DTV Monitoring
-
product
Linear Polarization Resistance (LPR) Monitoring
The electrochemical technique, commonly referred to as Linear Polarization Resistance, is the only corrosion monitoring method that allows corrosion rates to be measured directly, in real time. Although limited to electrolytically conducting liquids, the response time and data quality of this technique make it clearly superior, where applicable, to all other forms of corrosion monitoring.
-
product
Leakage Current Monitor
To alert utility-line workers of overcurrent conditions on such aerial devices as insulated ladders and truck booms, the Chance Sentinel sounds an alarm if leakage current reaches a pre-set level.
-
product
Explosion Proof Area Hydrogen Monitor
HY-ALERTA™ 2620
H2scan’s 2620 Explosion Proof Area Hydrogen Monitor provides hydrogen-specific leak detection and measurement for hydrogen concentrations as low as 4000 ppm and can be scaled to any concentration up to 5% hydrogen by volume, a range representing 10% to 125% of hydrogen’s low flammability limit. The monitor is designed for either ceiling or wall mount. H2scan’s hydrogen-specific sensor technology has no cross sensitivity to other combustible gases, thus eliminating false positive alarms and ensuring safety system reliability.
-
product
Multi Wavelength Monitor
LV5490/LV5480
The LV 5490 is a multi waveform monitor that supports 4K video format (4096×2160、3840×2160) based on 3G-SDI dual link or quad link, HD-SDI quad link, and 12G-SDI. The following two 4K video division transmission systems are supported. ・2-SAMPLE INTERLEAVE DIVISION ・SQUARE DIVISION
-
product
Monitoring Systems
Our bestselling Accsense Ethernet Temperature Datalogger is designed for cost-effective temperature measurement and alarm in medical refrigerators, freezers, cryogenic storage and incubators. We also provide additional models of Accsense data loggers which monitor additional values including humidity, digital, pressure, and more.
-
product
Active Network Assessment and Monitoring Platform
Hawkeye
Keysight Network Applications and Security
Network performance and user experience are critical aspects of your business. It is vital to understand customers’ perception of your website, application, and network services. NOT knowing impacts your revenue stream. Ixia’s Hawkeye continually measures network performance and service status. If there is an issue, Hawkeye helps you identify it, quantify it, and ultimately resolve it – before your customers experience it.
-
product
SpaceWire Monitors
This section details the 4Links range of high-performance test equipment that is used to monitor SpaceWire networks. These devices are attached to your SpaceWire systems and then can be accessed via Gigabit Ethernet, using the standard TCP/IP family of protocols, so that they can be controlled remotely (for instance, by partners collaborating on a mission).
-
product
Survey Solution for Monitoring
TideStation – Portable
A portable survey solution for monitoring of Tide, Met and other sensors, the TideStation Portable is housed in a large, rugged ABS case.
-
product
CMAS Analyzers and Field Monitors
Backed by at least one of the 8 corrosion sensor patents wholly owned by Corr Instruments, our nanoCorr analyzers and field monitors are widely used for online and real-time localized and general corrosion monitoring. These ultra-high precision instruments measure extremely low currents in the pico-ampere levels, which can be translated into a corrosion rate as low as a few nanometers per year, in some applications (PDF). Our analyzers and monitors are based on the patented coupled multielectrode array sensor (CMAS) technology which measures the flow of electrons from corroding electrodes to one or more cathodes.
-
product
Control & Monitoring
Omega has a large selection of control and monitoring devices to chose from. Omega devices can measure anything from gas, liquid, or temperature to process voltages and currents, and much more!
-
product
Compact Data Logger: Monitoring Temperature, RH and Dew Point
HD208
The data loggers of the series HD208 are compact instruments for monitoring temperature, relative humidity (RH) and dew point temperature. Usable in a wide spectrum of applications, are available in various models (with or without LCD display):
-
product
Continuous Monitoring System
viewLinc
The Vaisala continuous monitoring system is ideal for both light and heavy industrial environments, as well as GxP-regulated applications, the system integrates a wide selection of data loggers, transmitters and Modbus devices to monitor several parameters: temperature, relative humidity, dew point temperature, CO2, differential pressure, door contacts, and more.
