Network Analyzers
software and/or hardware, that measures the activity on a network and the devices connected to the network.
See Also: Network, Vector Network Analyzers, Electrical Network Analyzers, Optical Network Analyzers, Portable Network Analyzers, Power Network Analyzers, Radio Network Analyzers, Scalar Network Analyzers, Wireless Network Analyzers, Impedance Analyzers
-
product
ENA Vector Network Analyzer
E5061B
Select the best configuration for your test needs from a wide variety of test set options: 100 kHz to 1.5 GHz/ 3 GHz, 2-port, 50 or 75 ohm, transmission/reflection or S-parameter test set Address a broad range of applications with the LF-RF option (Option 3L5/3L4/3L3): 5 Hz to 3 GHz, 2-port, 50 ohm, S-parameter test set, gain-phase test port, built-in DC bias source Combine network analysis and impedance analysis to customize your application in a single instrument (Option3L5/3L4/3L3 plus 005) Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (f) 50 Ohm
CK521A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Phase Noise Measurement Up To 70 GHz
S930317B
S930317B enables phase noise measurements using a PNA or PNA-X vector network analyzer. Simplify your measurement workflow by measuring phase noise on the same connection as your network analysis measurement of 2-port active devices up to 70 GHz, without needing to connect a spectrum analyzer or harmonic mixer.
-
product
Network Analyzer, Lan Tester, LED
72-6706
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
product
Broadband VNA Operation To 220 GHz
S93301B
Configure a 220 GHz broadband vector network analyzer (VNA) for on-wafer device characterization of emerging 5G and 6G MMICs
-
product
Automatic Calibration Module
ACM2543
ACM2543 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 44 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
product
2-port E-Band VNA Using Streamline 20 GHz 4-port Network Analyzer
N5253E1
Cost-effective 2-port E-band vector network analyzer (VNA) system configured with a Streamline VNA and frequency extenders.
-
product
Automatic Calibration Module
ACM2506
ACM2506 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 6.5 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
product
110 GHz Frequency Extender, Pulsed DC Bias
N5293AX52
The Keysight N5293AX52 is a broadband frequency extension module designed for use with Keysight’s new PNA / PNA-X-based millimeter-wave solutions. It is a compact, lightweight, and ruggedize frequency extender module with built-in bias tee for pulsed DC bias operation. It interfaces with the Keysight N5292A test set controller. The modules allow users to extend the frequency coverage of a base PNA / PNA-X Series network analyzers to a range of 10 MHz to 110 GHz. For more information about cable and accessories for use with network analyzers, please visit Network Analyzer Accessories.
-
product
ENA-X Vector Network Analyzer
E5081A
Our spectral correlation technique directly analyzes the modulated input and output signals in the frequency domain on the network analyzer. Current solutions on the market require a network and spectrum analyzer to characterize components fully. With the new ENA-X, you can ensure test accuracy and repeatability with a single test setup using full vector correction at the DUT plane. Avoid manually reconfiguring setups or automating complex switch-based systems — verify device performance faster and with less error potential with the ENA-X network analyzer.
-
product
Streamline USB Vector Network Analyzer, 32 GHz
P5006A
Compact, faceless, USB vector network analyzer (VNA). Flexible two port VNA which dramatically reduces your size of test. Up to 32 GHz.
-
product
ENA Vector Network Analyzers
Create accurate, dependable test stations with high throughput, repeatability and reliability Streamline your measurement flow with intuitive user interface and achieve better results in less time Secure your assets with upgradability, including software and hardware such as frequency and test port
-
product
Instrument Measurement Software
Get quick insights and reduce the test time of your devices with instrument measurement software or test instrument software specifically designed for spectrum analyzers, oscilloscopes, network analyzers, and many more test instruments.
-
product
120 GHz Frequency Extender, Pulsed DC Bias
N5295AX52
The N5295AX52 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 120 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
product
Cable Assembly with 2.4mm Male Connectors
Y1740A
The Y1740A is a flexible cable with excellent phase stability. This cable is recommended for accurate S-parameter measurements using the following Keysight vector network analyzers: Streamline Series VNA, M983xA/M980xA Series PXIe VNA, or M981xAS series PXIe Vector Component Analyzer (VCA).
