DT2BP
Interface Card
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
Product
Network Interface & Acceleration Cards
-
Advantech's PCIe accelerators and network interface cards bring high-speed connectivity and fast packet processing to network appliances and servers.
-
Product
Network Interface
-
VadaTech offers AMC Network Interface Cards (NICs), FMC networking modules and ATCA rear transition modules (RTMs) with a wide range of connector interfaces to make it easier for you to integrate an embedded computing system into your solution.
-
Product
Ethernet Parallel Interface
Model 8003
-
* Provides 40 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has vertical Ethernet and Digital IO connector on the component side. * Optional Relay Driver board adds 4, 32 or 40 Relay Drivers. • Apply regulated 5 Vdc power through the Digital IO connector.
-
Product
NI-9852, 2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
779707-01
CAN Interface
2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI-9852 is a fault‑tolerant Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9852 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9852 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9852 is only compatible with CompactRIO systems.
-
Product
PCI Express Mini Card For MIL-STD-1553 Test And Simulation
AME1553-1
-
MIL-STD-1553 Test and Simulation PCI Express Mini Card with 1 Dual Redundant channel plus 2 discrete Input, 2 discrete Output channels.
-
Product
Interface Connectors
-
High durability Interface connectors do not damage the product, side terminal by a special mechanism, and do not lock, making it suitable for automated inspection.
-
Product
DAQ User Interface Software
DAPstudio 3.00
-
If you need to deliver a data acquisition system quickly and you want to develop a good user interface for it, then download DAPstudio 3.00 and see how that could help. You now can use the latest (full) version of DAP Measurement Studio software from Microstar Laboratories, maker of Data Acquisition Processor (DAP) boards and software, for an unlimited trial period at no charge.
-
Product
PCI Intelligent Interface Card
IIB-1553-PCI
-
The IIB-1553-PCI is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PCI bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Desalter Interface Level Transmitter
-
This reliable level transmitter is specially designed to maximize the throughput of oil/water separators and accurately measures the electrical interface in the emulsion even in upset conditions. This measurement is critical because the separation vessel operates at maximum efficiency when the electrostatic grid is close as possible to the interface.
-
Product
ROM USB port interface
EeRom-8U
-
EeRom-8U ROM Emulator is aimed at developers who focus on making ROM based programs and data including embedded systems, BIOS, video games, robotics, printer drivers, graphic controller, postscript interpreters, character font libraries, and other ROM based application
-
Product
Genrad 2270 Interface Receivers
GR Series
-
The 3210 Series Receiver is designed for interfacing the GR 2270 style test fixture. Using patented CAM/TRAC design, the 3210 Receiver provides an accurate, positive locking system that ensures consistent contact throughout the entire interface. With a 5/8" stroke, the 3212 Receiver allows additional clearance for coax and custom block applications.
-
Product
FPGA UDP Packet Interface Connnecting 3-4 Channels of MIL-STD-1553 to Ethernet in Real-Time
ENETX-1553
Ethernet Interface
ENETX-1553™ is an innovative product that provides “remoting” of 1553 operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). ENETX-1553 is a small, low-power, rugged device that provides real-time Ethernet connectivity to for three or four dual redundant 1553 (A/B) buses (channels). Ideal for remoting 1553 connections for in-field applications or point-point lab usage. AltaAPI provides and highly portable BSD SDK and National Instruments LabVIEW and LabWindows. ENET products are unique in the market as they have a hardware, FPGA real-time UDP engine – no OS or IP stacks – provides maximum throughput and ultimate virus protection.
-
Product
Four Port RS-232 Interface
PCI-COM232/4
-
Serial ports: 4Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with fanout cable to 4 DB-9 or DB-25 male connectorsPower: +5V only
-
Product
USB-8501, 1-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786306-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
RS-232 to RS-422/RS-485 Interface Converter
Model 9365
-
FEATURES: DIN Rail Mountable; User Selectable RS-422 or RS-485; User Selectable Two- or Four-wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 kbp.
-
Product
Interface RS-232
-
The RS-232 specification allows for reliable data transmission from one transmitter to one receiver at data rates of up to 20 kbps over relatively short distances (up to 50 feet). On more recent RS-232 transceiver chips, data rates of up to 1 Mbps are achievable over shorter distances (up to 5 feet). The most common applications for RS-232 transceivers are computers and peripherals, mobile phone data cables, and diagnostic data ports.
-
Product
COM-HPC Server Type 10G OCP Mezzanine Card
OCP-4x10G-SFP+
Network Interface Controller
- Supports up to four 10GbE Fiber interface (10G-SFP+)- Compatible with PICMG COM-HPC Rev 1.0 Server Type compliant- For COM-HPC-ALT module
-
Product
DMX to Analog Interfaces
-
The MTX-DE48 decodes signals from DMX control desks to analog dimmers. It is used to integrate DMX controllers into existing analog installations. The standard 0 to 10V output is compatable with many LED drivers. Output may be adjusted up to 28V for use with some older dimmer systems. A negative output voltage option is also available.
-
Product
Air Interface Emulator
-
Becker Nachrichtentechnik GmbH
With help of air interface emulators radio field propagations can be emulated reproduceable in laboratory environments. For different applications like cellular, wireless networks or broadcast several types of devices are available.
