Transmission Electron Microscopy
-
Product
Electronic Boards
-
Computer Gesteuerte Systeme GmbH
The relay board 8AGN is a cost-effective board of the CM series, which is also used in our load modules, for example. It can be mounted on a 35 mm DIN rail. Currents up to 1 A at 30 V are possible. The maximum wire cross-section is 0.5 mm².
-
Product
Laser Raman Microscopy System
RAMANforce/RAMANtouch
-
Nanophoton is the pioneer of confocal laser scanning microscopy and spectroscopic analysis. To celebrate, we relaunch our fastest and highest resolution confocal Raman microscope RAMANtouch/RAMANforce. With a newly designed spectrograph and the latest optical technologies, RAMANtouch/RAMANforce’s spatial resolution and sensitivity have been highly improved, making it the optimal solution for all applications.
-
Product
Field-installation Type MLSS Meter (Four-Wire Transmission)
HU-200SS
-
HU-200SS connects immersion type MLSS sensor (SS-90) and measures MLSS in activated sludge. A wide range (0-2000mg/L)of SS contents can be measured with excellent reproducibility using the near-infrared radiation transmission method. Any of the calibration curves of MLSS, Clay (inorganic mud) and Kaolin may be used as standard substances of SS. If "MLSS" is selected for an activated sludge treatment tank, "Clay" for the precipitation treatment of construction sludge, or "Kaolin" for white mud, a concentration can be obtained closer to an analyzed value.
-
Product
Transmissive Rotary Disk
DISK-2
-
US Digital offers a wide variety of standard rotary encoder disks. They may be ordered as a stand alone disk (see below) or as a codewheel (see the Disks page). These rotary encoder disks are made from mylar polyester film. This material allows for a wide temperature range and is virtually unbreakable. There is no minimum order.
-
Product
AC and DC Electronic load
63800 series
-
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
Product
Plastic And Reconstructive Surgery Microscopy Solutions
-
Leica plastic and reconstructive surgery (PRS) microscopes give you the performance and reliability you need to repair intricate and fine structures during the most delicate reconstructive procedures. They feature high-quality optics, easy operation, and integrated visualization technologies, such as fluorescence filters and augmented reality (AR) fluorescence.
-
Product
Electronic Warfare Development Platform
SDR430
-
Abaco Systems and AMERGINT Technologies have partnered to develop an Electronic Warfare Development Platform: SDR430. This development platform comprises the latest open architecture digital signal processing hardware from Abaco combined with the SOFTLINK™ modular communications architecture from AMERGINT Technologies.
-
Product
High Current Probes (Power Electronics) HCF73212A200U300
1010644
-
The HCF73212A200U300 High Current Probes are advanced power electronics tools designed for precision and reliability in demanding environments. Featuring a basic contact probe design, these probes are capable of handling continuous currents up to 20A while maintaining a low typical contact resistance of 10 mOhm. The probes exhibit a temperature tolerance ranging from -45°C to +200°C, making them suitable for various applications requiring durability under extreme thermal conditions.
-
Product
High Current Probes (Power Electronics) HCF77312B230G300
1005048
-
The HCF77312B230G300 High Current Probe is engineered for precision applications in power electronics, exhibiting remarkable temperature resilience with a range from -45°C to +200°C. This basic contact probe excels in reliability, delivering a continuous current capability of 30A while maintaining a typical contact resistance of just 8 mOhm. Designed with meticulous attention to mechanical performance, it boasts a preload of 60 cN and a spring force of 300 cN, which provide optimal performance in demanding environments. The probe features a nominal travel of 4 mm, with a maximum travel capability of 5 mm, allowing for fine adjustments and ensuring a pointing accuracy of +/- 0.10 mm, making it an ideal choice for high-precision measurements.
-
Product
Electronic Load System
-
Electronic loads are required for testing fuel cells such as PEMFC, AFC, PAFC, MCFC, SOFC. These electronic loads are designed either in IGBT technology with power, current and voltage ranges according to specific requirements or in transistor technology. Electronic loads in IGBT technology are designed for high voltage ranges up to 900 V, current ranges up to 1000 A, and power ranges up to 480 kW.
