-
Product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
Open Top BGA Sockets
-
Ironwood has the most comprehensive collection of open top BGA and QFN sockets that can be used for qualification application, silicon FIB testing, system development, thermal characterization, burn-in application, etc. IC socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. Typical packages include BGA, LGA, QFN, QFP, WLCSP, etc. Open top allows access to the top side of IC. Below is an example BGA socket that uses low cost elastomer contact technology.
-
Product
LCR Component Meter with Component Impedance Measurement
LCR45
-
The new LCR45 does everything that the popular LCR40 does, but we've added some significant enhancements. The LCR45 features a new high capacity micro and high resolution ADCs.*Fluid measurements of L, C and R (continuous readings with selectable hold function).*Fine resolution for improved performance at low inductance/capacitance/resistance.*Auto and Manual component type.*Auto and Manual test frequency.*Frequencies: DC, 1kHz, 15kHz and 200kHz.*Display of component values, complex impedance, complex admittance and magnitude/phase.
-
Product
Vibration Combined Test Chamber
-
Vibration and Temperature & Humidity & Vibration Combined Test Chamber offer combined temperature, humidity, and/or vibration environments. Weiber models are designed for compatibility with user’s choice of electrodynamic or mechanical vibration systems. While each model is manufactured to standard designs, they may also be custom engineered to meet a wide range of stringent test requirements. The Test Chamber comes with optional capability to interface with vibration systems in both the horizontal and vertical modes of operation with rear or vertical sliding doors. The Weiber Series temperature/humidity and vibration chambers are designed to integrate with vibration systems in only the vertical mode of operation.
-
Product
Polysilicon Resistivity Tester
HS-POSRT
-
HS-POSRT polysilicon resistivity tester is an advanced resistivity tester, it has features of wide resistivity measuring range, high testing accuracy, high stability, swift body and easy operation. It is a good friend to Siemens polysilicon material producer,SH4 polysilicon material producer, UMG polysilicon material poroducer and so on
-
Product
LCM Tester
Model 27011
-
To meet the high accuracy and low price requirements for LCM Test device, Chroma 27011 that integrates the signal and power source provide a complete test solution for LCD Module. Its LVDS, TTL signal source fully complies with the digital signal standard, meanwhile with the 12V, 5V, 3.3V DC source output it is able to supply power to VDD, Backlight or LCM test without obtaining external power source.
-
Product
Film Shrink Tester
-
The Hanatek FST Film Shrink Tester is used to measure the effect of temperature on plastic films. The application of heat causes certain plastic films to rapidly contract; this effect can be used to seal and pack many items from food to consumer goods. The shrink effect is due to internal forces locked into the film during manufacture being released by heating, it is also known as linear thermal shrink or free shrink. The amount of shrinkage is dependent on the film type, thickness and sealing temperature. Testing the percentage shrink of a film ensures that it is suitable for a particular packaging application and establishes the correct temperature for that application.
-
Product
Colorimeter
Model CA-600
-
Teledyne Analytical Instruments
The CA600 is an online sequential sampling analyzer, using colorimetric methods. The analyzer can be configured to most laboratory colorimetric tests in individual processes.The CA600 Analyzers are easy to start up and use, simply connect the sample, waste and reagent lines and then power up the factory calibrated analyzer. Wall mount hardware is standard but an optional bench-top stand with reagent holder is also available. Accessing information for customizing an analysis routine is easily accomplished with the simple, user friendly menu structure and touch screen interface.The analyzer has two separated enclosures with two lockable doors. The top enclosure, called the electrical enclosure, includes the main power supply, the controller PCB assembly and the touchscreen interface. The bottom enclosure, called the liquids enclosure, includes all the components involved in the sample and reagent flow, mixing and reaction stages (sampling pump, reagent micro pumps and colorimetric reaction cell). Numerous analysis configurations can be programmed, depending on the accessories and the number of micro-pumps mounted in the liquid enclosure.
