Device Characterization
-
Product
Medical Devices
-
As more medical devices become wireless, manufacturers will be looking for compact and affordable testing solutions for wireless components. Copper Mountain Technologies’ USB vector network analyzers provide portable, cost-effective network analysis solutions for medical wireless device applications.
-
Product
Semiconductor Device Parameter Analyzer/Semiconductor Characterization System Mainframe
B1500A
-
Current-voltage (IV) measurement capabilities of spot, sweep, sampling and pulse measurement in the range of 0.1 fA - 1 A / 0.5 V - 200 VAC capacitance measurement in multi frequency from 1 kHz to 5 MHz and Quasi-Static Capacitance-Voltage (QS-CV) measurement capabilitiesAdvanced pulsed IV and ultra-fast IV measurement capability from minimum 5 ns sampling interval (200 MSa/s)Up to 40 V high voltage pulse forcing for non-volatile memory evaluation
-
Product
Connected Devices
-
enable communication between devices. We provide connectivity for sensor applications and input devices via mobile communication and develop custom IoT solutions. Capturing, transferring and visualizing data increases your productivity and creates transparency.
-
Product
Bridge Devices
USB
-
*Royalty free Virtual Com Port (VCP) drivers*Simple GUI based Xpress configurator for configuring, programming and customizing applications*No USB expertise required*Seamless compatibility with most operating systems*UART, SPI, I2C/SMBus and I2S interface options available*Fastest way to add USB Turn key, no firmware development needed
-
Product
Discrete Devices Test
FTI 1000
-
The FTI 1000 tester consists of independent test channels that allow all DC and AC MOSFET parameters to be tested either separately, or in one handler insertion or prober touch-down.
-
Product
Embedded DisplayPort Electrical Performance and Characterization Toolset Software
D9040EDPV
-
Characterization testing of eDP designs now supporting AUX channel automation.
-
Product
Device Finder
-
Device Finder is a cross-platform application from Hall Research to find HR's IP enabled products on the local network. The software runs on Windows, MAC and Linux. Software not only finds HR devices but also allows user to new assign IP address(static/dynamic) to found device. It also has an ability to find devices which are on the different Subnet/VLAN but are on the same local network (connected to the same router).
-
Product
Automated Distortion Characterization and Information System
ADCS
-
Matrix Test Equipment Incorporated
The Automated Distortion Characterization and Information System (ADCS) is an extension of the Matrix equipment control software that automatically makes RF measurements selected from the following: Cross Modulation (XMOD), Composite Triple Beat (CTB), Composite Second Order (CSO), Carrier to Noise (C/N), Discrete Second Order, Discrete Third Order Distortion. Measurements are made, and the test results and a profile describing the test conditions are saved in a database for later retrieval or reporting.
-
Product
Protection Device Testing
-
The Motwane Manufacturing Company
Power system protection is a branch of electrical power engineering that focuses on protecting electrical power systems to detect and isolate faulty parts. The objective is to keep the power system stable by separating only the defective components while keeping the rest of the network in operation. The device protects the transmission lines, generator transformer, and other electrical apparatus from multiple faults.
-
Product
Measuring Devices For Nanoindentation
-
With our measuring devices, you can determine the mechanical properties of thin coatings reliably and accurately. From protective paint coatings to hardness of PVD coatings: We have the right solution for you. We offer you powerful and easy-to-use measuring instruments for the laboratory and production. You can choose from a wide range of accessories to adapt your device to your individual requirements.
-
Product
Testing And Inspection Devices
-
HEIDENHAIN offers testing and inspection devices that deliver all setup, monitoring, and diagnostic data needed for the analysis of its encoders. Grid encoders from HEIDENHAIN are ideal for machine tool inspection and acceptance testing, accurately measuring CNC machine tool movements in both static and dynamic inspection.
-
Product
Ethernet/Serial Device Server
-
Advantech serial device servers and gateways convert legacy protocols and interfaces to satisfy your various industrial automation needs.
-
Product
Battery Test device
ATGB 1200
-
The ATGB 1200 is a battery tester for all standard battery technologies aimed at quality assurance, production and product development. Advantages of the ATGB: Creation of customized test sequences. Generation of load curves and peaks. Temperature measurement at the battery
-
Product
High-Voltage Test Device
PGK 110 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 110 kV output voltage with positive or negative polarity* AC voltage testing - up to 80 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
Product
Measuring and Test Devices
ProfiMessage D
-
With a ProfiMessage D device, you can immediately begin using a optinal PROFINET interface as well as communicating to third-party systems via an OPC UA Server/Client. The device is also equipped with a display to show important configuration and measurement data. Other special features include universal sensor inputs, high-level data security, and a diverse range of interfaces.