-
Product
Multi-channel DC Electronic Load
IT8700 Series
-
IT8700 series programmable DC electronic load adopts removable modules design, supports up to 16 channels with mainframe extension transient mode up to 25 kHz, which improves your test efficiency, with high resolution and accuracy. Users can freely choose in the 8 load modules according to the number of channels and power requirements, controlled by mainframe control panel, or controlled by host computer software via built-in LAN / RS232 /USB / GPIB interface.
-
Product
Electronic Products
-
Sumitomo Electric Industries, Ltd.
Products found in the electronic realm.
-
Product
High Current Probes (Power Electronics) HCF77317B400G150
1139213
-
The High Current Probes (Power Electronics) HCF77317B400G150, specifically identified by the order code 1139213, is designed to meet the demands of modern electronic testing paradigms. This probe features a robust brass handle and is characterized by a basic contact probe design that ensures reliable electrical connection and superior performance. With its ability to operate under extreme temperatures ranging from -45°C to +200°C, the HCF773 is optimized for a variety of applications in power electronics.
-
Product
ELECTRONIC MEGOHMMETER
MI-2550e
-
The MI-2550e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 2,5 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 5.000.000 MΩ with four test voltages: 0,5 kV - 1 kV - 1,5 kV - 2,5 kV.
-
Product
Digital PIN Electronics Module
P128C200M
-
The P128C200M module provides measurement and control of parameters of integrated circuits using parametric measurement methods, as well as functional and algorithmic control. The module implements a synchronization system that ensures the operability of a group of modules when they are installed in the AXIe-1 crate.
-
Product
High Power DC Electronic Load
63200A series
-
The 63200A series high power DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more. The 63200A series have three operating voltage choices, 150V, 600V & 1,200V, with models covering power levels from 4kW to 24kW and up to 2,000A in a single unit. The DC loads have unique user defined waveform (UDW) capability and external analog modulating input for s imul a t ing re a l-wor ld, cus tom waveforms. Another distinct feature is the dynamic auto-frequency sweep function, which enables detecting a UUTs worst case output deviation across a wide range of current frequencies. In addition, a 255-set of data storage function has been built in for recall of the stored settings at any time. For automated testing, the save and recall functions can save a great deal of time.
-
Product
Electronic Outside Air Temperature
OAT
-
The outside air temperature sensor is an electrical component that complements the control of a modern heating system.
-
Product
600~1500W DC Electronic Loads
JT632 series
-
Nanjing Jartul Electronic Co., Ltd
JT632 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT632 series load very suitable for testing power supply when produced in large quantity. Besides, JT632 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT632 series load satisfing most of R&D requirements.
-
Product
Atomic Resolution Analytical Electron Microscope
NeoARM JEM-ARM200F
-
"NEOARM" comes with JEOL’s unique cold field emission gun (Cold-FEG) and a new Cs corrector (ASCOR) that compensates for higher order aberrations. The combination of a Cold-FEG and ASCOR enables atomic-resolution imaging at not only 200 kV accelerating voltage, but also a low voltage of 30 kV."NEOARM" is also equipped with an automated aberration correction system that incorporates JEOL’s new aberration correction algorithm for automatic fast and precise aberration correction. This system enables higher-throughput atomic-resolution imaging even at low accelerating voltages. Furthermore, a new STEM detector that provides enhanced contrast of light elements is incorporated as a standard unit.
-
Product
High Current Probes (Power Electronics) HCF77206B250G150A
1133508
-
The High Current Probes HCF77206B250G150A are designed specifically for efficient power electronics applications. This model, identified by the order code 1133508, operates effectively across a wide temperature range of -45°C to +200°C, offering robustness in various environments. They feature a basic contact probe design with an impressive typical contact resistance of just 10 mOhm, ensuring minimal energy loss during operation.