-
product
N-port Calibrated Measurements
S97551B
The S97551B software enables full multiport error correction and measurement capabilities when using multiple USB vector network analyzers
-
product
Frequency Expansion Modules
bsw TestSystems & Consulting AG
Up To 1.5THz For Network Analyzers Modern communication standards, like for instance 5G, place high demands on components (mixers, amplifiers, antennas, etc.), which have to be examined in high frequency bands (millimeter waves); the requirements include: broad frequency coverage, sufficient output power to operate the components under compression, high dynamic range and stability as well as a reduced dynamic content within the spectrum.
-
product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
product
Streamline Vector Network Analyzer, 100 KHz To 44 GHz, 2-port
P9377B
Compact, faceless, vector network analyzer (VNA). Affordable full two-port VNA which dramatically reduces your size of test. Up to 44 GHz.
-
product
Vector Network Analyzer Leasing Option
Companies in the United States can now lease a CMT VNA from Leasing Corporation of America. Leasing is a great choice for organizations that may not want to spend capital budget up front since lease payments are an operating expense. Choose from 2, 3, 4, and 5-year options. Pay as you use the VNA, with a fixed monthly payment and a 90-day deferred payment option. At the conclusion of the leasing period the equipment can be bought out for $1.00 plus a lease termination fee of $99.00.
-
product
PNA-X Microwave Network Analyzer, 26.5 GHz
N5242B
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Real-Time Spectrum Analyzers
RSA 3000E Series
The RSA3000E is a 5-in-1 spectrum analyzer with sweep spectrum, real-time spectrum, scalar network analyzer (-TG model), EMI receiver and digital demodulation. Its frequency range is 9kHz to 1.5/3GHz, and it is available with the tracking source "-TG" model, which can be widely used in enterprise R&D, factory production, education and teaching.
-
product
FieldFox Handheld Microwave Analyzer, 32 GHz
N9950B
A lightweight, durable, software-enabled cable and antenna analyzer, spectrum analyzer, network analyzer, and more.
-
product
4-in-1 OSLT Calibration Kit, DC to 18 GHz, Type-N (f) 50 Ohm
CK519A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Streamline Vector Network Analyzer, 9 KHz To 6.5 GHz, 2-port
P9371B
Compact, faceless, vector network analyzer (VNA). Affordable full two-port VNA which dramatically reduces your size of test. Up to 6.5 GHz.
-
product
Digital Electrical Network Analyzer
2126 NA
Standard Electric Works Co., Ltd
Microprocessor-controlled. Built-in earth tester. Built-in loop/psc tester. 0.03-2000Ω (software ctrl). Built-in voltmeter. Built-in wiring checker. One push button smart control. Display L-N and L-E voltages. 50 to 280Vac (sine). Display line path impedance. 0.01-2000Ω (software ctrl). Display earth path impedance. 0.01-2000Ω (software ctrl). Display neutral path impedance. 0.01-2000Ω (software ctrl). Display psc line to neutral. 6kA@230Vac supply. Display psc line to earth. 6kA@230Vac supply. Re-scroll through previous results. Bat. ok/low battery indicator. Auto off function. Color-coded test leads. Rugged case. Ultra low power consumption.
-
product
RF Electronic Calibration Module (ECal), DC/300 KHz To 9 GHz, Type-N, 2 Port
85092D
The Keysight 85092D RF electronic calibration (ECal) module makes calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.
-
product
PXIe Vector Network Analyzer Synthesizer: 187.5 MHz To 6 GHz
M9309A
The M9309A PXIe vector network analyzer (VNA) synthesizer is a component for the M9485A PXIe multiport vector network analyzer. Control the M9309A through the M9485A software front panel. The M9485A provides a true multiport VNA with up to 12-ports in one chassis and up to 24-ports in two chassis.
-
product
Wireless Antenna Analyzer using Bluetooth
miniVNA PRO
The new miniVNA PRO, the big brother of the well-known miniVNA, is an extraordinary and unique handheld vector network analyzer that makes available a multitude of new features and capabilities which are perfect for checking antennas and RF circuits for hams and commercial users.
-
product
System Amplifier
SAM100
The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals
