Filter Results By:
Products
Applications
Manufacturers
Probing Stations
System to contact DUTs to drive and receive signals.
See Also: Probing, Probers, Nano Probes
-
product
Electrical Probe Systems
INSTEC's Probe Systems offer an integrated solution for performing component-level electrical measurements over a wide temperature range.Compact Mini Probe Stages enable an existing inspection microscope or optical test setup to be converted easily into a precision temperature-controlled semiconductor testing and qualification station.Analytical probe stations are fully featured industry-standard platforms for all modern probing applications and testing.Benchtop Probe Stations provide the user with four independent electrical probes with X,Y,Z micropositioning for precise placement without opening the sample chamber.Highly configurable probe systems meet a range of requirements for atmospheric and temperature control, sample areas, and electrical measurements.
-
product
Semi-Automated Probe Stations
SPS 2600, SPS 2800, and SPS 12000 Series
The SPS 2600, SPS 2800, and SPS 12000 Series systems are MicroXact’s semi-automated probe stations designed to be flexible and easy to use when performing high productivity device characterization, wafer level reliability testing and failure analysis. These semi-automatic probe station systems are designed to support manual and semi-automatic probing of up to 200mm wafers.
-
product
Standard Probe Station Chucks & Accessories
In this test solutions section of our website we describe the expanding line of Abet PV IV probe stations for the growing variety of solar cell types and sizes being developed around the world. This page describes a line of vacuum chucks and accessories for top/bottom, top/top, and bottom/bottom solar cells from 3 x 3 mm to 300 x 300 mm. Probe stations for multiple device on a single substrate and multifunction probe stations are described further in the sections highlighted to the left of this page.
-
product
Semi-automatic 150mm Probe Station
CM460
CM460 Semi-automatic 150mm probe station step & repeat, point & shoot, color mapping, and complete software control.
-
product
Microscope Spectrophotometer
508 PV
The 508 PV™ Microscope Spectrophotometer is designed to add spectroscopy, color imaging, thin film thickness measurement and colorimetry capabilities to your optical microscope or probe station. It can also be used to upgrade an older microspectrometer with cutting edge optics, electronics and software.
-
product
Lab Assistant
The SemiProbe Lab Assistant family of probe stations is specifically designed to address the requirements of universities and research personnel. Lab Assistant probe stations provide simplicity, ease of operation, portability, affordability and modularity. Lab Assistant probe stations can be configured for DC or HF/Microwave testing configurations, including an array of sophisticated accessories that are usually only found on much larger, more expensive probing stations.
-
product
Stimulus Induced Fault Testing
SIFT
SIFT allows for the analysis of numerous stimuli to identify speed, fault, and parametric differences in silicon. The heart of the SIFT technique revolves around intentionally disturbing devices with external stimuli and comparing the test criteria to reference parts or timing/voltage sensitivities. Synchronous interfacing is possible to any tester without any wiring or program changes. The system can be based on either a motorized probe station or portable microscope stand for test head applications.
-
product
Portable Manual Probing Station
Model W4.0 x L6.5
This portable manual probing station is designed for a versatile, comfortable, and accurate operation on up to 4.0” wafers or 4.0” X 6.5” printed circuit board assemblies. This turn-key, manually operated probing station, model W4.0 x L6.5, is part of the D-COAX commitment to the test and measurement and PCB fabrication industries.
-
product
TDR Probe
TDP Blade Probe
The TDP Blade Probe enables fast and convenient TDR measurements and debugging. The BladeProbe tips are made from strong and rigid beryllium copper blades for handheld and probe station probing. The passive probe can be used to measure impedance, clock jitters, and skews. The TDP BladeProbe series can be connected to TDR, high performance scopes, and vector network analyzers.
-
product
Controlled Environment Probe Station
CG-196
Everbeing controlled environment probe station allows vacuum and cryogenic probing down to 77K with liquid nitrogen or high temperature probing up to 1273K. Efficient in characterizing your devices at extreme temperatures, vacuum, specific gas, etc.
-
product
Probe Station
EPS500
Reasonable price and compact design. - Sellectable chuck size : 4inch, 6inch, 8inch when ordering probe station. - Hot chuck can be installed. Temp range: RT ~ 300°C - Hot and cool chuck from 0 °C ~ 300 °C can be provided. - Maximum 6pcs of manipulators can be installed on the base unit of probe station EPS500.
-
product
Powerful, Fully Integrated Workstation for Emission Microscopy
PEM-1000
The PEM-1000 emission microscope incorporates the latest technology in real time, high quantum efficiency, mega-pixel CCD detectors in a back-thinned cooled camera. A portable system, the PEM 1000 can interface with all analytical probe stations, ATE (automated test equipment) and bench top configurations for high speed functional testing.
-
product
Semi-Automatic LCD Probe Station/Laser Repair System
LCD 2424
The Model 2424 Semi-Automatic LCD Probe Station is designed especially for probing LCDs and other large substrates. Built on a steady and reliable anti-vibration table, the Model 2424 has powerfully built features that perform a number of specific tests required by all LCD/flat panel display manufacturers.
-
product
Electro Optical Terahertz Pulse Reflectometry
EOTPR 3000
The EOTPR 3000 system is configured with a manual probe station to meet today’s tough FA environment which requires to isolate fault location in minutes rather than hours or days, while maintaining the EOTPR’s world leading sub-5 μm fault isolation accuracy.