-
Product
High Current Probes (Power Electronics) HCF73306B300G150
1008216
-
The High Current Probes model HCF73306B300G150 is designed for precision applications in power electronics, offering a robust solution for measuring high currents. With a pitch of 4.00 mm and operating temperature range of -45°C to +200°C, these probes ensure versatility and reliability in harsh environments. They are built with a continuous current capacity of up to 30 A and maintain a typical contact resistance of just 8 mOhms, making them ideal for high-performance applications.
-
Product
DC Electronic Load Modules For The N6700 Power System
-
Test devices that store or convert energy by adding a DC electronic load to your Keysight N6700 Series power supply. The Keysight N6790 Series electronic load modules can perform a static or dynamic test and are available in two sizes: single-wide 100 W and double-wide 200 W modules.
-
Product
High Current Probes (Power Electronics) HCF71306B230G150
1024197
-
The High Current Probes (Power electronics) HCF71306B230G150, with order code 1024197, is designed for reliable and efficient operation in demanding environments, accommodating a temperature range from -45°C to +200°C. These basic contact probes feature a robust design with a pitch of 4.00 mm, making them ideal for high-performance applications in power electronics. With a continuous current rating of 30 A and a typical contact resistance of only 8 mOhms, they ensure minimal energy loss, contributing to overall system efficiency. The mechanical specifications highlight a preload of 70 cN and a spring force of 150 cN, providing a nominal travel of 2.80 mm and a maximum travel of 3.50 mm, complemented by a pointing accuracy of +/- 0.10 mm.
-
Product
Programmable AC Electronic Load
63800
-
Chroma Systems Solutions, Inc.
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing resulting in reliable and unbiased test results.
-
Product
Electronic Speed Controller
AFI-ESC1220
-
The AFI-ESC1220 is an Electronic Speed Controller designed to drive BLDC motors. It meets the industrial requirements of high power and high voltage application for electronic vehicles, airplanes, boats and medium duty industrial machinery. It is rated at 24KW.
-
Product
Electronics
-
We develop and deliver a wide range of advanced technologies for the commercial and military electronics markets. Our portfolio includes flight and engine controls, electronic warfare and night vision systems, surveillance and reconnaissance sensors, mobile networked-communications equipment, systems integration, and environmentally friendly energy management systems.
-
Product
High Current Probes (Power Electronics) HCF73206B200G225
1133498
-
The High Current Probes model HCF73206B200G225 is designed for precision in power electronics applications, delivering outstanding performance across a wide range of operating conditions. With a remarkable temperature range of -45°C to +200°C, this basic contact probe is engineered for versatility in various measurement environments while ensuring reliable connectivity. Its robust mechanical capabilities, featuring a preload of 60 cN and a spring force of 225 cN, allow for excellent handling even in demanding applications. The nominal travel of 4 mm and maximum travel of 5.3 mm contribute to its adaptability in different testing scenarios, making it an ideal choice for engineers and technicians alike.
-
Product
Load Cell Software And Electronics
-
Custom electronics and load cell software are viable low-cost solutions for OEM applications. With custom load cell software our customers can have exactly what is needed for the application and leave out the sometimes confusing extras that most off-the-shelf products have. We also offer private labels, overlays, and splash screens that will show your company's information on the display.
-
Product
Electronic Assembly
-
WinSoft employees succeed in some of the most demanding assembly operations - from aerospace disciplines, automotive, electronic manufacturing services and consumer products to COTS products.
-
Product
High Current Probes (Power Electronics) HCF77314B230G600
1000414
-
The High Current Probes (Power electronics) HCF77314B230G600 are engineered for precision in demanding applications, operating efficiently across temperatures from -45°C to +200°C. With a compact design featuring a pitch of 3.50 mm, these basic contact probes are optimized for high-performance in electrical circuits, ensuring reliable connectivity and minimal resistance. The continuous current capacity of 30 A and a typical contact resistance of just 8 mOhm positions this probe as a superior choice for power electronics professionals who need dependable tools that withstand extreme conditions.
