-
Product
High Purity Gas Measurements
DF High Purity
-
When your processes need high purity gas measurements for oxygen and moisture, DF analyzers deliver industry-leading performance that reaches down to the very lowest ultra-trace levels. Utilizing the exceptional sensing capabilities of Servomex’s coulometric and TDL sensing technologies for the measurement of oxygen and moisture respectively, DF analyzers are optimized for a sensitive and stable analysis at ppm, ppb and ppt levels.
-
Product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (m)
CK058M
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781260-02
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
H2/O2 Analyser For Nuclear Power Plants
-
Our high performance analytical systems have been used in the nuclear industry since 1980. They enable operators to monitor hydrogen and oxygen levels at critical locations within both boiling water reactors (BWR) and pressurised water reactors (PWR).
-
Product
Food Analyzers
-
The function of the milk analyzer is to make quick analyses of milk on fat (FAT), non-fat solids (SNF), proteins, lactose and water content percentages, temperature (oС), pH, freezing point, salts, conductivity as well as density of one and the same sample directly after milking, at collecting and during processing.
-
Product
Dynamic Image Analysis (DIA)
CAMSIZER
-
Dynamic Image Analysis (DIA) is a modern particle characterization method for the determination of size distributions and shape parameters. It allows quick analyses with excellent accuracy and reproducibility over an extremely wide measuring range. With the renowned CAMSIZER system, Microtrac introduced its first Dynamic Image Analyzer over 20 years ago and has pushed technological innovation ever since.
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Portable Gas Analyzer
PG-300 Series
-
The PG-300 is a compact and lightweight stack gas analyzer that can simultaneously measure up to five separate gas components. Its capability of providing precise measurement has been proven for field measurements and also for laboratory applications. The PG-300 series also offers the capability to measure methane (CH4). A 20% weight reduction over previous PG models and integration of shock-resistant side guards make the PG-300 a robust analyzer for use in the field. An optional electronic cooler unit is available for long-term measurements for severe monitoring applications as gas turbines, boilers, and incinerators PG-300 series versatility makes the analyzers suitable for investigating environmental problems, evaluating catalyst performance, and for controlling process gas streams.
-
Product
ATEX Gas Analyzer
atmosFIR EX
-
atmosFIR EX is an ATEX certified gas analyser system for measurement of industrial gases in a Zone 1 or Zone 2 area, providing a complete EX certified gas measurement system that meets both the sampling of non-flammable and flammable gases, utilizing Protea’s multigas atmosFIR FTIR gas analyser platform.
-
Product
Test & Measurement
-
NIF (Dutch Instrument Factory, later Nieaf-Smitt) started in 1900 as one of the first organizations in the world with the design and production of instruments for electrical values. The portfolio of test tools, digital multimeters, current clamps, device testers, installation testers and power analyzers is characterized by quality and reliability.
-
Product
TorqueMate® Torque Analyzer
PTT-Series
-
The PTT torque meter makes quality documentation faster and easier. As an advanced torque controlling, monitoring and documentation solution, the torque analyzer enables operators and engineers to ensure product quality, safety and reliability promptly in a variety of manufacturing environments. The portable torque meters are designed for measuring torque, torque calibration, joint testing, auditing or force and load measurement. The failure of a three-cent fastener that isn’t properly tightened can lead to catastrophic or latent failures. Using a quality torque tester makes a safer world through accuracy and precision.
-
Product
Automatic Calibration Module
ACM4509
-
ACM4509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full four-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to 18 connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
Automation
Signal Filtration
-
Signal Filtration is used for filtering signals coming to the input channels of spectrum analyzers, strain-gauge stations, and seismic stations, for further processing by ZETLAB programs. Signal Filtration can also be used for processing virtual channels created by such programs as Vibration Meter, Strain-Gauge Sensor, etc. Signal Filtration operates with signals both in real time and with reproduced of recorded signals.
-
Product
Handyscope TP450-250XM-W5
TP450-250XM-W5
-
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
Product
Electroplating Bath Analyzer
-
optek’s electroplating analyzers are inline devices designed to measure plating solution’s metal concentration in real time. These analyzers can be designed to accommodate virtually any concentration range. Operationally, the analyzer passes a white light beam through the plating solution to be monitored. Then, light absorbance is measured at two distinct wavelengths, and the difference in light absorbance between the two wavelengths is equated to a plating solution concentration.
-
Product
USB Reusable Temperature and Humidity Data Logger
-
This reusable logger can monitor temperature and humidity in facilities, storage and processing areas, clean rooms, labs, and during transport. It is equipped with an external sharp tip probe, providing the option to monitor internal core temperature. Data is available in PDF or spreadsheet format and used for various purposes, such as process or equipment verification and validation, thermal mapping, and documenting environmental conditions to meet GMP, GDP and regulatory compliance. Reports are analyzed to identify trends and patterns, and management decisions can be made to improve practices in areas such as processing and cold chain logistics. Data is easy to archive for record keeping, audits, and compliance with FDA, CDC, HACCP, FSMA and other regulatory requirements.
-
Product
Engineering Services
-
When you buy a measurement instrument or a sensor from a PST brand we will offer you a complete solution. PST engineering services have been helping customers around the world to deliver the right product configuration for the most challenging applications. Our experienced engineers can help you with gas pipe design, analyzer cabinet design or will design the entire gas sampling and conditioning system for your measurement product. If you are an OEM customer we offer product customisation to exactly meet the required specification of your product.
