Protocol Simulation
-
product
Voltage Dip & Swell Simulators
VDS Series
A simulator to reproduce voltage variation phenomena in commercial power supplies (AC100V/200V).This type of immunity test against voltage variation phenomena is defined in IEC 61000-4-11 and is widely used in many industries.
-
product
Light Simulator
From the review of the scientific development history, reliable and stable artificial light sources have played a very important role in the past century. For example, the artificial solar simulator is an important part of simulating sunlight to ensure accurate performance of PV characterization. With the growth of light sensor applications, more and more requirement of light simulators (or artificial light sources) explored. One of the core technologies of Enlitech is the artificial light sources. We can manipulate different lamp types (short arc lamps, LEDs, filament lamps et. al.) to generate different spectrum-form in different light intensity levels, beam sizes, and wavelength ranges. We have launched different artificial light source products for different applications fields. For instance, SS-X series solar simulators and ILS-30 ambient light simulator are for the PV field, HAAS is highly accurate star light simulator for the space field, and ALS-300 is a general-purpose light source in science research field. These products can not only meet the needs of your application, but also speed up the process of your research or mass-production.
-
product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
product
Protocol Converter
MACC
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
product
Reflow Simulator
SRS-1C
Reproduce the temperature profile of Reflow oven. Can observe the melting state of solder paste.
-
product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
product
8 Port Phone Line Simulator (FXS) Adv
CH-8FXS-A
This unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
product
SAS Protocol Test System
M124A
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
product
BusFinder Protocol and Logic Analyzer
Acute BF7264B+
*Two-in-One Analyzer (Protocol and Logic)*PC-based, 64 channels*USB 3.0 interface, 12V power adapter*32Gb total memory*NOW supporting MIPI D-PHY 1.2 (includes MIPI CSI)*NOW UFS2.1 supported with new BF7264B+
-
product
Testing And Simulation
Uni- and bidirectional power supplies for testing and simulating batteries, fuel cells, electric drive trains and other components.
-
product
BACnet Packet Capture And Protocol Analyzer For MS/TP
BACTrace
The multi-pane user interface shows captured packets in several different kinds of detail. The upper pane displays a quick summary of received packets, each of which is identified by number. The MS/TP frame type, destination and source MAC addresses are shown, as well as a timestamp in milliseconds. For APDUs, the BACnet service is also shown.
-
product
PathWave IC-CAP Simulation and Analysis
W7010E
The W7010E PathWave IC-CAP Simulation and Analysis add-on enables simulation, tuning, and optimization of device behavior using Keysight's PathWave Advanced Design System (ADS) or the provided SPICE3 simulator or by linking directly to supported external simulators.
-
product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
PCI Express (PCIe) 5.0 and Compute Express Link (CXL) Protocol Analyze
Your product description goes here.
-
product
Engine Torque Pulse Simulation
ETPS
HORIBA has revolutionized the way vehicle manufacturers test their Powertrains and Front End Accessory Devices. The ETPS dynamometer system accurately produces torsional pulse characteristics of an engine. This new technology employs a sophisticated mathematical model to calculate the resulting torque at the output of the engine based on engine and combustion process parameters.
-
product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
product
PXI/PXIe Battery Simulator Module, 4-Channel With V/I Readback
41-752A-012
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
2 PRI + 16 BRI-S/T ISDN Simulator
CH-16BRI-ST-MOD-2PRI
This unit has two PRI ports and 16 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
product
ARINC 429 USB & LAN Test & Simulation Module
UXI-429
Avionics Interface Technologies
8 Channel (4Tx/4Rx) & 16 Channel (8 Tx/8 Rx) models available - Programmable Tx channel output amplitude - Programmable high/low speed operation - Concurrent operation of all Tx/Rx channels at high speed rates - Full error injection & detection - Rate-oriented label transmission - Label selective trigger for capture/filtering - Real-time recording & post analysis of multiple channels - Physical Bus Replay - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs)
-
product
HDMI 300MHz Protocol Analyzer
VA-1838
Testing HDMI 4Kx2K timings, 3D, ARC, CEC, HDCP function.
-
product
Radio Link Simulator
RLS-2100
Square Peg Communications Inc.
It is the most comprehensive, with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full motion support and integrated GPS simulators. It is the most flexible, providing end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. It supports the highest bandwidth and has an intuitive, user-friendly interface. And it does it all in one box.
-
product
MIMIC® Redfish Simulator
The MIMIC Redfish Simulator, the industry's first integrated simulation tool supporting Redfish, allows developers to perform real world, integrated device simulations. MIMIC simulates thousands of Redfish-capable devices. MIMIC allows suppliers of Redfish devices and applications to design, develop and test their products in a virtual and scalable network environment, assuring customers that their applications will be able to handle the scales of messages and different types of requests to work properly when deployed across heterogeneous environments.
-
product
Simulation Environments Software
Modelica
Modelica Libraries with a large set of models are available (overview, details and download). Especially, the open source Modelica Standard Library contains about 1280 model components and 910 functions from many domains.
-
-
product
Automotive Protocol Decode/Trigger Software (CAN, CAN FD, CAN XL, LIN FlexRay, SENT) for Infiniium Oscilloscopes
D9010AUTP
- Set up your scope to show CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT protocol decode in less than 30 seconds- Support CAN XL protocol trigger and decode of the SIC mode (or slow mode) signal in the arbitration phase as well as the FAST mode signal in the data phase- Get access to a rich set of integrated software-based protocol-level triggers- Save time and eliminate errors by viewing packets at the protocol level- Use time-correlated views to quickly troubleshoot serial protocol problems back to their timing or signal integrity root causeThis application (for Infiniium Oscilloscopes) includes a suite of configurable protocol-level trigger conditions specific to CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT. When serial triggering is selected, the application enables software-based triggering. Application supports CAN-dbc symbolic debug.
-
product
Patterning Simulation
KLA’s patterning simulation systems use advanced models to explore critical-feature designs, manufacturability and process-limited yield of proposed lithography and patterning technologies. Our patterning simulation software allows researchers to evaluate advanced patterning technologies, such as EUV lithography and multiple patterning techniques, without the time and expense of printing hundreds of test wafers using experimental materials and prototype process equipment.
-
product
PCI Express 5.0 Protocol Exerciser/Analyzer
Summit Z58
The Summit Z58 is a PCIe 5.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z58 can emulate PCI Express 5.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
product
GNSS Testing & Simulation
Safran Federal Systems is a leading provider of advanced GNSS Testing & Simulation systems and tools for NAVWAR environments.
-
product
Electromagnetic Simulation Software Suite
EMTOOLS
EMTOOLS is a computational electromagnetic (CEM) software suite comprised of 16 different software codes. ACAL (Advanced Complex Algebra Library) is an out-of-core linear system solution library, using a hyper-matrix approach to partition the problem. The AntFarm™ (Antenna Farm) toolkit analyzes the radiation and electromagnetic interference (EMI) effects of single or multiple heterogeneous RF systems. Apatch™ software is an antenna design and analysis tool that provides antenna simulation and modeling by computing the radiation and receiving pattern of an antenna or antenna array installed in an operational environment...