-
Product
Rapid Temperature Change Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is the company capable of offering a series of Rapid ESS Test Chamber,Rapid Temperature Change Test Chamber,Environmental stress screening (ESS) test chamber,Environmental stress screening test chamber,Temperature Change Test ChamberEnergy-saving design: Adopting PID + PWM principle of VRF (refrigerant flow control) technology to achieve low-temperature energy-saving operation (electronic expansion valve according to thermal energy conditions refrigerant flow servo control technology) low temperature working state, the heater does not participate in the work, through PID + The PWM regulates the flow rate and flow direction of the refrigerant, and regulates the three-way flow of the refrigerant pipe, the cold bypass pipe, and the hot bypass pipe to achieve automatic constant temperature to the working chamber. This method can reduce energy consumption by 30% under low temperature conditions.
-
Product
Magneto-inductive Testing
MAGNATEST D-HZP
-
Foerster Instruments, Incorporated
The MAGNATEST D-HZP by FOERSTER is the ultimate magneto-inductive test instrument: the fully automatic system tests materials for their properties. It operates in single coil absolute mode, making a comparator coil unnecessary. The combination of high excitation currents and complex evaluation electronic equipment detects even very small structural discrepancies. The MAGNATEST D-HZP also provides comprehensive options for documenting test results, such as test piece statistics, histogram, and test data export, which are displayed clearly on the large color display.
-
Product
Test Probe Leads, With 19-mm Tips And 4-mm Tips
U1169A
Accessory Kit
The U1169A consists of one pair (red and black) of insulated test leads, one pair of test probes with 19-mm tips and another pair of test probes with 4-mm tips. Recommended for use with Keysight handheld digital multimeters. Rated at CAT III 1000V, CAT IV 600V, 15A.
-
Product
PCIe 6.0 Protocol Analyzer
P5570A
Protocol Analyzer
Keysight PCIe 6.0 Protocol Analyzer redefines protocol debugging and validation through a new innovative CEM card form factor, bringing vast improvement in signal integrity and equalization with instant link-up to systems as well as devices under test
-
Product
Accessibility Test Probes
TF-24 Series
-
Accessibility Test Probes are designed to perform tests specified in many standards to determine compliance with safety requirements.
-
Product
Turns Ratio Meter 3 Phase Rack
TR-MARK III R 250V
-
The TR-MARK III R 250V is the successor of the famous TR-MARK III R. Besides an extended test voltage up to 250V, it offers new features and increased accuracy to make it a perfect system. A color LCD with back lighting and touch screen increases handling and user comfort. Two USB interfaces make it easy to store measurements on external storage devices and transfer easily to a personal computer or download nameplate data of xformer to test.
-
Product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
PSL-3424 Quick Test for 802.at and 802.3bt PSE's
-
Accessible from PSA Interactive or PowerShell PSA. Scans 2 to 8 PSE ports per test cycle. Automatically determines and adapts to PSE maximum assigned class. Tests PSE’s that grant full power via PD Classification or through PoE LLDP. Validates PoE Detection Acceptance and Rejection Range. Measures PSE Port Voltage at both minimum (DC MPS) and maximum (Pclass) load conditions. Reports PSE type (AT vs BT), maximum assigned class capability, and Pclass power capacity. Assesses Disconnect Power Removal response. Assesses Overload Power Removal response. Assesses LLDP Power Protocol and Allocations (PSL-3424L).
-
Product
PXI 8-slot BRIC Multiplexer, 80-Channel, 10-Pole (7 Sub-cards)
40-570A-415
Multiplexer Module
The 40-570A-415 is a 80-channel, 10-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
GENEM-C 100G Ethernet/IP Infrastructure Test Application
-
GENEM-C is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on the PROVA-C hardware appliance that is built on BittWare. GENEM-C allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model can use GENEM to validate service turn-up and modifications in the production network. GENEM is equally at home in a lab environment. It bundles wire-rate traffic generation and analysis capabilities with a network emulator and packet capture/replay function in a single software license.