-
Product
Mixed Domain Oscilloscope
3 Series MDO
-
With the largest display in class, improved low-level signal measurement accuracy and industry-leading probe performance, the 3 Series MDO sets a new standard for bench oscilloscopes. Whether you’re testing your baseband design for IoT or just for simple EMI sniffing, the 3 Series has a unique true hardware spectrum analyzer built right in with superior RF test performance and guaranteed RF specifications.
-
Product
PDA Software Simplifies Ethernet Powered Device Testing
-
All PDA-600 Powered Device Analyzers come with productivity software including the PDA Interactive graphical user interface and the PowerShell PDA script automation development environment. Also included is an Windows binary API library to provide programming extensions to a variety of programming languages.
-
Product
Powered Device Analyzer for 802.3at
PDA-602B
-
Emulate all Type-1 and Type-2 PSE’s, powering 2-pairs up to 41W at all PD input voltages. Optionally supports 802.3at PD Conformance Test Suite and LLDP emulations.
-
Product
Servo Analyzer (Frequency Characteristics Analyzer)
DS-0342
-
The DS-0342 Servo Analyzer (Frequency Characteristics Analyzer) is a device that measures the transfer function (frequency response function) of control circuits and mechanical structures with high accuracy.It can measure characteristics (phase margin, gain margin) of the control circuit, resonance frequency of the structure, and impedance, etc.This is a PC based servo analyzer that pursues usability with the following functions in addition to "easy-to-use operability" and "diversity of graph display".
-
Product
Mixed Signal Oscilloscope - 1 GHz, 4 Analog Plus 16 Digital Channels
MSOX3104T
Oscilloscope
1 GHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Arc Infrared Carbon and Sulfur Analyzer
CS-8620
-
Wuxi Jinyibo Instrument Technology Co., Ltd.
Infrared carbon and sulfur analyzer is used together with high-speed automatic ignition furnace to quickly and accurately determines the mass fraction of carbon and sulfur in steel, iron, alloy, non-ferrous metals, cement, ore, catalyst and other materials. a high-tech product integrating light, electromechanical, computer and analytical technology. It has the advantages of wide measuring range, strong anti-interference ability, complete functions, simple operation, accurate and reliable analysis results, etc. It is the ideal for measuring Carbon and sulfur in many industries. Analytical equipment.
-
Product
SureTest® Circuit Analyzer
61-164
-
*Measures voltage drop under load**Hot and neutral conductor impedances*Estimates Load on Line (ELL) up to 15A*Tests GFCIs and EPDs for proper operation*Super-bright OLED display*High accuracies*True RMS*Line and peak voltage*Identifies proper wiring in 3-wire receptacles*Identifies false (bootleg) grounds*Tests without disturbing sensitive loads*Verifies isolated grounds (with 61-176 adapter)*2-year warranty*12A, 15A, 20A load tests
-
Product
Keysight Streamline USB Vector Network Analyzer, 6.5 GHz
P9371A
Vector Network Analyzer
Compact, faceless, USB vector network analyzer (VNA). Affordable full two-port VNA which dramatically reduces your size of test. Up to 6.5 GHz.
-
Product
Vector Network Analyser
LA19-13-02
-
The LA19-13-02 is a PC-driven Vector Network Analyser suitable for measuring a wide range of devices from 3 MHz to 3 GHz with 100 Hz resolution. Its full s-parameter test set includes bias-Ts for biasing active devices. It is housed in a small lightweight package making it very portable.
-
Product
Vector Network Analysers
LA19-13-03
-
The LA19-13-03 is our latest PC-driven Vector Network Analyser. It provides great flexibility, fast speed and wide dynamic range. It is useful for measuring a wide range of devices from 300 kHz to 8 GHz with 10 Hz resolution. By means of external links on the front panel, the internal couplers can be bypassed for direct access to the internal receivers. This flexibility allows, for example, high power amplifier measurements to be carried out using an external booster amplifier and couplers. It is housed in a small lightweight package making it very portable.
-
Product
DCA-M Sampling Oscilloscopes
-
Built on Keysight's digital communication analyzer (DCA) technology, the DCA-M family is recognized as the industry standard for verifying optical transmitter compliance to communications standards. With single to quad optical AND electrical channels in a compact form factor, the DCA-M is ideal for both manufacturing and RND applications. Analyze both multi-mode and single-mode signals with the low-noise, high-sensitivity calibrated reference receivers. The variety of models along with the supporting software and compliance applications ensure you can measure with high precision, whether you analyze electrical or optical devices.
-
Product
PXI Vector Signal Analyzer
Vector Network Analyzer
Keysight's PXIe vector signal analyzers are ideal for design validation and manufacturing applications that require fast, high quality measurements where quality control, product conformance and test optimization are essential. With a small footprint, speed, scalability repeatability, and the flexibility to configure a solution with a shared processor, frame/chassis, display, and interface, PXIe vector signal analyzers provide the building blocks for your single or multi-channel modular test solution.
-
Product
4-Port 9 GHz Analyzer, Frequency Extension Compatible
C4409
-
C4409 Vector Network Analyzer delivers industry-leading dynamic range and sweep speed, with all the features engineers have come to expect included standard in our software. This VNA is frequency extender compatible and is the anchor network analyzer for the CobaltFx frequency extender system.
