Traces Wire
Identify a wire's path.
-
product
Wiring Diagnostic System
TRACER 1.0
TRACER creates vehicle- and fault-specific diagrams on the fly. It can diagnose the probable cause of failure in a network of wiring harnesses and modules and lets technicians choose a CAD view of the wiring layout to find the precise failure location (down to a specific pin), so they can correct the issue efficiently. Tracer saves labor costs, overhead costs and helps avoid collateral damage. TRACER streamlines ELT and dealership repair. It's helpful for all vehicles, particularly new models, where technicians lack the familiarity to assess and resolve electrical issues in a timely manner. TRACER also makes aberrant anomalies a thing of the past—when a vehicle rolls down the line with a never-before-seen combination of electrical failures, resolution becomes a matter of routine. TRACER dramatically reduces effort and increases efficiency.
-
product
Trace Oxygen Analyzers
Alpha Omega Instruments trace oxygen analyzers and transmitters incorporate an advanced electrochemical sensor that provides exceptional life, accuracy, and stability. Alpha Omega Instruments electrochemical sensors provide as much as three times the life of conventional “fuel cell” type sensors. And, if you are looking to measure from parts per billion to 100%, Alpha Omega Instruments offers a high-performance zirconium oxide oxygen sensor.
-
product
5 Micron Wire Grid Polarizer
These wire grid polarizers are fabricated from 5 micron diameter tungsten wire, and have a choice of wire spacing down to 12.5 microns. They are suitable for use from approximately 50 microns (or 6 THz) to longer wavelengths. Please refer to the table below for the standard availability of wire spacing and frame clear aperture / outer diameter.
-
product
Glow Wire Tester
TF346
TESTEX Testing Equipment Systems Ltd.
Glow Wire Tester, to determine the resistance to fire insulating parts. The testing of electro-technical products for fire hazard is conducted by simulating as closely as possible actual effects occurring in practice. Parts of electro-technical equipment which may be exposed to thermal stress due to electric effects & deterioration of which may impair safety of equipment shall not be unduly affected by heat & fire generated within the equipment.
-
product
Glow Wire Tester
Shanghai Dean Electrical Co., Ltd
Glow wire tester would stipulate material (Ni80 / Cr20) and the shape of the heating wire (4 mm Φ nichrome wire) in large current heated to test temperature (550 ℃ ~ 960 ℃, after 1 mi to specified pressure (0.95 + / - 0.1 N) vertical burning hot try 30 s, inspect goods and bedding content whether light-off or the burning time to determine the fire risk of electrical and electronic equipment finished product;Determination of ignitability, ignitability temperature (GWIT), ignitability and ignitability index (GWFI) of solid insulation materials and other solid combustible materials is also applicable to the industries of insulation materials, engineering plastics or other solid combustible materials.
-
product
Cables, Harnesses & Wiring Looms
Amfax manufacture a wide range of wiring harness solutions in a variety of styles and finishes. These wiring harnesses, or looms as they are often called, can be constructed using heat-shrink, conduit tube, braid, tape, tie-wraps or lacing cord.
-
product
Underground Wire Locators
Shenzhen Noyafa Electronic CO.,LTD
Regardless of your needs, having a reliable wire locating device is critical to a successful project. Noyafa has been developing and manufacturing wire and cable locators since 2006.Our locators help in accurately locating the path of the underground wires, moreover measure the accurate depth of the invisible underground wires, and most importantly the price is affordable!
-
product
Lamp & Fixture Wiring Tester
GT3110GAM LAMPCHEK
LampChek indicates the lamp and fixture continuity.
-
product
Probes With Lead Wires
Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.
-
product
Corona Resistant Tester of Enamelled Wire
DPT-1000S
Shanghai Dean Electrical Co., Ltd
·The tester is comply with the requirements of standards GB/T 1707-2008, GB/T 24122-2009, GB14711-2013, meet the requirement of standard JB/T 10930-2010;·Multiple samples can be tested at same time;·Used for testing the feature of high frequency pulse resistance (performance of Corona-resistance).
-
product
Reverse Engineering/Circuit Tracing System
Qmax Test Technologies Pvt. Ltd.
Your product description goes here.
-
product
High Precision Glow Wire Tester
CX-Z17
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is desinged according to IEC60695-2-1, IEC60695-2-13, UL746A, IEC829, DIN695 and VDE0471 etc. standards.The IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances.
