Geometry
-
product
High Precision Angular Positioning, Calibration and Geometry INspection
LabStandard AIR
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.The LabStandardAIR has been designed as a “Contact Free” system and eliminates features, which may detract from achieving the optimum rotational performance. The rotating elements are supported on super high precision, air lubricated, hydrostaticbearings and are not subject to disturbances associated with gear drives.
-
product
Contactless Wafer Geometry Gauge
MX 20x series
The E+H geometry gauges are based on two heavy plates mounted parallel to each other. Embedded in the plate are a set of capacitive distance sensors. The wafer will be moved manual or automatically between the plates and measured without any movement.
-
product
Checking the Geometry and the Placement of the Weld
Based on the real geometric three-dimensional profile of the weld (groove) on the outside of a large diameter pipe, determine the offset of the center of the weld (groove) from the weld line. Provide continuous output of results through the RS-232 interface to the welding process control system. Provide a graphical picture of the current profile, the values of the specified and calculated geometric parameters to the operator.
-
product
Portable Connector End Face Geometry Interferometer
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
product
Fiber Geometry System
FG500
The FG500 is a fiber geometry system that measures the physical dimensions of the fiber including core, cladding, and coating diameter, non-circularity, and eccentricity. The FG500 is designed to produce accurate measurements quickly and with confidence.
-
product
Benchtop Sphere (d/8°) Geometry Spectrophotometers
Hunter Associates Laboratory, Inc.
Diffuse d/8° benchtop sphere spectrophotometers are recommended for transmittance color and haze measurements of transparent liquid and solid samples, and color measurements of opaque samples where it is desired to negate the effects of sample gloss and texture, as is necessary in the color formulation process when determining the effect of pigment variations irrespective of surface characteristics.
-
product
High Precision Angular Positioning Calibration and Geometry Inspection
LabStandard
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.Designed for horizontal and vertical applications with self-locking worm gearing and a high accuracy angular encoder ensures sensitivity and fine positioning for metrology and precision testing.
-
product
Entry-level Price Interferometer for Geometry Measurement of Single Fibers
3D SCOPE-V2
Specifically designed for use in a production environment, 3D Scope-V2 is a robust, compact and easy to use interferometer that brings speed and precision to operators. 3D Scope-V2 supports our Blink software platform. Non-compressed, real time and high quality images are transfered from the hardware to the software via a USB 2.0 link in addition to the automation and control commands.
-
product
High Precision Angular Position, Calibration and Geometry Inspection
GeoOrdinate
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.The GeoOrdinate has been designed specifically for the inspection of large and heavy components and is fully compatible with any shop floor environment whilst maintaining world class accuracies more commonly seen in the standards laboratory.
-
product
Integrating Sphere Solutions
An integrating sphere is a light collector which takes advantage of physical geometry to homogenize any radiation being emitted inside by relying on a high-reflectance coating material. Depending on the wavelength range the end user using a sphere with, different coatings have different advantages based on the application.
-
product
Wall Thickness Measurement Gauges
ElektroPhysik Dr. Steingroever GmbH & Co. KG
Portable wall thickness measuring device for non-destructive measurement of up to 24 mm. Thickness measurement of all non-magnetic materials such as glass, synthetic materials, stainless steel and composites; can also be used for objects with complex geometries.
-
product
Portable Spectrophotometers
Hunter Associates Laboratory, Inc.
Measure on the go—including samples on plant production floors, in storage areas, shipping departments, or virtually anywhere that’s convenient. Our portable spectrophotometer are available in Directional 45°/0° and Diffuse d/8° geometries.
-
product
Hardware and Software Complex for Measuring Geometric Parameters
Vishera
Non-contact measurement of the geometry of objects using telecentric lenses Opto Engineering, illuminators of various modifications, 3D scanner Sick Ranger. The telecentric pair, in conjunction with modern digital cameras from Basler, ensures high accuracy in measuring the geometric parameters of objects, the principle of laser triangulation ensures high accuracy and scanning speed.
-
product
AM Control System
Clamir
*Continuous monitoring of melt pool dynamics and geometry.*Ensures quality and repeatability.*Compatible with most laser heads.*Compatible with a wide range of materials.*Easy mechanical integration.*Quick configuration.*Helps to reduce CO2 emissions.
-
product
Interferometers
Sumix interferometers are designed for inspection of fiber optic ferrules, patch cords, pigtails and bare fiber in the process of polishing and assembly. They enable you to check polishing quality, test connector end face geometry per IEC, Telcordia or your own custom standards and generate reports to supply with your patch cords.
