Stabilizers
-
product
Automatic Crossover, 1U High, 2400-Watt Voltage/Current Stabilizers
Series KLR
The KLR Power Supply Series are automatic crossover, 1U high, 2400-watt voltage/current stabilizers with a full rectangular output characteristic within the voltage and current ranges listed in the Models Table.For each model a multitude of limit models can be configured. Limit models allow the unit to be configured to maximum settings below the rated voltage and/or rated current. When a limit model is established the unit will not accept programming values above the user-defined limits.The standard KLR Models (no suffix) have built-in GPIB and RS 232 interfaces. The E-Series models (suffix E) have built-in GPIB and LAN interfaces. The LAN interface is an ethernet-based interface that allows multiple-user access via a standard web browser.
-
product
Linear Rack Mount Power Supplies Current Stabilizers, Programmable, Local/Digital/Analog Control, Ultra Low Ripple/Noise
Series CC
These current stabilizers with built-in, dual range current-sensing resistors and a full complement of meters and controls, are 1/6-rack size units designed to plug directly into their own carrier cases and rack adapters. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
product
Power Stabilizers
Manufacturer of a wide range of products which include 100 KVA Power Stabilizer, Three Phase Power Stabilizer, Electric Power Stabilizer, Industrial Portable Stabilizer, 50 KVA Power Stabilizer and 100 Kva Power Stabilizer.
-
product
Manual Probearm for HBM and Flex-Pitch Applications
TPA-GFM
High Power Pulse Instruments GmbH
*Electrically isolated probearm for GND needle contact or general purpose DC, twin-wire HBM or flexible pitch VF-TLP/TLP/HMM/HBM force/sense probing based on the HPPI GF-A flexible pitch setup.*Suitable to mount the GF-A ground fixture needle for flexible pitch measurements. In addition a cable (e.g. for HBM) can be directly connected to the contact pin.*High stability
-
product
Full spectrum direct reading spectrometer
TY-9000
Wuxi Jinyibo Instrument Technology Co., Ltd.
The TY-9000 full-spectrum direct-reading spectrometer desktop spectrometer adopts international standard design and manufacturing process technology, adopts all-digital technology, replaces the huge photomultiplier tube (PMT) simulation technology, synchronizes with international spectrometer technology, adopts vacuum light chamber design And Full digital excitation source, leading CCD detector, high-speed data readout system, the instrument has high performance, very low detection line, long-term stability and repeatability.
-
product
One Axis Differential Interferometer
10719A
The Keysight 10719A One Axis Differential Interferometer makes either a differential linear or angular measurement for use in single and multiple axis applications. The linear measurement gauges the displacement between two objects, such as a stage and an optical column or inspection tool. The 10719A also measures either pitch or roll. An angle is measured when both reference and measurement beams measure to the same mirror. The 10721A provides high immunity to unwanted interferometer displacement, such as thermal expansion. It is a modular, compact design with monolithic optics for maximized mechanical stability. Use of a small 3 mm beam helps decrease Abb offset error.
-
product
Medium Range HD Multi-Spectral Surveillance System
TacFLIR® 280-HDEP
The TacFLIR 280-HDEP is an essential system for ground vehicle surveillance and fixed installations. With an all-new stabilized payload assembly for enhanced reliability, the TacFLIR 280-HDEP is ready for a variety of land missions, and the modular and scalable control electronics unit (CEU) is capable of hosting powerful video processing and Aided Target Recognition (AiTR), as well as third-party algorithms. Designed to meet the rigorous demands of military operations, the system delivers best-in-class EO/IR imagery and optional Display Interface Boards (DIB) which allow the operator to stream up to four independent video streams. In addition, there is also a removable terabyte hard drive w/DVR to record over 80 hours of compressed video and 250 screen captures.
-
product
Power Supply 302D
reliable and precise power of the output DC stabilization and digital LED displays. The output voltage is adjustable from 0 ~ 15V DC in smoothly with the knobs to control coarse and precise. Output current is regulated (limited) fluent in 0.6A ~ 2A. Securing the power supply protects it against accidental short circuits, and thus against overload and damage. In addition, the power supply has 5 fixed output voltages: 1.5 V, 3.6 V, 4.8 V, 6 V and 7.2 V, specially designed for mobile services, power systems and electronic components, etc. can be used in the design of electronic products, scientific work in laboratories, production lines and in teaching. Power can be used in the design of electronic products, scientific papers, laboratories, production lines and in teaching.
