Fault
-
Product
ISDD Tool Suite
-
The Integrated System Diagnostic Design or ISDD Tool Suite provides a start to finish solution for meeting all the diagnostic needs of system design. The ISDD design process is centered around functional modeling of systems which is used to develop the diagnostics and failure analysis necessary to fully support good system design. This includes: *Analysis of Fault Detection and Fault Isolation.*Analysis of critical failures and their impact upon safety.*Detecting and reducing false alarms caused by diagnostics.*The impact of prognostics upon fault detection/fault isolation and mitigation of critical failures.*Development of vehicle health management and troubleshooting diagnostics
-
Product
Audio Frequency System
Locator Set / UL 30
-
Cable fault location with the BAUR Locator Set / UL 30. The audio frequency system Locator Set is used to exactly determine the alignment of cables and metal gas or water pipes. With various accessories, this system becomes a universal, indispensable device for power companies, industries, installation companies and water suppliers.* Output energy up to 50 VA* Automatic or manual impedance adjustment* Charging unit and rechargeable battery integrated; battery or mains operation* Continuous or cyclical output
-
Product
Platinum Tools Fiber Optic Visual Fault Locator
#TVFL100
-
Fiber optic visual fault locator works with virtually all 1.25mm and 25mm fiber optic sizes and connector types.
-
Product
DC Safety Inspection Device For Solar Panels
“DC Fault Tester”
-
Identifies defect position instantly- contributes to saving inspection time
-
Product
Electrical Fault Detector
-
Our product range includes a wide range of Electrical Fault Detector and 0.36W Electric Fault Detector.
-
Product
PXI 34-Channel 4-Bus 2A Fault Insertion Switch
40-197A-001
Fault Insertion Unit
This 34-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers. A low cost 16-channel option is also available.
-
Product
Intelligent Cable Fault Locator
TM800
-
TM800 Cable Fault Locator is a portable field instrument working on TDR and bridge methods, adopting advanced micro-electronics technology. It is designed to locate accurate fault points in such cables as telecommunication leadsheathed cable, plastic cable or user’s lead covered wire, while the faults include break, mix, earthing, defective insulation, or poor connecting. It is and ideal function-stable instrument for the field operator to improve work efficiency, in addition, it can also be used for circuitry project checking electric property testing of the cable.
-
Product
Optical Fiber Ranger
OFR300
-
Shanghai Tarluz Telecom Tech Co., LTD
OFR300 Optical Fiber Ranger is the most portable test instrument in the industry. It adopts the OTDR technical principles and integrates the powerful analysis software, which enables the OFR300 fiber ranger detect fiber faults location more accurate and easy.
-
Product
Cable Testers
-
Passage test:Detects open wires, short circuits and faulty wiring. Pass / fail test using a given pattern cable. Finding intermittent connections.Save cable data for documentation purposes. Print wiring diagrams. Printing labels. Log and print error logs.Graphical representation of the wiring of cables, graphical comparison of two cables. Easy, intuitive, graphical tracking of individual wires of a cable.Quickly install quick-mount boards for a variety of connector types such as BNC, RJ45, Sub-D, flat-ribbon connectors, and many more.Easy connection to the PC via USB .Light Director System:LED-led assembly of connectors. Optional also with voice output. High degree of safety due to fault checking during assembly.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-60NK
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement*DC leakage current measurement*Least affection from the magnetization of core and temperature fluctuation*Convenient ＋24V single polarity power supply
-
Product
PXI Vehicle Multiprotocol Interface Module
Interface
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Noise and Vibration Tester
-
SKF Condition Monitoring Center
High tech analysis and measurement such as frequency analysis (FFT) and further advanced analysis pinpoints faults. Spectral masks help to optimize the bearing performance in the particular customer application.
-
Product
DC Power Supply
-
Our broad selection of both bench-friendly and system-ready instruments can meet your testing challenges - from basic to complex - with a wealth of available capabilities.Test confidently with clean, precise DC power that's fully specified and guaranteedSafeguard loads from potential harm with robust output protection and fault detection capabilitiesEnhance system flexibility with built-in, DMM-quality measurement functions
-
Product
Defect Review Station Software for electrical test
Faultstation
-
Centralize all error review for your different testers in a single seat! To capture PCB layout information, FaultStation offers the choice of DPF or IPC input. In combination with a Ucamco data-prep seat, DPF is the obvious choice, while industry standard IPC provides a doorway to all other data-prep systems in today’s marketplace. Once the layout data is available, you combine it with the error information from a variety of different models and makes of testers.
-
Product
PXI BRIC4 FIBO Matrix Dual 155x4 2pin brkout
40-592A-115
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Fault Insertion Unit
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
PXI-6511, 64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module
778967-01
Digital I/O
64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6511 is an industrial digital input interface, with eight banks of isolated channels. If a computer or application fault occurs, the PXI‑6511 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Multi-Function Recorder
Platinum 2.5K
-
For all types of power system events, the Platinum 2.5K Multi-Function Recorder provides all the information you need to capture the complete picture. This comprehensive fault recorder simultaneously performs transient, sequence of events and disturbance recordings, phasor measurements and power quality analysis. All of these functions are performed at the highest level so it will meet your needs of today and the future. In a deregulated environment, the Platinum 2.5K is the best tool to provide the necessary data to increase revenues and retain your customer.
-
Product
PXI BRIC8 HD FIBO Matrix 186x8 2pin brkout
40-592-121-186X8-2P
Matrix Switch Module
The 40-592 FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC™ format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short-circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Test Extension Boards
XJIO
-
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
Product
High Resistance Neutral Grounding Devices
-
HRG systems limit the fault current by placing high resistance between neutral point of transformer (or generator) and ground. As it is not possible to locate the fault point in delta connected systems, an artificial neutral point is created and delta connected system can be grounded. This allows a fault current of a few amperes thus locating the fault point gets easy. When the neutral point is grounded thru high resistance, both continuity of operation is provided during fault condition and sufficient current (typically between 2 A and 10 A) flow is provided for ease of locating the fault point.
-
Product
Wireless Vibration Analyzer- ARGUS
ARGUS
-
Signals & Systems India Private Limited
Argus Tri-axial wireless vibration sensor enables easy condition monitoring of rotary machines and detects faults well soon before the equipment failure. The super-compact, IP67 rated vibration sensor provides reliable data for continuous monitoring and remote diagnostics. This Tri-axial sensor communicates with Android devices in both wired and wireless modes. The dedicated Argus app enables Multichannel Data Acquisition for simultaneous monitoring of various nodes.INCREASE MACHINE LIFESPAN - EARLY DIAGNOSIS ELIMINATES PROBLEM SEVERITY WHICH IN TURN ENHANCES MACHINE LIFESPANREDUCE YOUR RISK - REMOTE MONITORING ENSURES EMPLOYER SAFETY IN A HAZARDOUS ENVIRONMENT.50% REDUCTION IN MAINTENANCE COST - PREDICT & RECTIFY THE FAULTS EARLY TO LOWER THE UNDESIRED MAINTENANCE COST.40% REDUCTION IN UNPLANNED DOWNTIME - REDUCE MACHINE DOWNTIME AND INCREASE THE PRODUCTIVITY.
-
Product
PXI BRIC4 FIBO Matrix Dual 93x4 2pin brkout
40-592A-013
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Load Cell Simulator
-
A High-Stability adjustable Load Cell Simulator. It is specifically designed for Load Cell Fault and System Fault Diagnosis. It also provides a useful Development Tool for any System which relies upon Load Cells. The Output Signal is adjustable from -0.1 to +3.1 mV/V.
