Filter Results By:
Products
Applications
Manufacturers
Continuity Testers
Verify circuits by providing an audible or visible indication when a sufficiently low resistance is applied between input probes.
- CAMI Research Inc.
product
Guided Assembly | Cable Harness Testers
Autobuild™ Software
Our optional, add-on AutoBuild™ software (Item 728) offers Guided Assembly for cables and wire harnesses. Use a supplied probe, or a finger with wrist strap, to touch an unterminated wire and the software shows (and says) exactly where the wire should be connected. As the operator attaches each new wire, AutoBuild checks the entire assembly and provides a clear checklist showing all completed good connections. When using our resistance-capable testers, you may connect diodes and resistors by name and value, check resistance values over the tester's specified range, and test conduction and isolation resistance against specified thresholds. Programmable tones accompany the graphic screen to give clear signals to the operator when good connections are completed or when incorrect connections, resistance violations, or diode insertions are detected. Combine with our Light Director™ option for light-guided assembly.
-
product
Continuity Tester
TE6-0711
Hangzhou Tonny Electric & Tools Co., Ltd.
*Designed to test circuits while power is off*2 AAA batteries included*Durable ABS housing*36" Test lead with insulated alligator clip*Sharp tip for probing circuits
-
product
Installation Tester
M72
Multifunction installation tester for insulation measurement up to 500V, continuity of protective conductors, phase sequence with TRMS multimeter functions.
-
product
Wristat Tester
WT 25-4145.26M
WT 25-4145.26M Wristat Tester is available to comply with D.O.D. 4145.26 specifications. The WT25-4145.26M Wristat Tester is designed to test the integrity of our WRISTAT in a fast, efficient, and simple manner. All the elements of the WRISTAT – continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact – are easily confirmed by pressing the top cover of the WT25-4145.26M. The operator (wearer) is tested for a resistance to ground of greater than 250K ohms and less than1,200,000 ohms. The upper limit notifies you of an unacceptably high resistance value (IE possible loss of effective dissipation) and the lower limit warns of unsafe low resistance (possible risk of electric shock from surrounding motors, live wires etc.). The unit is not switchable.
-
product
10A Continuity Tester
EQUITEST
EQUITEST is connected to its master unit via C2050 cable and to the mains for power supplying.Please refer to the user manual of your HT installation safety tester for the compatibility to EQUITEST.
-
product
Cable Continuity Tester, DB9, RS232 Mini, Network, 21.01 mm, 35 mm, 45.01 mm
72-9200
The 72-9200 is a Mini Cable Tester with USB Power Cable and Battery. Quickly test DB-9/RS-232 cables. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini cable tester fits easily in your pocket or tool box and requires no external power. Confirms conductor continuity with sequential LED's. Save time and money by diagnosing connectivity issues.
-
product
Bare Board Tester
1232
High-Precision Batch Fixture-Type Testing System that Support Boards with Embedded Passive and Active Devices. The 1232 is a bare board tester that utilizes the full range of Hioki’s in-circuit testing technologies to deliver LSI reliability testing, complex component separation testing, high continuity and insulation testing, and more. (Double-sided alignment) Testable board dimensions: 50 × 50 to 330 × 330 mm (including clamp area) • Support for build-up boards that require resistance guarantees.
-
product
Cable Continuity Tester, VGA/UL2919 Mini, Network, 21.01 mm, 35 mm, 45.01 mm
72-9205
Quickly test VGA / UL2919 cables No need to carry bulky, expensive cable testers to test only one or two cable types Mini cable tester fits easily in your pocket or tool box, and requires no external power Confirms conductor continuity with sequential LED's Save time and money by diagnosing connectivity issues All units are powered by a cross compatible 3xAA battery pack or USB cable (both included) Most units measure 2" x 2" x 1" or less!
-
product
Carry Case For Voltage / Continuity Testers
CP1190
Complete with belt loopSize: 290 x 75 x 45mm.
-
product
Clamp Meter
KT-266F
3 1/2 digits LCD with max. reading of 1999AC/DC voltage and Resistance measurementFrequency test50 mm Large jaw DiameterPlug - insulation tester adapter 500 VDC (optional)Audible continuity, Data hold ,Diode testLow power indication
-
product
Wire Harness Tester
NX Pro
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
product
Voltage and Continuity Testers
Amprobe voltage and continuity testers have built-in shakers for fast, easy troubleshooting with CAT IV 600V/CAT III 1000V input protection. To safely detect voltages up to 122kV without contact to the current carrying conductor, choose an Amprobe high-voltage tester. These intrinsically safe tools are ideal for industrial, utility, and mine applications.
-
product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
product
Two-Pole Voltage Tester
P-4
Sonel P-4 is reliable, particularly durable and safe 2-pole testers, which enable testing voltage, circuit continuity and phase sequence. It has been designed for use in extreme conditions both in industry and commercial applications. Advanced technology, a high level of safety and user-friendliness are the key features of the P-line voltage testers.
-
product
(PoE) Signal Tester
T015-POE
The T015-POE Network and PoE Tester consists of an emitter and a remote. Its functions include standard and non-standard PoE equipment detection, PoE power online test, network cable continuity test, DC power test and switch loopback test. It is a practical tool for technical personnel to use during installation and maintenance of security monitoring equipment, communications wiring, integrated wiring and other weak-current systems.
