Impulse Voltage
-
product
Digital Clamp Current Tester For High Voltage
HCL-36UX
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Display measurement value on your smartphone through blue-tooth connecting.・Measurement value can be kept in the our cloud server.・In addition to measured values, location registration by GPS, temperature, date and time can also be saved.
-
product
PXI/PXIe High Voltage Multiplexer, Dual 4-Channel, 1-Pole
42-321-100-HI
The 40-321-100-HI (PXI) and 42-321-100-HI (PXIe) are dual 4-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Solid State Voltage Injector
J2110A
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
product
High Voltage 9 Pin D-Type Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
PXI Dual 12:1 High Voltage Power MUX
40-331-002
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
product
LXI High Voltage Matrix 2-pole 300x2
60-310-302
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
1kV, 120 MHz High Voltage Differential Probe with Auto Zero Disconnect
HVD3106A
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
100-600V AC Non-Contact Electric Voltage Detector With Buzzer
1969
Peaceful Thriving Enterprise Co Ltd
*With cUL and RoHS Approval.*Check voltage on 100-600V AC.*Two LR44, 1.5V batteries which is included.*Audible and visual indication for easy operation.*Four-section power and sensitivity switch (H, L, M and off).*Locates breaks along live, insulated wires and power cords.
-
product
12-600V 2-Pole Voltage Tester
1964B
Peaceful Thriving Enterprise Co Ltd
The 2 pole Voltage Tester provides a clear indication of AC or DC voltage levels via bright LED's from 12-600V. It is constructed in accordance with the latest safety standards and is ergonomically designed which is durable enough for both industrial and domestic uses.
-
product
12-bit, 4 Analog Voltage Outputs With Separate Grounds, Optically Isolated 500 V
APCI-3504
4 analog output voltage channels with 500V optical isolation, 12-bit resolution, each output has its own ground line.
-
product
Voltage Breakdown Testing Machine
DRK218
Shandong Drick Instruments Co., Ltd.
DRK218 breakdown voltage tester is controlled by the computer, through a new smart digital integrated circuits developed by my company and software control system to make the step-up rate is truly uniform, accurate, and be able to accurately measure the leakage current data. Real-time rendering test curve accurate judgment and it can save, analyze and print test data.
-
product
AC High Voltage Breakdown Tester
CIE / 5050A
Cambridge Instruments & Engineering Co.
'CIE' A.C. High Voltage Breakdown Test Set is ideal for fast accurate & reliable testing of withstand/Breakdown test of electrical & electronic materials, components, equipments, panel boards, etc.
-
product
LXI High Voltage Switching - 10xSPST Plugin Module
65-233-904
The 65-233-904 plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
LXI High Voltage Switching - 3-Bank, 1-Pole, 12:1 Multiplexer Plugin Module
65-231-905
The 65-231-905 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
Voltage, Continuity, and Current Tester
FLIR VT8-Series
The FLIR VT8-Series are high-quality voltage, continuity, and current testers. They feature an optimized, open-jaw design that can fit into tight spaces and reliably measure large-diameter cables. The VT8-600 carries a CAT III-600 V/CAT IV-300 V safety rating and a 100 A/600 V measuring range, while the VT8-1000 carries a CAT III-1000 V/CAT IV-600 V safety rating and a 200 A/1000 V measuring range. Extensive measurement features make the VT8-Series versatile tools – just one meter can get the job done.
-
product
400 MHz High Voltage Differential Probe
DP0001A
The DP0001A is a 400 MHz high voltage differential probe with 2 kV mains isolated or 1 kV CAT III rating designed for making accurate high-voltage power measurements required for testing today’s WBG power devices, power converters or motor drives.
-
-
product
High Voltage Standard
HVS
The HVS uses precision matched resistors for high accuracy; it is a modified Park divider structure.
-
product
Easy Connection Of IEPE Sensors To Voltage Input Measurement Devices
K- IEPE
Our K-IEPE module is designed to connect IEPE sensors to a voltage measurement device that normally cannot support IEPE sensors. The powered K-IEPE module simply enables IEPE sensors to be connected via the BNC terminals and will output the signal voltages to an analog measurement device.
-
product
Voltage Monitoring, Timer Delay-on -off, 4 Pole
MTDV4 Relay
Plug-in electronic voltage monitoring relay with optional delay-on and delay-off timer function and four change-over contacts. The delay time is adjustable with a lockable knob (either delay-on or delay-off, the other delay is fixed). The relay can also be supplied with fixed time delays (no knob). The pull-in voltage and drop-out voltage are both adjustable via internal screws. The relay can also be supplied with a fixed pull-in and drop-out voltage. Suitable for monitoring DC voltages.
-
product
Voltage Variable Attenuators
Voltage variable attenuators (VVAs) that offer up to 60 dB of attenuation across a broad range of frequencies from 400 MHz to 18 GHz. These voltage variable attenuators are frequently used in applications such as electronic warfare, instrumentation, point-to-point and point-to-multipoint radios, fiber optic and broadband telecom, microwave radio and VSAT, military radios, radar, ECM, SATCOM and sensors, and R&D.
-
product
1.5kV, 70 MHz, 2 pF, 10 M, Rise Time < 5 ns, High Voltage Differential Probe
T3HVD1500-70
1.5kV, 70 MHz, 2 pF, 10 M, Rise Time < 5 ns, High Voltage Differential Probe.
-
product
Voltage References
Analog Devices offers the widest selection of high performance voltage references in the industry. Our products range from high accuracy, low noise for high end industrial applications to general-purpose, low power for handheld, battery-powered applications. ADI is the ultimate source for design engineers looking for the perfect voltage reference that is cost effective, reliable, and dependable.
-
product
PXI 12xSPST High Voltage Power Relay Module
40-330-003
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
product
Oil Breakdown Voltage Tester
DTA 100 C
BAUR Prüf- und Messtechnik GmbH
Insulating oil testing with the BAUR DTA 100 C. The BAUR DTA 100 C oil tester is designed for continuous operation in the laboratory and is characterised by the combination of extraordinary features. As a high-performance device with a test voltage up to 100 kV, with clear breakdown detection and absolutely reliable measurement results even across several measurement sequences, the BAUR DTA 100 C is the leading testing device for users in the electricity and other industries and in testing institutes.
-
product
High Voltage 37 Pin D-Type Cables - Connector to Unterminated for Pickering
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 37-pin D-type connector.
-
product
High Voltage Industrial Resistors
HVI
The HVI series of high voltage industrial resistors feature zero inductance, an excellent range of tolerances, wide resistance values and unparalleled high voltage handling.
-
product
High Voltage, High Current Linear Amplifier
P200
The P200 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
product
Voltage Tester With Wire Stripper
7122A
Peaceful Thriving Enterprise Co Ltd
The product can measure AC voltage 10V to 1000V and DC voltage 7V to 1000V with polarity indication. All testing results will be displayed by LCD. This product can also measure continuity and RCD. Eventually, for the convenience of wire stripping and cutting, this product has combined the function of wire stripper.
-
product
sbRIO-9207, Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781069-01
Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module - The sbRIO‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection. Non-enclosed modules are designed for OEM applications.
