High Voltage Transformers
See Also: Substation
-
Product
AC Voltage Sensors
-
Continuously monitor single or three-phase power lines for over or under voltage conditions with DARE?s AC voltage sensors, voltage monitors, and voltage sensing relays. DARE?s complete line of AC Voltage Sensors will protect system equipment and circuitry from voltage that is hazardous or unsuitable for operation.
-
Product
High Voltage Tester For Hair Dryer & Hair Straightner
-
Every electrical apparatus or machine consists of two distinct sections - one which carries the electricity, and other which is isolated (insulated) from the electric currents. The former may be called the `Live' side whiles the latter `Earth’ side. A person near about the apparatus or handling it can safely touch the Earth side, but not the live side, for obvious reasons. To ensure that the isolation of the two sections is effected properly, the apparatus is tested by subjecting it to a Voltage much higher than the normal working Voltage. If the insulation is good, it stands the test without breakdown otherwise high electrical stress punctures the insulation at its weakest spot foretelling a later calamity to unwary user. Government Department- when buying electrical equipments- and all reputable manufacturers test every piece of equipment by this test called HIGH VOLTAGE TEST. It weeds out poorly insulate apparatus.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-010-HI
Programmable Resistor Module
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Current Transformers
Sensors
-
The Current Transformer (CT) is the sensor which measures the amount of current draw from the wire it is installed on.
-
Product
Solid State Active Synchro Control transformer and Solid State Resolver Control Transformer
-
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems. They simultaneously accept a 3 wire synchro input (0) and a digital angle input (0), and provide an ouput which is the sine of the difference between these two input angles (A sin wt sin (0-0) ("wt" is the synchro excitation frequency).
-
Product
PXI High Voltage Power Multiplexer, Dual 12:1
40-331A-002
Multiplexer Module
The 40-331A-002 dual 12:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
Transformer Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
Your product description goes here.
-
Product
HIGH VOLTAGE MEGOHMMETER
MI-20KVe
-
The MI-20KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 20 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 4.000.000 MΩ with four test voltages: 5 kV - 10 kV - 15 kV and 20 kV. Readings are performed through an easy-to-read analogue indicator, having a broad scale.
-
Product
High Voltage 37 Pin D-Type Cables - Connector to Unterminated for Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 37-pin D-type connector.
-
Product
T3 Low & High Voltage Differential Probes
T3 Series
-
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
Product
Additional Products: High Voltage 37 Pin D-Type Cables - Connector to Unterminated
Cable Assembly
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Impulse Voltage Generator
-
Shanghai Sanki Electronic Industries Co., Ltd.
Impulse voltage generator Impulse voltage generator is mainly used for test products such as power equipment to perform lightning impulse voltage full wave, lightning impulse voltage chopping, operating impulse voltage wave and steep wave impulse voltage test, to inspect insulation performance. The technical indicators comply with national standards and IEC standards.
-
Product
High Voltage 37 Pin D-Type Cables - Connector to Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 37-pin D-type connector.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-326-HI
Programmable Resistor Module
The 40-230-326-HI (PXI) and 42-230-326-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 26.7kΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Transformer Preamplifier
SR554
-
Stanford Research Systems, Inc.
The SR554 is a low-noise, transformer-coupled preamplifier optimized for source impedances between 0.05 Ω and 1 kΩ. With an input noise of only 0.1 nV/√Hz, the SR554 can be used in a wide range of low-noise applications.
-
Product
Voltage logger0 to 25V
TK-4702
-
Supplied with an input cable, this logger can measure voltages up to 25V DC and can be connected to many industry standard devices, such as CO2 sensors and current clamps, enabling the logging of a wide range of process parameters.
-
Product
Micropower Voltage References
-
Analog Devices offers a broad line precision micropower voltage references with extremely low quiescent currents (series references) or minimum shunt currents (shunt voltage references). All of our precision voltage references offer excellent initial accuracy and low temperature drift over time and temperature. Our Reference Plus products combine precision voltage references with comparators or amplifiers.
-
Product
Auxiliary Potential Transformers
-
Osborne Auxiliary Potential Transformers (Aux PT’s) are used in utility and commercial industrial power systems. Osborne works with our clients to identify the safety advantages of using auxiliary potential transformers (Aux PT’s) to establish protection schemes for high voltage equipment. Aux PT’s step the voltage down to safer levels, normally below 600 V AC.
-
Product
Ultra Light High Voltage DC Test Sets
-
This Compact power supply/test set can perform all laboratory and field tests of DC Hipot. A flexible High Voltage Cable is provided at the back for connecting to the test specimen. Available in Rack Mount as well as portable design.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-256-HI
Programmable Resistor Module
The 40-230-256-HI (PXI) and 42-230-256-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 76.8MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe High Voltage Multiplexer, Triple 7-Channel, 2-Pole
42-321-122-HI
Multiplexer Module
The 40-321-122-HI (PXI) and 42-321-122-HI (PXIe) are triple 7-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI 18xSPST High Voltage Power Relay Module
40-330-002
Relay
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-225-HI
Programmable Resistor Module
The 40-230-225-HI (PXI) and 42-230-225-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-121-HI
Programmable Resistor Module
The 40-230-121-HI (PXI) and 42-230-121-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 925Ω with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Transformer Short Circuit Impedance Tester
JYW6300
-
This instrument is mainly applicable to low voltage load impedance test of 35kV and above power main transformers (single phase or three phases) in ex-works routine tests, overhaul tests, pre-tests, and acceptance tests.
-
Product
Voltage Detector
KEW 5711
-
Kyoritsu Electrical Instruments Works, Ltd.
Senses AC voltage through insulation. Buzzer sounds and tip glows upon ac voltage detection. Powerful flashlight. Dual range (Hi/ Lo) sensitivity. Ready to use without power-on. Designed to meet IEC61010-1.
-
Product
Voltage Pulse Generator
LSG-65C
-
Shanghai Sanki Electronic Industries Co., Ltd.
The waveform parameters of the voltage pulse generator LSG-65C fully meet the requirements of IEC60065 and GB8898; the pulse voltage output of up to 10kV can meet the requirements of different test levels of users; the self-developed high-voltage electronic switch is adopted , which has high stability, low noise and long service life. Long; digital display mode, intuitive and easy to operate.
-
Product
Precision Multirange Voltage Transformers
WP-36000
-
The WP-36000 Transformer is primarily a laboratory standard. The high degree of accuracy and multiplicity of ranges makes this transformer the standard for precision calibration work. With the aid of this transformer, very accurate determination can be made of the ratio and phase angle characteristics of voltage transformers having ratings from 14,400 to 36,000 volts.
-
Product
Voltage And Continuity Testers
-
Unlike voltage testers, continuity testers are always used when a circuit is turned off—or on wiring or devices that are disconnected from the circuit. They don't test for the presence of voltage but rather to see whether an electrical path is intact in an appliance or a device.
-
Product
Injection Transformer
J2100A
-
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