-
Product
BAW Devices
-
Teledyne’s Bulk Acoustic Wave (BAW) Product Line has been producing BAW delay devices since the early 1960’s. Over the years, Teledyne Microwave Solutions (TMS) has constantly improved BAW technology and is currently the world’s only supplier of microwave bulk acoustic wave delay devices. Markets for BAW devices include instrumentation and radar altimeters and are available in connectorized, pin and surface mount configurations.
-
Product
PoKeys I/O devices
-
This board allows expanding the number of outputs of the Pokeys by using the PoExtBus. This board incorporates 16 high current/voltage open collector outputs which suits applications such as lamps, relays.
-
Product
Mobile Drone-detection Device
RadarZero
-
Compact drone detection radar product. At roughly the size of a paperback book, the product can detect drones up to 750m away and sells for a fraction of the cost of the larger longer-range more conventional radars.
-
Product
Semiconductor Device Testers
-
are particularly suitable for certain semiconductor test requirements, but other models may also be of interest. Our knowledgeable application engineers can guide you to the most suitable model.
-
Product
Analog Output Device
Analog Output Module
The Analog Output Device helps you create applications such as stimulus-response, power supply control, deterministic control, and sensor/signal simulation. The Analog Output Device supports various output resolutions, channel counts, and other onboard features, so you can replace several kinds of instruments in your system, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.The Analog Output Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Safety Locking Devices
-
Leuze electronic GmbH + Co. KG
Safety switches with locking device keep doors locked and thus prevent unauthorized entry or access, thereby protecting persons and processes. The L series features a wide range of variants for different application cases, from devices with mechanical actuators to devices with an RFID‑coded actuator for maximum manipulation protection as well as integrated command buttons. With their robust design, all devices are designed for rough industrial applications.
-
Product
High-Voltage Test Device
PGK 150 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Operation as DC or AC testing device* Polarity of the DC voltage can easily be reversed* Robust and durable
-
Product
CMP Process and Material Characterization System
CP-4
-
he new Bruker CP-4 CMP Process and Material Characterization System has been designed from the ground up specifically for reliable, flexible, and cost effective characterization of wafer polishing processes. Reproduces full-scale wafer polishing-process conditions. Provides unmatched measurement repeatability and detail. Performs tests on small coupons rather than whole wafers for substantial cost savings.
-
Product
Temp Characterized CalPod, 20 GHz
85531B
-
CalPods provide a new and unique way to quickly and easily refresh a network analyzer calibration, at the push of a button and without removing the DUT or re-connecting standards. Very useful in thermal chamber testing, where it is desired to remove the thermal effects of the test cables and connectors from the DUT’s response, and where it is impractical to stop the thermal testing to perform a normal re-calibration.
-
Product
Input Devices
-
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic's Electromechanical Components are used to convert mechanical movement into electrical signals. These products, including switches, encoders, and potentiometers, are used in everyday devices at the point of user interaction.
-
Product
Fan Characterization Module
FCM-100
-
Advanced Thermal Solutions, Inc.
The FCM-100 Fan Characterization Module is a specialized unit designed to test and characterize fans of various sizes and performance outputs. Using the FCM-100 Module in conjunction with pressure measurement equipment (such as the PTM-1000) and velocity measurement equipment (such as the eATVS); it is possible to develop fan curves (P vs. Flow rate) that can be used to verify fan manufacturer data or to characterize fans of unknown performance.
-
Product
FlexRay Interface Device
FlexRay Interface
FlexRay Interface Devices provide two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. FlexRay Interface Devices work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Power Semiconductor Device
IGBT/SIC
-
Hitachi High Voltage IGBTs have been corresponding to a wide range of applications such as railway applications and various power conveters, leading companies for domestic and overseas adopt them, since they were adopted as a railway application in 1992. Will continue to contribute to the developing energy society by pursuing more easy-to-use, high-performance and high -quality products with leading-edge research and development.
-
Product
Measurement Devices
-
In addition to the critical role data loggers play in a data-acquisition system, there are other types of measurement devices. Some measurement devices are used to increase the number of terminals that data loggers can use, which enables them to measure more sensors or control more external devices.
-
Product
Optical Measurement Methods and Characterization Services
-
The Fraunhofer IOF develops optical measurement methods and systems to customer requirements. Key areas include the characterization of optical and non-optical surfaces, coatings, components and systems in the micro and sub-nano range as well as 3D shape acquisition.