-
product
13.56 MHz 1250, 2500 and 5000 Watt High-Reliability RF Plasma Generators
GHW Series
The GHW Series RF power generators deliver maximum rated output powers of 1250, 2500 and 5000 Watts at a frequency of 13.56 MHz. The GHW generators offer field-proven reliability, exceptional stability, and unsurpassed repeatability for high uptime and process yield.
-
product
SparkFun Air Quality Sensor
SGP40 (Qwiic)
The SparkFun SGP40 Air Quality Sensor provides a measurement of the quality of the air in your room or house. The SGP40 is based on Sensirion's CMOSens® technology and uses a metal oxide (MOx) sensor with a temperature controlled micro hotplate and provides a humidity-compensated volatile organic compound (VOC) based indoor air quality signal. Both the sensing element and VOC Algorithm feature an unmatched robustness against contaminating gases present in real world applications enabling a unique long term stability as well as low drift and device to device variation.
-
product
Optical Chopper
These high stability variable frequency optical choppers each include a set of chemically blackened photoetched chopping discs. The mini chopper is an excellent choice for applications requiring a compact package. The chopping discs come in a variety of slot apertures and allow operation. Beam diameter is limited to 0.75mm when using the 200-slot disc and 1.0mm when using the 40 slot mini disc. The easy-to-interchange blades are made of non-magnetic, half hard brass and can be used in combination. Chopping frequency is set by adjusting a ten-turn dial or by applying an external DC voltage to the BNC input. Reference output is a TTL pulse and is in-phase with chopping action. The 5 digit led display gives a direct read-out of the chopping frequency. Power: 90-130V or 180-260V; 50/60Hz; 12VA max. Power supply included. Choppers are often used together with lock-in amplifiers.
-
product
Injection Transformer
J2101A
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
product
High Low Temperature Test Chamber
The high low temperature test chambers from Weiber are climatic test chambers, designed to simulate highly precise high and low temperature environments for the testing of electrical and electronics items, metallic products, automobile parts, food items, biological samples, chemicals, building materials and other wide variety of processed and packaged goods. These test chambers find widespread usage in manufacturing units, quality control units and scientific research organizations and are commonly employed for heat endurance test, cold endurance test and humidity and dryness endurance tests of products. These tests help in determining the product performance in specific environments and also help in identifying any manufacturing flaws and in determining its stability and shelf life.
-
product
Transformer Testing Panel
TRMS Voltage 600V /1200V Phase,1050V / 2100V Line TRMS Current 80A / 160A Direct USB , RS-232 / RS-485 interface & Free Software 20 X 4 LCD Display & Ultra Glow Red LED Display High Speed Measurement in 0.25Sec (Optional) Tamper Proof Calibration & Long term stability User Friendly Operation NABL certified in EQDC & ERDA
-
product
EMI Receiver
KH3931
Beijing KeHuan Century EMC Technology Co,.LTD
* Detection frequency range: 9KHz-30MHz * Frequency stability: 1X10-6 * Frequency resolution: (9kHz ~ 150kHz): 30Hz; (150kHz ~ 30MHz): 1kHz * Test error: ±2dB * Corresponding characteristics of pulse: in line with national standard GB/T6113.1-1995 * Detection time constant: in line with national standard GB/T6113.1-1995
-
product
2Wire Temp Transmitter
TS
● Accuracy: RTD: 0.5%, T/C: 0.75%● Wide selection of input● Low output ripple● High stability & low cost
-
product
PNA Microwave Network Analyzer
N5225B
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
PXIe Vector Network Analyzer, 300 kHz to 20 GHz
M9374A
Pay for only the frequency range you need with a choice of six frequency ranges up to 26.5 GHz Improve accuracy, yield and margins with the best PXI VNA speed, dynamic range, trace noise and stability Add functionality to your test system with a full 2-port VNA that fits in a single PXI slot Address your multiport applications needs by cascading multiple models Increase throughput and lower costs by adding modules in a multi-site configuration
-
product
Steady-state Solar Simulator For PV Modules
SORAS LS
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
product
Flex Power Right Angle Non Shut-Off Pulse Tools
The non shut-off right angle pulse tools are ideal selection when the operator needs to control the fastening process. It offers access for hard-to-reach fasteners in tight spaces. The drive on a right-angle tool is mounted at a 90-degree angle to the tool body. Designed for safe, reaction free operation for various industrial assembly applications. The FlexPower Pulse Tools provide operators with an industry leading power-to-weight ratio, allowing for a smaller tool selection for greater torques giving operators a lighter tool with more torque capability. Ergonomically safer than harmful hammering and vibration of impact wrenches. Built for durability with a superior O-ring design and specially designed pulse fluid FlexPower extends life between regular oil changes and provides more torque stability. Low noise decibels, minimal vibration and low torque reaction. It is important to understand your joint application before a selecting a pulse tool.
