-
product
68-Pin SCSI Micro-D Male Discrete Wire
40-962-068-M
This connector is designed to allow users to directly terminate with IDC connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
product
Compact Measurement System For Steel Wire And Rods With Small Diameters
A glowing hot wire is pulled through the rolling mill at about 120 meters per second during ongoing production. Speed, high temperatures and dirt are special challenges for a high-precision measuring system. Our solution is the Contour Check Wire. It is specially designed for the geometric measurement of wires, rods and rebar and, at 800 Hz, offers the optimum measuring rate for accurate data acquisition. In the uniaxial version, you can check the diameter; in the two- to three-axis version, the ovality can also be determined. The small dimensions and light weight allow a quick and easy integration of the Contour Check Wire into the existing line.
-
product
Pull-Thru Adapter, Wired, QuadraPaddle, to 68 Pin SCSI Female
510140251
Pull-Thru Adapter, Wired, QuadraPaddle, to 68 Pin SCSI Female
-
product
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-139-101
510140254
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-139-101.
-
product
Wire Crimp Pull Tester (Motorized)
WT3-201M
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 200 Pin Male LFH
510109488
PCB adapter from a 192 position QuadraPaddle receiver module to one 200 pin male LFH connector
-
product
I-V Tracers
EKO I-V tracers (MP-160 / MP-11 / MP-180) can be used in three different Power ranges. The research type MP-160 is an all round instrument to be used with single cells and modules or multiple unitswhen connected to the multi channels selectors. The portable MP-11 with remote sensor unit can be used on site to accurately check the performance of Modules and Strings. The high end MP-180 is capable to make high precision I-V measurements of small and large size solar cells and is most suitable for Research and Development applications or production inspection purposes indoors.
-
product
Cable Locators, Route Tracers And Height Meters
CHM cable height meters are easy to use, handheld devices which use ultrasound to determine the height of up to six overhead cables and wires. They are designed to measure cable sag, overhead clearance and cable heights up to 23 m, with separate products dedicated to the power and telecommunications markets. As a safe alternative to telescopic ranging sticks, there is no physical connection to the cables.
-
product
Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles
DEFECTOMAT® Product Familiy
Foerster Instruments, Incorporated
The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.
-
product
3 Wire (Analogue) Earth Resistance Tester
ST-1505
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● The timer operates automatically for about three to five minutes when the “PUSH BUTTON SWITCH” and “TIMER ON BUTTON” are pressed together. ● This will keep test “ON” for the duration of the timer.● Battery check function.● Calibration performed with supplied test leads.
-
product
Test Lead Holder For Wires Up To 0.320In (8.13mm) Dia
4408
Test Lead Holder for Wires Up to 0.320in (8.13mm) Dia
-
product
MTA Wiring Analyzer
2650
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
product
3 Wire (Analogue) Earth Resistance Tester
1105 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
product
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions
510109598
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions.
-
product
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs
510140111
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs.
-
product
Signal, Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Square Posts for Wire Wrap with Anti-Rotation (610 138 122)
510151124
NOTE: Part # 510151124 Rev D and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
product
Tool, Crimp Die, Micro Coax, f/ RG 316 and RG 179 wire
910101133
Included in Tool kit 910101132.
-
product
Protective Cover, 9050, VXI and Discrete Wiring, Receiver
310113285
When the Receiver is not in use, the Protective Cover is used to protect the modules and contacts. The Protective Cover is made up of black anodized aluminum.
-
product
Heavy Duty Circuit Tester with 12' Retractable Wire & Battery Clip
27300
Features an extra long wire that stretches up to 12 feet for use, then automatically retracts. Quickly and easily check electrical circuits and accessories on 6 and 12 volt systems. Great for use on cars, trucks, boats, trailers, motorcycles, airplanes and snowmobiles. Heavy duty ground clip with insulator. 3 1/4" standard length probe
-
product
PXI Pull-Thru Adapter, Wired, Mini Coaxial, to 4 SMB Plugs and 4 BNC Plugs
510140157
PXI Pull-Thru Adapter, Wired, Mini Coaxial, to 4 SMB Plugs and 4 BNC Plugs
-
product
Telephone Wire Cable Tester For Testing Continuity With Sender And Receiver
PHCT55
The PHCT55 is a two-piece item that tests telephone wire continuity. Play a test tone on one end and listen on the other, judge continuity, and diagnose break points.
-
product
1 Ft Harness, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97103
1' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
product
Field Portable Wire Analyzer
Model 2635
The perfect tester for field use is rugged, mobile, and lightweight, without sacrificing the functionality and power of a larger system. That tester is found in the Model 2635. Weighing 32 pounds (14.5 kg), this wiring analyzer handles up to 400 test points of Series 10 switching per unit. The 2635 can be powered from any AC source 100-240 VAC or 28 VDC so you can use it anywhere in the world.
-
product
Glow Wire Test Apparatus
GWT A2
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
product
15' Cable, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97112
15' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
product
3 Wire (Analogue) Earth Resistance Tester
4105 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
product
High Altitude Wiring Clamp
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
product
Power Device Analyzer / Curve Tracer
B1505A
The Keysight B1505A Power Device Analyzer / Curve Tracer is the only single box solution available with the capability to characterize high power devices from the sub-picoamp level up to 10 kV and 1500 A. These capabilities allow evaluation of novel new device such as IGBT and materials such as GaN and SiC. The B1505A supports a variety of modules: high voltage SMU (HVSMU), high current SMU (HCSMU), ultra high current (UHC) module, ultra high voltage (UHV) module and high voltage medium current (HVMC) module. The B1505A also supports: high-power SMU (1 A/200 V), medium-power SMU (100 mA/100 V) ,medium-current SMU (1 A/30V pulsed, 100 mA/30V DC) and a multi-frequency capacitance measurement unit (1 kHz 5 MHz). Its ten-slot modular mainframe allows you to configure the B1505A to suit your measurement needs.
-
product
ITA, G18, 18 Module With Discrete Wiring And PCB Capability
410120101
ITA, G18, 18 Module with Discrete Wiring and PCB Capability