-
product
Optoelectronics and Photonics
SemiProbe has developed probe stations for a wide variety of optoelectronic and photonic device applications, including light emitting diodes (LEDs), vertical cavity surface emitting lasers (VCSEL) and photo diodes. Testing and handling small, fragile, thin wafers with thousands of die on them poses unique challenges that require innovative solutions.
-
product
Probe Systems
These flexible probe stations are designed for the ever-changing test configurations required in a engineering lab. Combined with durable probes or your own high-speed probes, PacketMicro probe stations are the most cost-effective probing solutions in the industry.
-
product
Complete Probe Station
BD Series
Best for DC and RF probing, the platen lift is designed for smooth raise and contact of your probes simultaneously to your device. It is ideal for probing multiple spots on your device, or through multiple devices.
-
product
Analytical Probe Station with Laser Cutting System
LCS- 4000 Series
The LCS-4000 Probe Station with Integrated Laser Cutting System gives the user maximum flexibility in semiconductor diagnostic cutting, failure analysis, trimming, marking and topside layer removal. All of these functions can be performed on a microscopic level, all on this one system which provides a high level of performance that is remarkably easy to use.
-
product
Vector Network Analyzer Extenders
VNAX
VDI''s VNA Extenders deliver high performance network analyzer frequency extension into the THz range. Models cover 50 GHz to 1,100GHz with additional bands in development. VDI modules come in a variety of form factors and configurations including our original Standard-size Modules and new Mini Modules that reduce volume up to 75%. In addition to our full Transceiver (TxRx) modules, VDI also offers Transmit-Reference (TxRef) modules and Receive only (Rx) modules that deliver optimized performance for specific applications. These modules combine high test port power and exceptional dynamic range to deliver industry leading performance. They are compatible with most network analyzers and can be integrated into probe stations and antenna chambers.
-
product
Cryogenic Probe Station
CRX-4K
Designed for versatility and high performance, the CRX-4K is our premium cryogen-free closed-cycle refrigerant probe station. This system is the solution for those looking for the convenience of cryogen-free operation and the exceptional measurement performance of a Lake Shore product.
-
product
Probe Cards
PICOPROBE® PROBE CARDS by GGB Industries, Inc., allows for more chip design flexibility because each probe card is custom configured to your circuit for testing wafers on either manual or automatic probe stations. Probe cards with complex layouts consisting of numerous DC contacts and multiple microwave probes with operating frequencies of 40, 50, 67, or 110 GHz can be custom fabricated quickly and inexpensively.
-
product
CC-TLP Probe
CC-TLP-50-A1
High Power Pulse Instruments GmbH
*Capacitively coupled TLP probearm (CC-TLP) compatible with standard probing stations*18 GHz SMA connector*Tilt angle adjustment*Calibration gauge for needle height
-
product
Cryogenic Probe Station
EMPX-HF
The Lake Shore EMPX-H2 probe station enhances standard probe station capabilities with the addition of a ±0.6 T horizontal field electromagnet. All standard C-V, I-V, microwave, and electro-optical probing, plus in-plane horizontal field electromagnetic measurements can be performed on this versatile station. Researchers can use it for testing magneto-transport parameters. The EMPX‑H2 is Lake Shore’s premier probe station for vector-dependent magneto-transport measurements.
-
product
Probe Stations
PSI's 600LS Series Probe Station is designed to exceed performance metrics of equipment priced significantly higher.
-
product
Wafer Test Solutions
Wafer Test Solutions has established leadership positions in developing and deploying application-specific test solutions for MEMS devices, offering wafer and frame probing stations suitable for R&D, Wafer Sort, and Final Test. We offer state-of-the-art solutions to test environmental and motion sensors in wafer and other advanced packages.
-
product
Sealing Kit for PHD-4001A on Cascade Elite E300, Octagon CM300 Probe Station
PHD-4001-TH-Seal
High Power Pulse Instruments GmbH
*Sealing Kit for PHD-PPM10-H9 and PHD-4001A on Cascade Octagon CM300 probe station*High temperature range -40 °C to +200 °C
-
product
Mini Probe Station
C-2
The smallest probe station which still preserves the key functions and precision that are fundamental to all probing. This size is still capable of DC and RF measurements, making it the most versatile in its size.
-
product
Cryogenic Probe Station
TTPX
The TTPX probe station is an affordable, entry-level probe station capable of making a wide variety of non-destructive, standard electrical device measurements. The compact tabletop design is perfect for academic and laboratory research settings. The TTPX provides efficient cryogenic temperature operation and control with a continuous refrigeration system using either liquid helium or liquid nitrogen.
-
product
Flying Probe Programming & Test Development
Testing House offers full Flying Probe Programming and Test Development using its very own Seica Pilot LX Flying Probe Test Stations.
-
product
High Power Devices
SemiProbe configures our PS4L Adaptive Architecture into the Voltarus (TM) family of probe stations to fulfill the unique requirements of testing high power devices at wafer level prior to packaging. Voltarus probe stations are available in manual, semiautomatic, and fully automatic configurations that can test and characterize power devices up to 10 KV or 200 Amps (pulsed).