-
product
UV Fluorescence Sulfur Dioxide Analyzer
Model T100
The Model T100 uses the proven UV fluorescence principle, coupled with a state of the art user interface to provide easy, accurate, and dependable measurements of low level SO2.Exceptional stability is achieved with the use of an optical shutter to compensate for PMT drift and a reference detector to correct for changes in UV lamp intensity. A hydrocarbon ‘kicker’ and advanced optical design combine to prevent inaccuracies due to interferents.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel using NumaView™ Software, or via RS232, Ethernet, or USB com ports, either locally or by remote connection using the included NumaView™ Remote PC Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.The Model T100 comes with NumaView ™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView ™ Software.
-
product
Ultra-High Stability DC Power Supply
62075H-30N
The 62075H-30N output power has maximum 7.5kW/30V/250A power module designed with 4U height that can be connected easily as master or slave with three units to 22.5kW/30V/750A in parallel or two units to 15kW/60V/250A in series and operated as a standalone unit via system bus. The 62075H-30N provides stable DC output cur rent sour ce and powe r for pre c i s ion measurement. It offers an advanced 250A/30V ultra high-stable ±10 ppm (current stability ±1.25 mA) with high eciency and high power factor in compliance with energy savings. In addition it has a 20 bit digital control with bright vacuum fluorescent display readout.
-
product
Picosecond-Diode Lasers for Spectroscopy
Designed and manufactured by Becker & Hickl – bh delivers prominent picosecond diode lasers with wavelengths from the NUV to the NIR. All bh pulsed diode lasers work with simple +12V power supply or pull their power from the USB port of a PC or Notebook Computer. Other features are high repetition rate, short pulse width, unprecedented timing and power stability, and extremely low electrical noise level.
-
product
High Power Digital Lab Series Regulated DC Power Supply – 2KW
- 2000W different combination- High current density.- 19″ rack adaptable -3U high- Front panel potentiometer to set V&I- Remote sensing- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
product
Test Contactor
cDragon
cDragon™ Test Contactor pin’s thermal design supports fast temperature control response and stabilization for repeatable at temperature testing of devices in a handler environment.The homogenous MEMS elastomer-free multi-beam pin delivers long life and high wear resistance. By design the cDragon’s pin decouples insertion motion from the test-interface-board side of the pin. This eliminates test-interface-board pad wear.
-
product
Light Source
FiberPal OT-3000
The OT-3220/3221 is designed for a high performance stabilized laser source, especially in practice for FTTX networking installation and maintenance fieldworks environment requirements. It is usually applied as stable laser sources for wide range of optical testers and tools in optical fiber cabling and transmission systems.
-
product
PNA Microwave Network Analyzer
N5222B
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Mass Flow Controller for Medium Flow
HFM-205 / HFC-207
The HFM-205/HFC-207, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-205 / HFC-207 meters and controllers have flow ranges from 0-1000 slm to flows of 0-2500 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a full complement of fitting and elastomer options, the HFM-205/ HFC-207 covers a wide range of high flow applications.
-
product
Duct Mount Temperature/Humidity Sensor
ENVIROMUX-STHS-DCT
Combines excellent stability with easy installation and reliable operation. Duct Mount ENVIROMUX-STHS-DCT: Applications from 14 to 140°F (-10 to 60°C). Temperature accurate to within ±0.54°F (±0.3°C). Relative Humidity accurate to better than ±3% from 10 to 90% relative humidity at 68°F (20°C). Insensitive to dust and most chemicals. Requires the ENVIROMUX-S420MA-24V to operate. Maximum cable length: 500 ft (152m). Regulatory Approvals: CE, RoHS. Enclosure: IP65, NEMA 4.
-
product
Level Transmitter (Immersion)
LS
● Outer diameter Φ 28 stainless steel shell, rugged exterior is easy to install● 3 sealing process, rigorous and reliable sealing● High accuracy, high stability, low cost● Signal isolation amplifier, anti-jamming● PTFE breathable cable