-
Product
12/24 CH Insertion Loss/Return Loss Automatic Testing System
CA3201
-
UC INSTRUMENTS CA3201 12/24 CH INSERTION LOSS/RETURN LOSS AUTOMATIC TESTING SYSTEM is special designed for MPO/MTP fiber cable and multi-channel fiber optical devices like PLC device. It also can be easy changed into AWG DWDM devices testing system ifwe change 1310 /1550 nm light source into UC INSTRUMENTS’ tunable laser source.
-
Product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope
780319-01
Oscilloscope
1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
Product
Platforms
-
The use of switching systems to route instrumentation and stimulus signals to appropriate test points on a unit under test has a very crucial role to play in most electronics test systems. The sharing of test resources, connection of calibration references, load management, and many other functions are all managed by the switching system, the switching system acts as the interface between the unit under test (UUT) and the test equipment.
-
Product
Inspection Systems
-
Video Inspection Systems with?or without measurement capabilities are an excellent way to evaluate and test small items or items in?difficult to access locations. Many options are available in addition to the measurement capability. Video Inspection is used for a variety of purposes including the ability to see? and measure items that are much smaller than the eye can see or that hand tools can measure. Video systems can also reduce the eye and/or back strain associated with production environments where an operator must look in a microscope all day.
-
Product
Mobile App Testing
-
TestFort QA Lab can provide you with mobile application testing services that include testing application software on different mobile devices for its usability, consistency and functionality. Mobile application testing is an integral part of app development process and can valuably decrease your operational costs.
-
Product
6-12V Circuit Tester
TE6-0704
-
Hangzhou Tonny Electric & Tools Co., Ltd.
Do-it-yourself quality. 6-12 volt tester. Tests circuits with power on. Reliable and economical. Tests circuits, lights and fuses. Lights for easy visibility. Durably designed for a long service life . For testing 6-12 volt systems for wire breaks, shorts, fuses, lamps, relays, armatures and more. Suite able for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses.
-
Product
AstroAI Multimeter
2000
-
AstroAI Multimeter 2000 Counts Digital Multimeter with DC AC Voltmeter and Ohm Volt Amp Tester ; Measures Voltage, Current, Resistance; Tests Live Wire, Continuity
-
Product
Helmholtz Coil
-
In the measurement of magnetic fields by means of Hall probes or measuring coils it is necessary to calibrate the instruments in a known magnetic field. Our standard field coil according to Helmholtzenables to production of a magnetic field calculable with high accuracy from the dimensions and the amperage. In series arrangement with an accurate ammeter field strengths of up to 800A/cm are produced. The dield room accessible both in axial and radial direction. Helmholtz coils with fluxmeters are also useful in testing of magnets. Helmholtz coils give repeatable results as against the search coils due to which the magnets can be compared with more accuracy for their total flux and in turn their quality. Field Generating and Field Detecting Helmholtz coils are designed as per user specifications.
-
Product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
-
Product
Electrostatic Discharge Generator
SKS-0230I
-
Shanghai Sanki Electronic Industries Co., Ltd.
The electrostatic discharge generator SKS-0230I has high reliability, the host itself can withstand 30kV electrostatic discharge test; 7-inch touch LCD screen, simple interface, convenient operation; unique combination test mechanism, multiple modes, arbitrary combinations of parameters, continuous testing; Equipped with a file management system, which can save commonly used test parameters, and can also import and export test parameters through U disk; has temperature and humidity monitoring function, real-time display of temperature and humidity indicators of the experimental environment; high- pressure precision resistance and capacitance combination, long service life, and Easy to replace to meet different experimental requirements (150pF, 330pF, 330Ω, 2000Ω);
-
Product
Electrical Testing
-
Board defects are never an option. Your customer expects perfect boards, each time, every time. Electrical testing is the key in ensuring that the connectivity of a PCB is precisely as specified and that there are no defects or flaws that may cause problems down the line.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm
40-294-011
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
End of Line Test System for Automotive Seats
AS519
Test Platform
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