-
product
Passive Probe, 500 MHz, 2.5mm Tip
PP007-WR-1
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
product
CMM (Coordinate Measuring Machine) Solutions
A device that measures the geometry of physical objects by sensing discrete points on the surface of the object with a probe.
-
product
3D Roughness Measurement System
IF-Profiler
The If-Profiler is a handheld 3D roughness measurement system for high resolution measurement of surface finish. You measure roughness of flat and curved components with only one system. Measurements are performed both profile based (ISO 4287) and areal based (ISO 25178). The measurement system achieves flexible measurements and applications at high measurement speed. Various positions and measurement fields are traceably and intuitively measured. The IF-Profiler is also used to measure geometries with steep flanks and various coatings.
-
product
Semiconductor Equipment Manufacturers
Integrated Dynamics Engineering
With shrinking process geometries, new structural elements and a major increase in substrate size, the challenges to improving process yield and overall throughput have increased exponentially. These demands drive a stringent requirement for system stability and overall immunity from internal and external forces.
-
product
Digital Automated Fiber & Ferrule Interferometer For Single Fiber Connectors
DAFFI SF
The latest interferometer from Data-Pixel is a cost effective solution for high volumes production, without compromising on accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI SF to be robust, fast and accurate in order to meet all manufacturing or laboratory environments. With the Blink software platform, DAFFI is able to measure the end face geometry on single fiber connectors in a very short time. The Daffi interferometer accessories (flange and adapters) are fully compatible with the Daisi range, allowing the user to limit the costs of the 3D geometry measurement units.
-
product
Premium Spectral Light Meter
GL SPECTIS 1.0 TOUCH
The Spectis 1.0 Touch handheld light meter offers unmatched performance and flexibility. With an interchangeable detector, the system can be used for wide range of applications and measurement geometries. Use in the field, the lab or both!
-
product
Fiber End Face Interferometer
Thorlabs' GL16 End Face Interferometer measures and images the end face geometry of single- and multi-fiber connectors. A non-contact technique called scanning white-light interferometry (SWLI) provides high accuracy, repeatability, and reliability for fiber connector testing, particularly for pass/fail testing using IEC or Telcordia requirements. The system can be controlled locally through the touchscreen display or remotely through a browser-based application (see Software tab for details), allowing it to be easily integrated on the production floor.
-
product
Polarizing Beamsplitter (PBS)
Polarizing beamssplitters split randomly polarized beams into two orthogonal, linearly polarized components. S-polarized light is reflected at a 90 degree angle while P-polarized light is transmitted. Polarizing beamsplitters come in cube form, but custom geometries are available.
-
product
Human Radiation Spectrometers
Human radiation spectrometer is designed for express control and measurement of the activity of 137 Cs and 134 Cs gamma-emitting radionuclides in the human body, as well as for assessing the internal radiation dose (“sitting in a chair” geometry).
-
product
Benchtop Non-Contact Directional Geometry Spectrophotometers
Hunter Associates Laboratory, Inc.
Unique measurement methods that don’t require instrument contact with your samples. These benchtop spectrophotometers are perfect for samples that are not smooth, uniform or are messy. These solutions reduce sample preparation time and cleanup time while ensuring absolute measurement accuracy and consistency.
-
product
Step Probes
*Precisely controlled probe travel*Step tip geometry*Replaceable and non-replaceable versions*Plating options available
-
product
Modal tests
Modal Testing and Modal Analysis - SIMO, MIMO, and ODSEffective and affordable modal testing and analysis solution for SIMO, MIMO, and ODS testing methods. The modal test is an indispensable tool to determine natural frequencies and mode shapes of any structure. With our solution, you are able to excite the structure with an impact hammer or modal vibration shakers and easily measure the responses. Import or draw your geometry for rich visualization and animation of your structures.
-
product
Benchtop Directional (45°/0° And 0°/45°) Geometry Spectrophotometers
Hunter Associates Laboratory, Inc.
Directional (45°/0° and 0°/45°) geometry benchtop spectrophotometers replicate the human visual response to color and include applications where gloss and texture affect the color measurement.
-
product
Circular Helmholtz Coils
Helmholtz-Coils are especially designed to generate precisely defined magnetic fields from DC to the upper end of the audio frequency range and beyond. The generated fields are in a strongly linear relation to the coil current. The field- strength can be calculated exactly by analytical (or numerical) methods, based on the coils' geometry, the number of turns and the coil current.
-
product
Lithography Systems
When it comes to shaping what a chip can do, lithography systems lead the way by transferring intricate circuit designs onto substrates with unmatched precision. From prototyping to high-volume manufacturing, these tools define the geometry of modern microchips, as well performance.