-
product
Network Analyzer, Tester, LED
72-9450
This cable tester allows for quick and easy troubleshooting of RJ45 and USB cables. Checks for continuity, faulty wiring, open, shorts, straight through or cross pinning of cables.
-
product
Volt Tester
VT750LCD
The VT750LCD is a compact reliable robust automatic voltage tester up to 750V. The testers can measure and indicate the exact voltage (AC/DC), phase indication, phase rotation and continuity, RCD, and resistance via an LCD.
-
product
Coaxial Cable Tester
6106
Peaceful Thriving Enterprise Co Ltd
This device is designed to test the connection of F type coaxial cable. The testing includes continuity and cable mapping. The tester includes 4 mapping terminals with different color and a F type adapter, which are very helpful for cable identification.
-
product
AC Hipot Tester
298
Our Model 298 is a simple-to-use 500VA AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 298 500VA AC Hipot Tester includes all the features you need to get the job done and move on.
-
product
Cable Tracers
162 CB
Standard Electric Works Co., Ltd
Filter Probe● Works with any Tone Generator to identify wires.● Volume control for increasing sensitivity and adjustable to suit work environment.● 2 operation modes: Filter on / Filter off.● The auto-off function (5 minutes) prevents battery consumption.● Power supply is available in any 9V battery with a life of approximately 50 hours.● A phone jack is designed for headset or handset.● Flashlight function.Tone Generator● Tone Generator is a great tool for locating and identifying cable pairs or individual conductors.● 162 CB-G doesn't only provide the function of a tone generator, but also serves as a continuity and polarity tester.● A tone selector switch located inside the unit for selection of the fast tone or the slow tone.● Two bi-colored LEDs for Line1 and Line 2 indication of the polarities of the telephone lines.● The unit has alligator type terminals, a modular cable of 4 conductors with a strong connector.● The tone and continuity functions are only applied to Line1. (Modular connector)
-
product
Electrical Test Tool
Beijing GFUVE Electronics Co.,Ltd.
Electrical testers are useful to check for voltage, continuity, shorted or open circuits, and improper wiring.
-
product
Continuity Tester
4102
Peaceful Thriving Enterprise Co Ltd
This product is designed to measure the continuity of electric circuits and components. The measurement result will be indicated by LED and buzzer. The illumination is very helpful when technician is working in dark environment.
-
product
Optical Tester
FOD 1203
The Optical Tester FOD 1203 was specifically designed for technical support personnel to take a variety of measurements with a single meter. The FOD 1203 is an updated version of a popular in the industry Optical Power Meter FOD1202 with a built-in light source at 850, 1310, or 1550 nm wavelength. This device not only measures optical power, but also attenuation and continuity in connecting cables.
-
product
Wire Harness Tester
NX Solo
The Dynalab NX Solo Wire HarnessTester is a low-cost, feature-packed, stand-alone tester with a maximum capacity of 256 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to decide which operation to perform next. Testing for continuity, shorts, and a variety of components.
-
product
Manual PAT Testers
If you are looking for a manual PAT tester with a pass fail reading or a PAT tester with readings we have a solution for you. Carry out mains supply checks, IEC lead tests, Earth continuity tests at 200mA, Insulation resistance tests to 250V and 500V, and more with these popular testers. All of our manual PAT testers are available as kits to help you streamline the way you work.
-
product
Electrical Testers & Voltage Continuity Testers
Fluke’s line of electrical testers and voltage detectors are designed for use in every application and in nearly any environment. From non-contact voltage detectors and voltage testers with continuity detectors, to open-jaw current testers and open fork testers with FieldSense® technology (for voltage and current measurements without test leads), these testers are accurate, safe and easy to use.
-
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
product
Loudspeaker Cable Testers
EMO E450
The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.
-
product
LAN Tester / Wiremap Tester & Cable Fault Locator
RapidTrace 700
Compact, Powerful and Easy to use. This high performance low cost LAN Tester / Wiremap Tester and Cable Fault Locator is the perfect tool to enable you to test and certify structured cabling continuity to TIA568A/B, USOC and ISDN standards.
-
product
Heavy-Duty Continuity Tester
TE6-0710
Hangzhou Tonny Electric & Tools Co., Ltd.
*Designed to test circuits while power is OFF*2- 1.5V Button cell batteries included. *Durable ABS housing.*High-quality materials for long-lasting durability.*Sharp tip for probing circuits.*Electrical Multi-Testers for almost any automotive repair on all 6, 12 , 24 and 48 volt systems.*Suitable for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses
-
product
Single-Functional Testers
MI 3121
The MI 3121 SMARTEC Insulation / Continuity is a tester for dead testing of electrical installations. With both an analogue and digital representation of the results, the instrument ensures accurate measurements up to 2000 Ω on continuity and up to 30 GΩ on insulation function. Configurable limits enable a PASS / FAIL evaluation of test results, which is accompanied with the bright red and green indicator lights for comfortable use even in the dark conditions. The MI 3121 is equipped with a built-in charger and has a magnetic holder in order to free up hands for testing.
