Flux Density
See Also: Density, Hysteresis Loop, Gauss
-
product
PCI High Density Pecision Resistor Card
50-298-124
The 50-298-124 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 6.97kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-146
The 40-297A-146 (PXI) and the 42-297A-146 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 5.82 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe Very High Density Multiplexer, 99-Channel, 2-Pole
40-675B-002-99/2
The 40-675B-002-99/2 (PXI) and the 42-675B-002-99/2 (PXIe) are 99-channel, 2-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 5.82MΩ
50-298-052
The 50-298-052 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI/PXIe Very High Density Multiplexer, 198-Channel, 1-Pole
40-675B-002-198/1
The 40-675B-002-198/1 (PXI) and the 42-675B-002-198/1 (PXIe) are 198-channel, 1-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
product
PXI High Density Multiplexer, 5-Bank, 16-Channel, 1-Pole
40-615A-015
The 40-615A-015 is a 5-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
SF6 Density Meter Tester
JHMD-1
Xiamen Jiahua Electrical Technology Co.,Ltd
JHMD-1 is a smart tester. By using high accuracy core units, pressure sensor, A/D, D/A transducer, 32 bit ARM MCU and TI company’s high speed signal chip, it can automatically calibrate the density relay, measure pressure at signal activity temperature, convert pressure from any temperature to 20℃ standard pressure, print test data and save for review. It identifies the fault during the test. The whole procedure is under automatically operation, JHMD-1 is a high accurate, high stable, reliable tester.
-
product
Apparent / Bulk Density Tester
Bulk Density Tester Series
The Apparent Density Tester - Bulk Density Tester series testers are used to measure apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders. There are three methods according to ASTM D 1895 that are applicable to various forms of these materials that are commonly encountered - from powders and granules to large flakes and cut fibers. The apparatus consists of a measuring cup which is polished inside and a funnel.
-
product
PXI Very High Density Versatile 2 A Multiplexer
40-612B-002
The 40-612B (PXI) and 42-612B (PXIe) Very High Density Versatile Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves.
-
product
GENASYS High Density Matrix Switch Card, 104 X 8 X 8
GX6188 Series
The GX6188 is a 6U PXI, high density matrix, GENASYS architecture switching card. The card provides the user with the ability to connect and interface resources to multiple UUT connections. The board consists of two matrices - a 104x8 and a 8x8 matrix. The GX6188 can connect to 104 UUT switching points, eight external resources and an eight channel global bus via front panel connectors. Multiple GX6188 cards can be connected using the global bus. Like other GENASYS switch cards, the GX6188 features an integral, 3-dimensional switching architecture which provides the flexibility to connect test system resources to multiple UUT connections as well as supporting an expansion bus connection without sacrificing I/O matrix connections when building multiple switch card configurations.
-
product
PXI High Density Precision Resistor Module, 9-Channel, 2Ω to 122Ω
40-298-112
The 40-298-112 is a high density programmable resistor module with 9 channels which can be set between 2Ω and 122Ω with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI 6U PXI High Density Matrix, 132x8 1-Pole
45-541-001
This 6U PXI Reed Relay Matrix Module is an ultra high-density reed relay matrix available in 132x8 format with 1- pole switching. Typical applications include signal routing in Functional ATE and data acquisition systems. The matrix is constructed using high reliability Sputtered Ruthenium Reed Relays, offering >10e9 operations to give maximum switching confidence with long life and stable contact resistance.
-
product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-140
The 40-297A-140 (PXI) and the 42-297A-140 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-021
The 40-297A-021 (PXI) and the 42-297A-021 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 925 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-015
The 40-297A-015 (PXI) and the 42-297A-015 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 920 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
High Density Isolated Serial I/O Module
AMC081/081C
The AMC081 is a flexible serial I/O module providing 16 input and 16 output channels, all of which are individually isolated. I/O transceivers meet or exceed the requirements of ANSI TIA/EIA-422-B, TIA/EIA-423-B, and ITU Recommendations V.10 and V.11. The Module has PCIe x1 route to Port 4 or Port 8.
-
product
PCI High Density Resistor Card 18-Channel, 8 Bit, 0 To 255 Ohm
50-295A-121-18/8
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Very High Density Multiplexer, 10-Channel, 8-Pole
50-670C-021-10/8
The 50-670C-021-10/8 is a 10-channel, 8-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-053
The 40-297A-053 (PXI) and the 42-297A-053 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 11.4 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI High Density MUX BRIC, 32-Chan, 10-Pole
40-570-412
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI/PXIe High Density 2A Multiplexer, 8-Bank, 16-Channel, 1-Pole
42-614D-003
The 40-614D-003 (PXI) and 42-614D-003 (PXIe) 8-bank, 16-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Solid Density Analyzers
The solid density analyzers from Anton Paar are tried and tested solutions. The Autotap and Dual Autotap tapped density analyzers conform to a wide range of international standards for the determination of bulk density. The Ultrapyc automatic gas pycnometers are ultra-simple to use and provide ultra-precise skeletal density or true density measurements of your solid materials. The Micro Rotary Riffler ensures representative sampling of the samples typically used for particle size, mercury intrusion, and gas sorption experiments from the larger amounts delivered to your lab.
-
product
LXI High Density 512x4 Matrix - 60-551-028
60-551-028
High-density single pole matrix module capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 239Ω
50-298-013
The 50-298-013 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 239Ω with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI High Density Screened Mux 49 Ch 2 Pole
40-670A-021-S-49/2
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
PXI 4-Slot High Density 2A BRIC Matrix, 29x8 2-Pole (1 Sub-card)
40-573-002-29X8
The 40-573-002-29x8 BRIC is part of a range of high density matrix modules able to switch up to 2 A at 240 VDC/250 VAC. They are available in 2, 4 or 8-slot sizes to suit most high performance matrix requirements, constructed using quality electromechanical relays for high switching confidence.
-
product
PXI High Density Precision Resistor Module, 4-Channel, 2.5Ω to 6.97kΩ
40-298-124
The 40-298-124 is a high density programmable resistor module with 4 channels which can be set between 2.5Ω and 6.97kΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 11.4MΩ
40-298-053
The 40-298-053 is a high density programmable resistor module with 6 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
LXI High Density 192x8 Matrix with BIRST
60-550-023
High-density single pole matrix module capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.





























