Wafer Resistivity
See Also: Wafer, Wafer Thickness, Wafer Failure Analysis, Wafer Edge, Wafer Mapping, Wafer Probes, Wafer Probers, Wafer Inspection, Four Point Probes
-
Product
Earth Resistance Clamp Meter
T2100
-
Clamp meters for measuring earth resistance directly on earth rods (STAKELESS METHOD) and compatible with MacrotestG series meters
-
Product
Electronic Resistance Stores
-
Is designed to reproduce the values of resistance to direct current through channels independent and galvanically isolated from each other and from the case.
-
Product
Insulation Resistance Measurement
MD 15KVR
-
The digital insulation tester model MD-15KVR is Megabras' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 15 TΩ, with 4 pre-selected test voltages, 500 V - 5 kV - 10 kV - 15 kV. Other test voltages may be selected in steps of 25 V, 100 V or 500 V.
-
Product
Sole Puncture Resistant Tester
UI-FT03-1
-
Sole Puncture Resistant Tester is to test safety shoe sole steel plate insert nail puncture resistance/penetration ability.
-
Product
Contacts Resistance Tester
JYK II
-
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
Product
Multi-Test Resistivity Measurement System
-
Sheet resistance mapping of thin films with a collinear 4-point probe, Temperature co-efficient of resistance (TCR) of thin films with collinear 4-point probe, Precision temperature co-efficient of resistance (TCR) with 2-point Kelvin probes and precision surface temperature probe, resistor testing with 2-point Kelvin probes,Precision resistor testing with a Kelvin probe card, temperature co-efficient of resistance resistor test (TCR), and Standard TCR test of multiple resistors with Kelvin probes or a probe card.
-
Product
Ground Resistivity and EarthService Tester
AD-510
-
Large, readable LCD display (2000 counts), Instant battery life indicator, Test frequency: 128 Hz (quartz generator), Test Voltage: max 30 V peak-to-peak, Range: 0,01 W ? 2 k W. Accuracy resistance measurement: 1 % 2 digits,
-
Product
Ground Resistance Inspection Box
-
AllWin Instrument Science and Technology Co., Ltd.
Check the ground resistance tester each time prior to start work everyday morning and do some relevant records.
-
Product
Battery Internal Resistance Tester
TOB-R-203
-
Xiamen Tob New Energy Technology Co., Ltd
Battery internal resistance tester used for lithium battery, lead-acid battery, Ni-Cd/Ni-MH battery and all kinds of batteries.
-
Product
Non-Trip Earth Resistance Measurement
M73
-
M73 has been developed for operators who mainly work on private installations. M73 is very easy to use, it is very small in size and it carries out all necessary tests to establish COMPLIANCE (and hence ensure SAFETY) of an electric system.
-
Product
Earth Ground Resistance Meter
1623-2
-
The Fluke 1623-2 earth ground tester measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. With the stakeless test method, the Fluke 1623-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps.
-
Product
Surface Insulation Resistance Testing
AutoSIR2™
-
One AutoSIR chassis can hold between 1 to 16 measurement cards and can monitor up to 256 x 2-point test patterns or 78 x 5-point test patterns, or 32 x 9-point test patterns at selectable intervals from minutes to days. Each channel is current limited (1 M Ω), ensuring that dendrites are preserved for failure analysis. The frequent monitoring capability provides a full picture of the electrochemical reactions taking place on a circuit assembly, and provides early trend analysis enabling tests to be curtailed, thus saving considerable test time and money.
-
Product
Earthing Resistance Tester
JYD-10A
-
transformer neutral grounding resistor is the vital need in medium voltage AC distribution network that are also called by different names like Neutral Earthling Resistors. They are taken into use to limit the current that would flow through the neutral point of a transformer or generator in the event of an earth fault. They are also used for resistance grounding of connected generators and transformers.
-
Product
Contact Resistance Measurement System
CRMS
-
The CRMS is a system designed to allow any user to measure the resistance of each set of relay contacts associated with the relay under test. The test system consists of a CONTACT RESISTANCE MEASUREMENT UNIT (CRMU), a MULTIPLE RELAY TEST RACK, as well as an interconnect CABLE ASSEMBLY. Either DC or AC energy to pick and drop relay coils under test for all contact measurements is supplied from the CRMU and easily interfaces with the Multiple Relay Test Rack. For additional and more thorough testing of relays an external relay tester can be interfaced to the Multiple Relay Test Rack to supply energy to the relay coil. It is recommended that the UTE Relay Tester With Timer/Counter (UTE Product # 15967-00) be utilized so the operator can take full advantage of the unique features it offers
-
-
Product
Insulation Resistance Measurement
MI20KVe
-
The MI-20KVe High-Voltage insulation tester is a truly portable device that allows the measurement of insulation resistances using test voltages up to 20 kV.