-
product
Circuit Monitor
CM, CMD
*Continuous monitoring of trip coil continuity*LED indication of open trip circuits*N.O. or N.C. contact for remote indication of open trip coils.*Self-monitoring — long-life*Can also be used as a self-latching, high speed target for trip indication*UL Recognized*RoHS Compliant (Directive 2002/95/EC)
-
product
Spectrum Monitoring Systems
RFeye®
The product range includes entry level systems for dense network deployments through to best-in-class systems for military applications. RFeye Nodes are recognized as the "industry standard" for fixed remote distributed monitoring. In addition, we supply portable and vehicle based systems and a range of RFeye Arrays that are an extremely cost-effective alternative to traditional direction finders
-
product
Acoustic Wave (Acoustic Emission) Monitoring Solutions
Qingcheng offers a variety of solutions to solve some essential difficulties and problems in some industrial fields.
-
product
Respiration Monitor Belt Logger Sensor
NUL-236
This sensor comes with a belt and measures the air pressure in it. The pressure changes according to the breathing of the subject. From the measured values, the respiration rate can be calculated.
-
product
Storage Resource Monitor
Storage resource management reporting for health, performance, and capacity of multi-vendor storage
-
product
Air Gap Monitoring & Analysis
Solutions for air gap monitoring in order to plan maintenance prior to reduced operating efficiency or damage from magnetically induced heating or rubbing between the rotor and stator.
-
product
PXI Monitored Multiplexer, Quad 16-Channel, 1-Pole
40-619-004
The 40-619-004 is a high density PXI 2 A multiplexer module in quad 16-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
-
product
Water Quality Monitoring System
WQMS
Water Quality Monitoring System (WQMS) is a facility to measure pollutants such as Chemical Oxygen Demand (COD), Total Phosphates (TP), Total Nitrogen (TN) etc. The required parameters are customized according to the type of factory and discharge regulations.
-
product
Remote Corrosion Monitoring
Telemetry System
Metal Samples’ remote telemetry system obtains real-time corrosion monitoring data via the Internet from anywhere in the world. The system features communications via satellite to a secure Web Monitor data server. With this powerful web-based back end, you can bring the data to your desk no matter where the site is located.
-
product
Medical Monitors
Advantech develops three types of medical monitors (PAX Series), including surgical, diagnostic, and clinical monitors.
-
product
High Voltage Surge Current Monitors
HVSCM
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
product
Aerosol Monitor
DUSTTRAK II-8530
The DUSTTRAK™ II Aerosol Monitor 8530 is a desktop battery-operated, data-logging, light-scattering laser photometer that gives you real-time aerosol mass readings. It uses a sheath air system that isolates the aerosol in the optics chamber to keep the optics clean for improved reliability and low maintenance.
-
product
3 Phase Power Monitors
The PM7000 portable monitor, the PM7503 panel mounted monitor and the PM7000 Fault Level Monitor have 4 current inputs and 4 voltage inputs while the PM3000 portable monitor has 3 current and 3 voltage inputs. All 4 different models record data using our patented Single Cycle Adaptive Store recording regime whereas the PM7000, PM7503 and PM7000FLM also have 3 other unique and distinct recording regimes:
-
product
Surveillance Monitor
SMARTS II
*Real time frequency response evaluation*Audible and visible alarms*Remote monitoring*User settable alarm thresholds
-
product
Condition Monitoring Solutions
VibroLine
The VibroLine devices are stationary analysis modules for continuous condition monitoring on machines and systems. The VibroLine condition monitoring system can be used to monitor vibration acceleration, speed or displacement with freely adjustable frequency filtering for different applications. Permanent vibration monitoring of your machines not only brings competitive advantages through the increased efficiency of your systems, but also protects against unwanted machine failures. With the VibroLine devices, you can monitor not only the sum, order and storage characteristics, but also impact characteristics. This offers you enormous flexibility in terms of monitoring parameters for your condition monitoring.
-
product
Fixed Aperture RF Current Monitoring Probe
TBCP1-200
The TBCP1-200 is a fixed aperture RF current monitoring probe.The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.
-
product
Continuous Emissions Monitoring
atmosFIR CEM
atmosFIR CEM is a complete emissions monitoring system incorporating the atmosFIR 19” FTIR analyser. As completely hot and wet emissions measurement, atmosFIR CEM is ideal for complete measurement of multiple gases from applications such as incineration and power. A standard gas suite of NO, NO2, N2O, SO2, NH3, HCl, CH4, O2, CO2 and H2O is provided, but with the powerful FTIR analyser, further gases can be added easily in software.