-
product
Wire Probe Needles Materials & Pin Diameters
Advanced Probing Systems, Inc.
Tungsten pins and tungsten-rhenium pins can be provided with either nickel plating or silver plating. Beryllium-copper pins are supplied with a silver plating coating.
-
product
Wire Testers
Precision Mastech Enterprises Co.
ower supply: 1*9V 6F22 BatteryProduct size: 190mm*89mm*42.5mm/7.48"*3.5"*1.67"Product weight: 420g/0.92IbSafety rating: CE(EMC+LVD) ETL CAT.III 300V RoHS
-
product
Gauge Type T Thermocouple Wire
W-TW-44TEF
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
5 KN Grips For Fine Wire
These grips offer a suitable method for tensile testing soft metal wires, ropes, and strings, all with a diameter of 3 mm (0.12 in) or less. The upper and lower grips include an articulated joint to maintain alignment of the specimen with the testing axis during testing.
-
product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
-
product
Process Trace Oxygen Analyzer
Model 3020T
Teledyne Analytical Instruments
The Model 3020T is a microprocessor-based instrument for detecting oxygen at the parts-per-million (ppm) level in a variety of gases. This instrument serves as the explosion-proof, bulkhead-mount version of the 3000 Series. Simple menu choices, externally accessible command switches, and dual LCD and LED displays make setup and operation clear and quick.
-
product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
product
Field Portable Wire Analyzer
Model 2635
The perfect tester for field use is rugged, mobile, and lightweight, without sacrificing the functionality and power of a larger system. That tester is found in the Model 2635. Weighing 32 pounds (14.5 kg), this wiring analyzer handles up to 400 test points of Series 10 switching per unit. The 2635 can be powered from any AC source 100-240 VAC or 28 VDC so you can use it anywhere in the world.
-
product
System Trace Emulators
XDS560v2
The XDS560v2 System Trace Emulator is the second generation of the XDS560-class emulator design from Texas Instruments. It provides cost effective real-time emulation, debugging, and high-performance System Trace (STM) for Texas Instruments devices over both USB and Ethernet PC interfaces.
-
product
4 Wire Earth Resistance & Resistivity Tester
4235 ER
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.
-
product
Gauge Type T Thermocouple Wire
W-TW-40P
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
Trace Moisture Analyzers
Used primarily with air separators, medical gas, semiconductors and in pharmaceutical settings, Edgetech Instruments provides both stationary and portable units used to accurately measure moisture levels in dew point and PPMv units.
-
product
Wire Harness Tester
NX Pro
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
product
Gauge Type T Thermocouple Wire
W-TW-36P2
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
Post Wire and Die Bond Inspection Machine
IV-E1700
IV-E1700 is a post wire and die bond inspection machine that is known for having a proven, effective and patented 2D+3D Inspection system. This product is best used to weed out defects with data collection for process improvement and reports for SPC quality Control.
-
product
- RS-232 to RS-422/RS-485 Concentrator - Wiring Hub
Model 290
FEATURES: Break RS-485 Limit, Expand to 496 Nodes 16 Port Capacity; Each Port Settable to RS-422 or 2 Wire RS-485; Provides Isolation Between Ports; All Ports Surge Protected; Increased System Reliability. The Model 290 RS-232 to RS-422/RS-485 Concentrator offers a unique group of features for those applications using RS-422 and/or RS-485 for communications between a multiplicity of devices.
-
product
Trace Gas Analyzers
Campbell Scientific offers both open-path and closed-path trace gas analyzers for measuring carbon dioxide and water vapor. Campbell Scientific also offers a closed-path analyzer for measuring methane, nitrous oxide, or isotopologs of carbon dioxide.
-
product
Resistance Wire Bonding
Electronic Systems of Wisconsin, Inc.
ESW's Resistance Wire Bonding System comes equipped with the latest features the market has to offer. Our system is capable of bonding armatures, stators or coils. The on-screen display in our bonder makes it easy to read, track, and record your bonding data. If desired, ESW offers complete electrical testing of the part prior to the bonding sequence as well. This ensures only good parts that have been electrically tested are processed through bonding. It is our duty to make sure you never have to worry about losing important information again. Our Sales and Engineering staff will work closely with you to make sure that a bonding systems will meet your needs. See the slideshow below to see some of our Resistance Wire Bonding Testers.