-
Product
Transformer Winding Resistance Tester
KRI 9310
-
KRI 9310 adopt Kelvin four-wire testing method, which effectively eliminates the influence of the resistance of the test line on the test results. It can be able to increases the current to 10A by which can test extremely low resistance to 0.01 Ω(such as amorphous alloy, Copper-nickel, nickel-chromium-iron, iron-chromium-aluminum etc). For the tested objects with high resistance value (CT/PT), the instrument can extend the range to 20 kΩ，so the wide resistance test range enables KRI9310 can cover 80% of the power transformer products on the market and switchgear bus-bar cable etc. The power of the tester use the built-in rechargeable lithium battery that can test hundreds of transformers by one time charging.
-
Product
Resistivity and IP Imaging System
ARES
-
ARES represents a well equipped resistivity and IP imaging system. Groundwater explorations, geotechnical investigations, monitoring of dams and dikes, environmental studies, pollution plumes mapping, geological surveys, mineral prospecting, archaeology, detecting of cavities, underwater, marine, borehole and cross-hole measurements.
-
Product
Insulation Resistance Measurement
MD 5KVr
-
The digital insulation tester model MD5KVR is TENTECH's cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 5 TΩ, with 4 preselected test voltages, 500 V -1 kV - 2,5 kV - 5 kV. Other test voltages, from 50 V to 5 kV, can be selected in 25 V or 500 V steps.
-
Product
Ground Earth Resistance Tester
2678X
-
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
Product
Bond Tester for Wafers 2 - 12 inch
Sigma W12
-
Bondtester for wafers or at wafer level 2” – 12” (up to 300 mm)Precise testing and Cold Bump Pull (CBP) testingLarge X/Y stages X: 600mm, Y: 370 mmForce range from 1gf – 10 kgfBump pitch down to 20 µm
-
Product
Wafer Level Multi-Die Test System
ITC55WLMD
-
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
Product
Wafer Probe Loadboards/PIB
-
DTS has a full line of standard PIBs for all major tester platforms. Custom PIB designs can accommodate any test head, prober and manipulator configuration, including probe card changers, overhead direct dock setups and cable interfaces. DTS wafer test loadboards are compatible with a variety of pogo pin interface towers. All PIBs are constructed with impedance control, precision matched line lengths, full power and ground planes and both analog and digital resources to provide high quality signal integrity directly to the device.
-
Product
Wafer Cathodoluminescence Microscope
Säntis 300
-
Attolight’s Quantitative CL-SEM offers “No Compromise” large field fast scanning simultaneous acquisition of SEM images, hyperspectral CL maps, and optical spectra. Smaller diameter wafers, or miscellaneously shaped substrates are manually loaded on intermediary 300mm susceptors subsequently handled automatically by the tool.
-
Product
Moisture Resistance/ Humidity Test
-
This test is performed for evaluating the resistance of component parts and constituent materials to the deteriorative effects of the high-humidity and heat conditions typical of tropical environments. Most tropical degradation results directly or indirectly from absorption of moisture vapor, and from surface wetting. These phenomena produce many types of deterioration, including corrosion of metals; physical distortion and decomposition of organic materials; leaching out of constituent components of materials, and detrimental changes in electrical properties.
-
Product
Earth Resistance & Resistivity Meter (for 50Hz mains)
MRU-120
-
* earth resistance measurment with 3-pole,4-pole method, * earth resistance measurement without disconnecting measured earths (using clamp), * continuity of equipotential bondings and protecting conductors * two clamps earth resistance measurement without auxiliary test probs, * earth resistivity measurement,
-
Product
Resistivity Meter of Powder Composites
RM-200
-
The resistivity meter is fully automated and does not required any adjustments. The measurement is made by using the four-point contact probe on the ring (ø60 x ø50 x 5mm) and rectangular prisms samples (6 x 6 x 60÷80mm). The measurement results are automatically saved in meter memory, what allows user to manage of data. The RM-200 contain series connection which allow the data transmission to PC.
-
Product
Silicon & Compound Wafers
-
Compound semiconductors are undergoing a major expansion addressing many new applications and using various materials such as SiC, GaN, GaAs and others, to improve the performance of new devices in several segments such as Power and Face Recognition.
-
Product
Automated Wafer Prober for Magnetic Devices and Sensors
-
Hprobe design and fabricate turnkey automated testing equipment (ATE) for electrical characterization and testing of integrated circuits under magnetic field such as MRAM (Magnetic Random Access Memory) and sensors. In each phase of the technology and product development as well as during mass manufacturing, a dedicated magnetic tester is available.
-
Product
Resistance Wire Bonding
-
Electronic Systems of Wisconsin, Inc.
ESW's Resistance Wire Bonding System comes equipped with the latest features the market has to offer. Our system is capable of bonding armatures, stators or coils. The on-screen display in our bonder makes it easy to read, track, and record your bonding data. If desired, ESW offers complete electrical testing of the part prior to the bonding sequence as well. This ensures only good parts that have been electrically tested are processed through bonding. It is our duty to make sure you never have to worry about losing important information again. Our Sales and Engineering staff will work closely with you to make sure that a bonding systems will meet your needs. See the slideshow below to see some of our Resistance Wire Bonding Testers.
